Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P064C  Glow Plug Control Module  P066B  Cylinder 1 Glow Plug Control Circuit High  P066D  Cylinder 2 Glow Plug Control Circuit High  P066F  Cylinder 3 Glow Plug Control Circuit High  P0671  Cylinder 1 Glow Plug Circuit/Open  P0672  Cylinder 2 Glow Plug Circuit/Open  P0673  Cylinder 3 Glow Plug Circuit/Open  P0674  Cylinder 4 Glow Plug Circuit/Open  P067B  Cylinder 4 Glow Plug Control Circuit High  P166F  Glow Plug Control Module Circuit Short  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P064C Glow Plug Control Module The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (2 trip detection logic). Glow plug controller Comes on DTC stored
P066B Cylinder 1 Glow Plug Control Circuit High A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug

·

Short in No. 1 glow plug circuit


Comes on DTC stored
P066D Cylinder 2 Glow Plug Control Circuit High A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug

·

Short in No. 2 glow plug circuit


Comes on DTC stored
P066F Cylinder 3 Glow Plug Control Circuit High A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug

·

Short in No. 3 glow plug circuit


Comes on DTC stored
P0671 Cylinder 1 Glow Plug Circuit/Open An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 1 glow plug

·

Open in No. 1 glow plug circuit


Comes on DTC stored
P0672 Cylinder 2 Glow Plug Circuit/Open An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 2 glow plug

·

Open in No. 2 glow plug circuit


Comes on DTC stored
P0673 Cylinder 3 Glow Plug Circuit/Open An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 3 glow plug

·

Open in No. 3 glow plug circuit


Comes on DTC stored
P0674 Cylinder 4 Glow Plug Circuit/Open An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug

·

Open in No. 4 glow plug circuit


Comes on DTC stored
P067B Cylinder 4 Glow Plug Control Circuit High A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

No. 4 glow plug

·

Short in No. 4 glow plug circuit


Comes on DTC stored
P166F Glow Plug Control Module Circuit Short A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (2 trip detection logic).
·

Glow plug controller

·

Open or short in glow plug circuit


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P064C, P066B, P066D, P066F, P067B, P0671, P0672, P0673, P0674, P116F
DTC Detection Drive Pattern Enter check mode

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0671, P0672, P0673 and/or P0674 is output A
P066B, P066D, P066F and/or P067B is output B
P064C and/or P166F is output C




A

2.CHECK GLOW PLUG CONTROLLER

B

8.CHECK HARNESS AND CONNECTOR

C

12.CHECK HARNESS AND CONNECTOR
2.CHECK GLOW PLUG CONTROLLER
a.
A241159
0.625,1.042 1.052,1.313 0.427,0.271 2.104,1.771 1.771,1.271 true 0.208,0.26 0.521,0.458 0.313,0.198 10 false *a 0.719,1.083 1.063,1.281 0.344,0.198 10 false A73 2.167,1.708 2.625,1.917 0.458,0.208 10 false BATT
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A73-1(BATT) - Body ground Always 11 to 14 V



c.

Reconnect the glow plug controller connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR
a.
A301855
0.719,2.698 1.104,2.906 0.385,0.208 0.719,3.813 1.115,4.01 0.396,0.198 1.188,4.323 1.563,4.073 true 1.865,4.063 2.177,4.302 true 1.156,3.354 1.552,3.021 true 2.177,3.313 1.844,3.021 true 0.51,2.104 0.344,1.854 true 1.51,1.917 1.333,1.688 true 2.302,1.573 2.49,1.781 true 3.167,1.771 3.219,1.406 true 0.563,2.083 0.719,2.281 0.156,0.198 10 false 1 1.531,1.927 1.688,2.125 0.156,0.198 10 false 2 2.5,1.792 2.656,1.99 0.156,0.198 10 false 3 3.125,1.781 3.281,1.979 0.156,0.198 10 false 4 0.542,2.479 0.781,2.729 0.24,0.25 10 false *a 0.75,2.729 1.146,2.948 0.396,0.219 10 false C117 0.865,3.292 1.198,3.5 0.333,0.208 10 false GL1 2.219,3.271 2.583,3.49 0.365,0.219 10 false GL2 0.75,3.833 1.146,4.042 0.396,0.208 10 false C116 0.573,3.594 0.802,3.781 0.229,0.188 10 false *b 0.885,4.24 1.208,4.438 0.323,0.198 10 false GL3 2.229,4.24 2.552,4.448 0.323,0.208 10 false GL4 0.208,0.271 0.458,0.5 0.25,0.229 10 false *1
*1 No. 1 Glow Plug Connector
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)


Disconnect connectors of the glow plug controller.


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C117-1 (GL1) - No. 1 glow plug connector terminal 1 Always Below 1 Ω
C117-2 (GL2) - No. 1 glow plug connector terminal 2 Always Below 1 Ω
C116-1 (GL3) - No. 1 glow plug connector terminal 3 Always Below 1 Ω
C116-2 (GL4) - No. 1 glow plug connector terminal 4 Always Below 1 Ω



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT GLOW PLUG

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.INSPECT GLOW PLUG
a.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

b.

Exchange the glow plugs of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plugs of normally functioning cylinders.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Using the intelligent tester, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

f.

Read the DTCs.

Result:
Result Proceed to
Same DTCs (that have been erased) A
Other DTCs B


HINT:

Check for DTCs in check mode.




A

9.REPLACE GLOW PLUG CONTROLLER

B

5.REPLACE GLOW PLUG
5.REPLACE GLOW PLUG

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Using the intelligent tester, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

g.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

8.CHECK HARNESS AND CONNECTOR
a.
A301855
0.719,2.698 1.104,2.906 0.385,0.208 0.719,3.813 1.115,4.01 0.396,0.198 1.188,4.323 1.563,4.073 true 1.865,4.063 2.177,4.302 true 1.156,3.354 1.552,3.021 true 2.177,3.313 1.844,3.021 true 0.51,2.104 0.344,1.854 true 1.51,1.917 1.333,1.688 true 2.302,1.573 2.49,1.781 true 3.167,1.771 3.219,1.406 true 0.563,2.083 0.719,2.281 0.156,0.198 10 false 1 1.531,1.927 1.688,2.125 0.156,0.198 10 false 2 2.5,1.792 2.656,1.99 0.156,0.198 10 false 3 3.125,1.781 3.281,1.979 0.156,0.198 10 false 4 0.542,2.479 0.781,2.729 0.24,0.25 10 false *a 0.75,2.729 1.146,2.948 0.396,0.219 10 false C117 0.865,3.292 1.198,3.5 0.333,0.208 10 false GL1 2.219,3.271 2.583,3.49 0.365,0.219 10 false GL2 0.75,3.833 1.146,4.042 0.396,0.208 10 false C116 0.573,3.594 0.802,3.781 0.229,0.188 10 false *b 0.885,4.24 1.208,4.438 0.323,0.198 10 false GL3 2.229,4.24 2.552,4.448 0.323,0.208 10 false GL4 0.208,0.271 0.458,0.5 0.25,0.229 10 false *1
*1 No. 1 Glow Plug Connector
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)


Disconnect connectors of the glow plug controller.


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C117-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground Always 10 kΩ or higher
C117-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground Always 10 kΩ or higher
C116-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground Always 10 kΩ or higher
C116-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.


Result:
Proceed to
OK
NG



OK

9.REPLACE GLOW PLUG CONTROLLER

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE GLOW PLUG CONTROLLER

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Using the intelligent tester, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

g.

Confirm that the DTC is not output again.

HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END

12.CHECK HARNESS AND CONNECTOR
a.
A301855
0.719,2.698 1.104,2.906 0.385,0.208 0.719,3.813 1.115,4.01 0.396,0.198 1.188,4.323 1.563,4.073 true 1.865,4.063 2.177,4.302 true 1.156,3.354 1.552,3.021 true 2.177,3.313 1.844,3.021 true 0.51,2.104 0.344,1.854 true 1.51,1.917 1.333,1.688 true 2.302,1.573 2.49,1.781 true 3.167,1.771 3.219,1.406 true 0.563,2.083 0.719,2.281 0.156,0.198 10 false 1 1.531,1.927 1.688,2.125 0.156,0.198 10 false 2 2.5,1.792 2.656,1.99 0.156,0.198 10 false 3 3.125,1.781 3.281,1.979 0.156,0.198 10 false 4 0.542,2.479 0.781,2.729 0.24,0.25 10 false *a 0.75,2.729 1.146,2.948 0.396,0.219 10 false C117 0.865,3.292 1.198,3.5 0.333,0.208 10 false GL1 2.219,3.271 2.583,3.49 0.365,0.219 10 false GL2 0.75,3.833 1.146,4.042 0.396,0.208 10 false C116 0.573,3.594 0.802,3.781 0.229,0.188 10 false *b 0.885,4.24 1.208,4.438 0.323,0.198 10 false GL3 2.229,4.24 2.552,4.448 0.323,0.208 10 false GL4 0.208,0.271 0.458,0.5 0.25,0.229 10 false *1
*1 No. 1 Glow Plug Connector
*a Front view of wire harness connector
(to Glow Plug Controller)
*b Front view of wire harness connector
(to Glow Plug Controller)


Disconnect connectors of the glow plug controller.


b.

Remove the No. 1 glow plug connector from the glow plug.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C117-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground Always 10 kΩ or higher
C117-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground Always 10 kΩ or higher
C116-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground Always 10 kΩ or higher
C116-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground Always 10 kΩ or higher


HINT:

Make sure that there are no short circuits to the battery.



d.

Reconnect the glow plug controller connector.


e.

Reinstall the No. 1 glow plug connector.


Result:
Proceed to
OK
NG



OK

13.REPLACE GLOW PLUG CONTROLLER

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
13.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>2KD-FTV STARTING>GLOW PLUG(w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Using the intelligent tester, switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>CHECK MODE PROCEDURE

Powertrain > Engine > Utility
Tester Display
Check Mode
50005 61 1

g.

Confirm that the DTC is not output again.

OK:

No DTC is output.


HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

16.REPLACE GLOW PLUG
16.REPLACE GLOW PLUG

Result:
Proceed to
NEXT



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED