Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0443 Evaporative Emission Control System Purge Control Valve Circuit The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A179391
0.958,1.573 1.167,1.167 1.167,1.167 1.271,1.167 false 1.521,1.948 1.75,2.125 0.229,0.177 10 false [A] 2.844,1.948 3.073,2.125 0.229,0.177 10 false [B] 3.896,3 4.125,3.24 0.229,0.24 10 false [C] 4.573,1.333 4.802,1.51 0.229,0.177 10 false [D] 5.094,3 5.323,3.208 0.229,0.208 10 false [E] 0.51,2.083 0.885,2.271 0.375,0.188 10 false Idling 4.229,2.521 4.969,2.865 0.74,0.344 10 false 10 minutes or more 2.594,2.521 3.333,2.885 0.74,0.365 10 false 15 minutes or more 1.313,2.552 2.083,2.833 0.771,0.281 10 false Warming up 1.375,1.083 3.406,1.406 2.031,0.323 10 false Between 40 km/h and 60 km/h (25 mph and 38 mph) 0.125,0.448 1.073,0.615 0.948,0.167 10 false Vehicle Speed

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on.

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C and all accessory switches should be off.


7.

Idle the engine for 15 minutes or more [B].

8.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0443.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



13.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 38 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


WIRING DIAGRAM

A247774
6.031,3.302 6.406,3.531 0.375,0.229 10 false ECM 5.552,0.375 5.865,0.583 0.313,0.208 10 false PRG 5.563,2.229 5.979,2.396 0.417,0.167 10 false MREL 5.188,2.333 5.5,2.563 0.313,0.229 10 false G89 5.271,2.146 5.375,2.302 0.104,0.156 10 false 8 5.188,0.49 5.51,0.698 0.323,0.208 10 false C76 5.229,0.313 5.417,0.5 0.188,0.188 10 false 23 3.219,0.969 3.948,1.271 0.729,0.302 10 false Purge VSV 3.219,0.823 3.51,1.031 0.292,0.208 10 false C69 3.146,0.396 3.26,0.542 0.115,0.146 10 false 2 3.917,0.396 4.031,0.542 0.115,0.146 10 false 1 4.552,1.979 4.76,2.135 0.208,0.156 10 false 1J 4.552,2.344 4.771,2.521 0.219,0.177 10 false 1J 2.198,2.333 2.406,2.542 0.208,0.208 10 false 1J 4.583,1.823 4.719,1.979 0.135,0.156 10 false 5 2.177,1.979 2.365,2.177 0.188,0.198 10 false 1H 2.219,1.813 2.479,2.01 0.26,0.198 10 false 1 2.927,2.115 3.198,2.323 0.271,0.208 10 false EFI 0.906,2.115 1.552,2.292 0.646,0.177 10 false BATT P/I 2.229,2.177 2.375,2.375 0.146,0.198 10 false 3 4.583,2.167 4.698,2.323 0.115,0.156 10 false 2 3.76,2.656 4.167,2.823 0.406,0.167 10 false MAIN 0.802,2.875 1.292,3.115 0.49,0.24 10 false Battery 2.771,3.146 4.271,3.375 1.5,0.229 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A080362
0.51,1.781 1.427,2.031 0.917,0.25 10 false VSV is ON 2.313,1.781 3.229,2.031 0.917,0.25 10 false VSV is OFF 1.5,1.573 1.885,1.771 0.385,0.198 10 false Air 0.333,0.875 0.542,1.052 0.208,0.177 10 false F 2.021,0.885 2.229,1.063 0.208,0.177 10 false F 0.844,1.354 1.01,1.531 0.167,0.177 10 false E 2.344,1.333 2.51,1.51 0.167,0.177 10 false E

Connect the intelligent tester to the DLC3.


b.

Disconnect the vacuum hose (charcoal canister side) from the purge VSV.


c.

Start the engine.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Evap Control
50004 61 6

f.

Place your finger on port E. Check if the disconnected port applies suction to your finger when operating the purge VSV using the intelligent tester.

OK:
Tester Operation Specified Condition
VSV ON Purge VSV port applies suction to finger
VSV OFF Purge VSV port applies no suction to finger



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

3.INSPECT PURGE VSV (POWER SOURCE)

NG

3.INSPECT PURGE VSV (POWER SOURCE)
a.
A161605
0.365,1.802 0.781,2.073 0.417,0.271 0.125,0.042 0.333,0.219 0.208,0.177 10 false *a 0.438,1.865 0.729,2.01 0.292,0.146 10 false C69
*a Front view of wire harness connector
(to Purge VSV)


Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C69-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR REPLACE FUSE (PURGE VSV - NO. 1 INTEGRATION RELAY)

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C69-1 - C76-23 (PRG) Always Below 1 Ω
C69-1 or C76-23 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

Powertrain > Engine > Clear DTCs
50002 61

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


g.

Idle the engine for 15 minutes or more.


h.

Turn the tester on.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P0443.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P0443 is output) B


HINT:

If the judgment result shows INCOMPLETE or N/A, drive the vehicle at a constant speed between 40 and 60 km/h (25 and 38 mph) for 10 minutes and check the DTC judgment result again.




A

B