Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

The air fuel ratio sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.

The air fuel ratio sensor is of the planar type and is integrated with a heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows through the heater to heat the sensor in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, thereby accelerating the sensor activation.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a Three-Way Catalytic Converter (TWC) is used. For the most efficient use of the Three-Way Catalytic Converter (TWC), the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: The value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A178930
0.21,3.128 1.089,3.298 0.878,0.17 10 Exhaust Gas 0.349,2.362 0.929,2.525 0.58,0.163 10 Element 1.623,2.937 1.008,2.441 false 2.072,2.564 2.511,2.715 0.439,0.152 10 Cover 1.774,2.913 1.965,2.633 false 1.92,3.412 2.062,3.601 0.142,0.189 10 A 1.248,3.412 1.39,3.601 0.142,0.189 10 A 2.425,3.46 3.591,3.63 1.166,0.17 10 A-A Cross Section 3.53,3.135 4.557,3.315 1.027,0.179 10 Atmospheric Air 3.531,2.452 4.733,2.622 1.203,0.17 10 Platinum Electrode 3.788,1.939 4.264,2.132 0.476,0.193 10 Heater 3.36,1.477 3.919,1.633 0.559,0.156 10 Alumina 1.861,0.589 3.067,0.968 1.207,0.378 10 Solid Electrolyte (Zirconia Element) 2.863,2.1 3.282,0.732 false 3.012,2.098 3.202,1.541 false 3.147,2.159 3.732,2.009 false 2.948,2.673 3.399,2.519 3.399,2.519 2.794,2.808 false 3.002,2.891 3.431,3.207 false 5.615,3.488 6.471,3.644 0.855,0.156 10 Air-fuel Ratio 4.607,0.745 6.14,1.09 1.533,0.345 10 ECM Monitored Air Fuel Ratio Sensor Voltage 1.008,2.441 0.915,2.441 false 1.965,2.633 2.04,2.633 false 3.431,3.207 3.511,3.207 false 3.399,2.519 3.499,2.519 false 3.06,0.732 3.28,0.732 false 3.202,1.541 3.334,1.541 false 5.286,3.11 5.488,3.267 0.203,0.157 10 12 5.502,3.11 5.705,3.267 0.203,0.157 10 13 5.713,3.11 5.916,3.267 0.203,0.157 10 14 5.937,3.11 6.14,3.267 0.203,0.157 10 15 6.146,3.11 6.349,3.267 0.203,0.157 10 16 6.356,3.11 6.559,3.267 0.203,0.157 10 17 6.579,3.11 6.782,3.267 0.203,0.157 10 18 4.921,2.841 5.16,2.997 0.24,0.156 10 2.0 4.921,2.534 5.16,2.69 0.24,0.156 10 2.5 4.921,2.225 5.16,2.381 0.24,0.156 10 3.0 4.921,1.93 5.16,2.086 0.24,0.156 10 3.5 4.921,1.626 5.16,1.782 0.24,0.156 10 4.0

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) Conditions (a) and (b) continue for 5 seconds or more
(2 trip detection logic):
(a) Air fuel ratio sensor voltage is higher than 3.8 V.
(b) Heated oxygen sensor voltage is 0.21 V or higher.
·

Open or short in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

Air fuel ratio sensor heater (Sensor 1)

·

Integration relay

·

Air fuel ratio sensor heater and integration relay circuits

·

Air induction system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on DTC stored
P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) Conditions (a) and (b) continue for 5 seconds or more
(2 trip detection logic):
(a) Air fuel ratio sensor voltage is below 2.8 V.
(b) Heated oxygen sensor voltage is below 0.59 V.
·

Open or short in air fuel ratio sensor (Sensor 1) circuit

·

Air fuel ratio sensor (Sensor 1)

·

Air fuel ratio sensor heater (Sensor 1)

·

Integration relay

·

Air fuel ratio sensor heater and integration relay circuits

·

Air induction system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


Comes on DTC stored

HINT:
·

When either of these DTCs is stored, check the air fuel ratio sensor output voltage by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the intelligent tester.

·

The ECM maintains the voltages at the A1A+ and A1A- terminals of the ECM at a constant level. Therefore, the air fuel ratio sensor output voltage cannot be confirmed without using the intelligent tester.

·

If the air fuel ratio sensor is malfunctioning, the ECM stores DTC P2195 or P2196.



MONITOR DESCRIPTION

Sensor voltage detection monitor

Under air-fuel ratio feedback control, if the air fuel ratio sensor output voltage is below 2.8 V (very rich condition) for 5 seconds despite the rear heated oxygen sensor output voltage being below 0.59 V, the ECM stores DTC P2196. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the rear heated oxygen sensor output voltage being 0.21 V or higher, DTC P2195 is stored.



MONITOR STRATEGY

Required Sensors/Components (Main) Air fuel ratio sensor
Required Sensors/Components (Related) Heated oxygen sensor
Frequency of Operation Continuous: Sensor voltage detection monitor
Duration 20 to 30 seconds: Sensor voltage detection monitor

TYPICAL ENABLING CONDITIONS

Sensor Voltage Detection Monitor
Time after engine start 30 seconds or more
Fuel system status Closed loop

TYPICAL MALFUNCTION THRESHOLDS

Sensor Voltage Detection Monitor (Lean Side Malfunction P2195)
Rear heated oxygen sensor voltage 0.21 V or higher
Air fuel ratio sensor voltage Higher than 3.8 V

Sensor Voltage Detection Monitor (Rich Side Malfunction P2196)
Rear heated oxygen sensor voltage Below 0.59 V
Air fuel ratio sensor voltage Below 2.8 V

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A301694
1.313,0.854 1.521,0.552 1.521,0.552 1.604,0.552 false 0.354,0.188 1.365,0.427 1.01,0.24 10 false Vehicle Speed 0.177,1.135 1.375,1.344 1.198,0.208 10 false 60 km/h (38 mph) 0.917,2.188 1.365,2.479 0.448,0.292 10 false Idling 0.188,2.427 1.385,2.635 1.198,0.208 10 false Ignition Switch off 2.021,2.115 2.469,2.406 0.448,0.292 10 false [A] 1.781,2.698 2.615,2.979 0.833,0.281 10 false Warming up 3,2.74 4.271,3 1.271,0.26 10 false 10 minutes or more 3.49,1.271 3.938,1.563 0.448,0.292 10 false [B] 4.385,3.146 4.833,3.438 0.448,0.292 10 false [C] 6.75,3.146 7.01,3.417 0.26,0.271 10 false [E] 5.521,2.75 6.792,3.01 1.271,0.26 10 false 10 minutes or more 6.031,0.906 6.479,1.198 0.448,0.292 10 false [D] 1.656,0.479 4.448,0.74 2.792,0.26 10 false Between 75 and 100 km/h (47 and 63 mph)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the intelligent tester on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (38 mph) for 10 minutes or more in a city area [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2195 or P2196.

13.

Check the DTC judgment result.

Intelligent tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the following procedure.



14.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


15.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P2195 or P2196.

19.

Check the DTC judgment result.

Intelligent tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-way Catalytic Converter (TWC) and located near the engine assembly.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P2195 or P2196 is output A
P2195 or P2196 and P0136, P0137 or P0138 are output
P2195 or P2196 and other DTCs are output B


HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?

Result:
Proceed to
YES
NO




YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

NO

4.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P2195 or P2196.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B




A

DTC CAUSED BY RUNNING OUT OF FUEL

B

4.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
4.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the intelligent tester on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

Powertrain > Engine > Active Test
Tester Display
Control the Injection Volume for A/F Sensor
50004 61 2

f.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the intelligent tester.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Intelligent tester Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1(Air fuel ratio) +12.5% Rich Below 3.1 V
AFS Voltage B1S1(Air fuel ratio) -12.5% Lean Higher than 3.4 V
O2S B1S2(Heated oxygen) +12.5% Rich Higher than 0.55 V
O2S B1S2(Heated oxygen) -12.5% Lean Below 0.4 V

Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.

Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction
Lean/Rich Lean/Rich Normal


HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DATA LIST / ACTIVE TEST




A

5.CHECK FOR INTAKE SYSTEM

B

13.REPLACE AIR FUEL RATIO SENSOR
5.CHECK FOR INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

OK:

No leaks in intake system.



Result:
Proceed to
OK
NG



OK

6.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

7.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

7.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL INJECTOR ASSEMBLY

NG

15.CHECK FUEL LINE
8.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injector pattern is poor).

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

9.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

9.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P2195 or P2196.


k.

Check the DTC judgment result.

Result:
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B




A

11.REPLACE ECM

B

END

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P2195 or P2196.


k.

Check the DTC judgment result.

Result:
Intelligent tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





Result:
Proceed to
NEXT



NEXT

END

13.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

j.

Input the DTC: P2195 or P2196.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B




A

END

B

15.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE