Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System)
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0412  Secondary Air Injection System Switching Valve "A" Circuit  


DESCRIPTION

The secondary air injection system injects air into the exhaust port of the cylinder head using an electric air pump, starting when the engine is started cold and operating until the catalyst warms up, in order to promote combustion of unburned fuel and decrease the amount of hydrocarbons (HC) and carbon monoxide (CO) in the exhaust gas.

A247771
1.74,1.396 2.042,1.281 2.042,1.281 1.302,1.375 false 2.469,1.99 2.385,2.354 false 3.292,2.938 3.406,3.25 false 3.448,2.688 4.375,3.542 false 4.521,1.698 4.958,1.448 false 0.802,0.708 0.688,0.313 false 0.052,0.146 0.76,0.531 0.708,0.385 10 false Diagnostic Signal 2.083,1.229 3.208,1.417 1.125,0.188 10 false Command Signal 0.458,2.156 1.698,2.479 1.24,0.323 10 false Air Injection Control Driver 1.354,0.615 1.677,0.792 0.323,0.177 10 false ECM 1.771,2.354 2.969,2.708 1.198,0.354 10 false Air Switching Valve Drive Signal 3.073,3.271 3.802,3.458 0.729,0.188 10 false Reed Valve 5.01,1.344 6.385,1.563 1.375,0.219 10 false Air Pump Drive Signal 6.26,2.063 6.583,2.24 0.323,0.177 10 false Filter 5.542,3.406 6.146,3.615 0.604,0.208 10 false Air Pump 3.875,3.552 5.083,3.771 1.208,0.219 10 false Air Switching Valve

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0412 Secondary Air Injection System Switching Valve "A" Circuit Condition 1:

After cold engine starts, all of following conditions met (1 trip detection logic):

1.

Secondary air injection system not operating (air pump OFF, air switching valve OFF)

2.

Diagnostic signal from air injection control driver 40%

3.

Battery voltage 8 V or more



Condition 2:

After cold engine starts, all of following conditions met (1 trip detection logic):

1.

Secondary air injection system operating (air pump ON, air switching valve ON)

2.

Diagnostic signal from air injection control driver 40%

3.

Battery voltage 8 V or more



Condition 1:
·

Open in air switching valve drive circuit

·

Short between air switching valve drive circuit and +B circuit

·

Air injection control driver

·

Air switching valve assembly

·

ECM


Condition 2:
·

Short between air switching valve drive circuit and body ground

·

Air injection control driver

·

Air switching valve assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the circuit containing the air switching valve of the secondary air injection system. The air injection control driver performs diagnosis of the air pump, air switching valve and itself, and sends the results of this diagnosis to the ECM as a duty signal.

When the ECM receives a signal indicating a malfunction in the air pump, air switching valve or air injection control driver, it illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Air injection control driver
Required Sensors/Components (Related) Air switching valve assembly
Frequency of Operation Once per drive cycle

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the intelligent tester on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the intelligent tester on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the intelligent tester initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the secondary air injection system pending codes: Press the ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After the "Secondary Air Injection Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0412.

16.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the ignition switch off.


WIRING DIAGRAM

A247773
3.052,3.375 4.74,3.76 1.688,0.385 10 false Air Injection Control Driver 2.708,0.646 2.813,0.802 0.104,0.156 10 false 1 2.698,1.292 2.813,1.438 0.115,0.146 10 false 6 2.698,1.927 2.813,2.073 0.115,0.146 10 false 2 2.708,2.552 2.813,2.698 0.104,0.146 10 false 1 2.635,0.823 2.906,1.031 0.271,0.208 10 false A34 2.635,2.094 2.906,2.302 0.271,0.208 10 false A34 2.958,0.708 3.344,0.896 0.385,0.188 10 false BATT 2.969,1.365 3.26,1.583 0.292,0.219 10 false VV 2.969,2.01 3.24,2.24 0.271,0.229 10 false VP 2.969,2.719 3.104,2.865 0.135,0.146 10 false E 0.583,1.833 0.688,1.979 0.104,0.146 10 false 2 0.594,2.448 0.698,2.594 0.104,0.146 10 false 1 0.906,2.156 1.75,2.479 0.844,0.323 10 false Air Switching Valve 0.906,1.979 1.208,2.125 0.302,0.146 10 false C89 1.948,3.969 2.052,4.115 0.104,0.146 10 false 2 1.948,4.479 2.052,4.625 0.104,0.146 10 false 1 2.25,4.302 2.885,4.531 0.635,0.229 10 false Air Pump 2.25,4.146 2.542,4.323 0.292,0.177 10 false A33 4.823,0.885 5.167,1.156 0.344,0.271 10 false C86 4.823,1.646 5.156,1.906 0.333,0.26 10 false C86 2.625,1.458 2.896,1.646 0.271,0.188 10 false C86 2.635,2.729 2.927,2.917 0.292,0.188 10 false C86 4.823,2.438 5.156,2.75 0.333,0.313 10 false C86 4.823,3.01 5.135,3.208 0.313,0.198 10 false C86 4.917,0.719 5.021,0.865 0.104,0.146 10 false 3 4.906,1.469 5.021,1.625 0.115,0.156 10 false 4 4.896,2.26 5.042,2.479 0.146,0.219 10 false 2 4.906,2.823 5.031,2.979 0.125,0.156 10 false 5 5.667,0.719 5.844,0.865 0.177,0.146 10 false 24 5.667,1.469 5.854,1.646 0.188,0.177 10 false 11 5.646,2.26 5.865,2.448 0.219,0.188 10 false 20 5.604,0.885 5.885,1.031 0.281,0.146 10 false C75 5.604,1.656 5.885,1.802 0.281,0.146 10 false C75 5.594,6.094 5.875,6.26 0.281,0.167 10 false C75 5.604,2.438 5.885,2.583 0.281,0.146 10 false C76 6.281,6.906 6.604,7.052 0.323,0.146 10 false ECM 5.969,0.792 6.448,1.042 0.479,0.25 10 false AIRV 5.969,1.563 6.417,1.75 0.448,0.188 10 false AIRP 5.969,2.354 6.333,2.583 0.365,0.229 10 false AIDI 4.5,0.74 4.75,0.917 0.25,0.177 10 false SIV 4.5,1.521 4.813,1.698 0.313,0.177 10 false SIP 4.573,2.344 4.844,2.594 0.271,0.25 10 false DI 4.531,3 4.771,3.177 0.24,0.177 10 false B+ 1,5.375 1.656,5.615 0.656,0.24 10 false BATT P/I 0.615,6.438 1.094,6.635 0.479,0.198 10 false Battery 3.677,5.948 4.063,6.115 0.385,0.167 10 false MAIN 2.51,5.042 2.615,5.188 0.104,0.146 10 false 1 2.469,5.208 2.698,5.375 0.229,0.167 10 false 1H 2.719,6.073 2.948,6.26 0.229,0.188 10 false 1J 4.469,5.208 4.646,5.375 0.177,0.167 10 false 1J 4.469,5.625 4.635,5.844 0.167,0.219 10 false 1J 4.51,5.042 4.615,5.188 0.104,0.146 10 false 5 2.51,6.063 2.635,6.271 0.125,0.208 10 false 3 4.51,5.448 4.615,5.625 0.104,0.177 10 false 2 3.125,6.302 4.604,6.531 1.479,0.229 10 false No. 1 Integration Relay 3.063,5.354 3.323,5.5 0.26,0.146 10 false EFI 5.594,5.615 5.885,5.802 0.292,0.188 10 false G89 5.688,5.917 5.823,6.083 0.135,0.167 10 false 3 5.698,5.458 5.802,5.604 0.104,0.146 10 false 8 5.969,6.104 6.375,6.25 0.406,0.146 10 false E1 5.958,5.625 6.365,5.771 0.406,0.146 10 false MREL 0.49,3.979 1.063,4.135 0.573,0.156 10 false A/PUMP

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR SWITCHING VALVE ASSEMBLY

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND)
a.

Disconnect the air switching valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C89-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the air switching valve connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C89-2 - C86-6 (VV) Always Below 1 Ω
C89-2 or C86-6 (VV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR