Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P1613  Secondary Air Injection Driver Malfunction  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0412).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1613 Secondary Air Injection Driver Malfunction Either of following conditions (1) or (2) met
(1) All of following conditions met (1 trip detection logic):
·

Either of air pump or air switching valve not operating

·

Diagnostic signal from air injection control driver 80%

·

Battery voltage 8 V or more


(2) Both of following conditions met (1 trip detection logic):
·

Battery voltage 8 V or more

·

Diagnostic signal from air injection control driver abnormal (duty signal other than 0, 20, 40, 80 and 100%)


All of following conditions met (1 trip detection logic):

1.

Secondary air injection system operating (air switching valve ON and air pump ON)

2.

Diagnostic signal from air injection control driver 0%

3.

Battery voltage 8 V or more



Both of following conditions met (1 trip detection logic):

1.

Battery voltage 8 V or more

2.

Diagnostic signal from air injection control driver 100%



·

Air injection control driver

·

Open in air injection control driver ground circuit


·

Short in diagnostic information signal circuit (air injection control driver - ECM)

·

Open or short in air pump and air switching valve command signal circuit (air injection control driver - ECM)

·

Open in air injection control driver ground circuit

·

Air injection control driver

·

ECM


·

Open or short in air injection control driver power source circuit

·

Open in diagnostic information signal circuit (air injection control driver - ECM)

·

Air injection control driver

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the secondary air injection system circuit or a malfunction in the air injection control driver itself. The air injection control driver performs diagnosis of the air pump, air switching valve and itself, and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump, air switching valve or air injection control driver, it immediately illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Air injection control driver
Required Sensors/Components (Related) Air switching valve assembly
Frequency of Operation Once per drive cycle

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the intelligent tester on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the intelligent tester on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the intelligent tester initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the secondary air injection system pending codes: Press the ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After the "Secondary Air Injection Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P1613.

16.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the ignition switch off.


CAUTION / NOTICE / HINT

CAUTION:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
a.
A200902
0.656,1 1,1.219 0.344,0.219 2.146,1.625 1.938,1.125 true 0.104,0.083 0.438,0.302 0.333,0.219 10 false *a 0.708,1.031 1.042,1.25 0.333,0.219 10 false C86 2.094,1.646 2.427,1.865 0.333,0.219 10 false +B
*a Front view of wire harness connector
(to Air Injection Control Driver)


Disconnect the air injection control driver connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C86-5 (+B) - Body ground Ignition Switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM, BODY GROUND)
a.

Disconnect the ECM connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-11 (AIRP) - C86-4 (SIP) Always Below 1 Ω
C75-24 (AIRV) - C86-3 (SIV) Always Below 1 Ω
C76-20 (AIDI) - C86-2 (DI) Always Below 1 Ω
C86-1 (E) - Body ground Always Below 1 Ω
C75-11 (AIRP) or C86-4 (SIP) - Body ground Always 10 kΩ or higher
C75-24 (AIRV) or C86-3 (SIV) - Body ground Always 10 kΩ or higher
C76-20 (AIDI) or C86-2 (DI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT AIR INJECTION CONTROL DRIVER (DI TERMINAL VOLTAGE)
a.
A200902
0.646,0.969 0.979,1.198 0.333,0.229 1.198,1.594 1.365,1.125 true 1.729,1.583 1.521,1.125 true 0.094,0.083 0.49,0.375 0.396,0.292 10 false *a 0.698,1.01 1.094,1.302 0.396,0.292 10 false C86 1.156,1.625 1.552,1.917 0.396,0.292 10 false E 1.677,1.615 2.073,1.906 0.396,0.292 10 false DI
*a Front view of wire harness connector
(to Air Injection Control Driver)


Disconnect the air injection control driver connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C86-2 (DI) - C86-1 (E) Ignition Switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

NG

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Disconnect the air injection control driver connector.


b.
A229922
0.646,2.479 1.01,2.698 0.365,0.219 1.146,3.031 1.365,2.604 true 1.5,3.031 1.531,2.625 true 1.865,3.021 1.667,2.625 true 2.271,3.021 1.813,2.625 true 0.646,0.323 0.958,0.479 0.313,0.156 10 false *1 2.552,0.156 2.865,0.313 0.313,0.156 10 false *2 0.99,2 1.302,2.24 0.313,0.24 10 false *a 0.813,0.781 1.135,1.01 0.323,0.229 10 false DI 0.75,1.135 1.073,1.365 0.323,0.229 10 false SIV 2.417,0.771 2.74,1 0.323,0.229 10 false AIDI 2.417,1.135 2.917,1.406 0.5,0.271 10 false AIRV 0.698,2.51 1.021,2.74 0.323,0.229 10 false C86 1.104,3.042 1.427,3.271 0.323,0.229 10 false E 1.448,3.042 1.771,3.271 0.323,0.229 10 false DI 1.792,3.042 2.115,3.271 0.323,0.229 10 false SIV 2.198,3.042 2.521,3.271 0.323,0.229 10 false SIP
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


Connect terminals DI and SIV of the wire harness connector for the air injection control driver.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 61 26
HINT:

When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



g.

Start the engine.


h.

Perform the secondary air injection system intrusive operation while the engine is idling.


i.

Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.


j.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
C86-3 (SIV) - C86-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



k.
A229922
0.719,2.479 1.042,2.719 0.323,0.24 1.26,3.042 1.385,2.625 true 1.542,3.031 1.531,2.625 true 1.885,3.042 1.667,2.625 true 2.26,3.031 1.813,2.625 true 0.677,0.292 0.99,0.448 0.313,0.156 10 false *1 2.552,0.146 2.865,0.302 0.313,0.156 10 false *2 0.969,1.969 1.281,2.125 0.313,0.156 10 false *a 2.406,0.771 2.74,1.01 0.333,0.24 10 false AIDI 0.771,1.135 1.104,1.375 0.333,0.24 10 false SIP 0.844,0.781 1.177,1.021 0.333,0.24 10 false DI 2.406,1.135 2.906,1.385 0.5,0.25 10 false AIRP 0.76,2.521 1.094,2.76 0.333,0.24 10 false C86 1.229,3.052 1.563,3.292 0.333,0.24 10 false E 1.49,3.052 1.823,3.292 0.333,0.24 10 false DI 1.781,3.052 2.115,3.292 0.333,0.24 10 false SIV 2.167,3.052 2.5,3.292 0.333,0.24 10 false SIP
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


Connect terminals DI and SIP of the wire harness connector for the air injection control driver.


l.

Connect the intelligent tester to the DLC3.


m.

Turn the ignition switch to ON.


n.

Turn the intelligent tester on.


o.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 61 26
HINT:

When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



p.

Start the engine.


q.

Perform the secondary air injection system intrusive operation while the engine is idling.


r.

Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.


s.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
C86-4 (SIP) - C86-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.REPLACE AIR INJECTION CONTROL DRIVER

NG

5.REPLACE AIR INJECTION CONTROL DRIVER

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (SYSTEM CHECK AUTOMATIC MODE)
6.CHECK WHETHER DTC OUTPUT RECURS (SYSTEM CHECK AUTOMATIC MODE)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

g.

Turn the ignition switch off and wait for at least 30 seconds.


h.

Turn the ignition switch to ON and turn the intelligent tester on.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 61 26

j.

Start the engine after the intelligent tester initialization is finished.


k.

Perform the System Check operation by pressing ENTER (Next).


l.

After operating the secondary air injection system, press the Exit button to confirm the secondary air injection system pending codes.


m.

Check Pending DTCs.

Powertrain > Engine > Trouble Codes
50001 61
OK:

No pending DTC output.



n.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Proceed to
OK
NG



OK

END

NG