Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052102 ECD SYSTEM(w/ EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P0101  Mass or Volume Air Flow Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0100 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>P0100).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0101 Mass or Volume Air Flow Circuit Range / Performance Problem After the engine is warmed up, condition (a) continues for more than 10 seconds when idling (2 trip detection logic):
(a) Mass air flow meter output is higher than 4.4 V.
Conditions (a) and (b) continue for more than 10 seconds with the engine speed at 1250 rpm or more (2 trip detection logic):
(a) VTA is higher than 0.1 V.
(b) Mass air flow meter output is below 0.7 V.
·

Air induction system

·

Mass air flow meter


Comes on DTC stored

Related Data List
DTC No. Data List
P0101
·

MAF

·

Actual EGR Valve Pos.

·

Actual Throttle position



HINT:
·

If DTC P0101 is stored due to the mass air flow meter output voltage being too low, the ECU mistakenly determines that there is less air than the actual intake air amount and EGR is decreased to match the target EGR. As a result, the following symptom may appear:

·

Combustion noise worsens


·

If DTC P0101 is stored due to the MAF meter output voltage being too high, the ECU mistakenly determines that there is more air than the actual intake air amount and EGR is increased to match the target EGR. As a result, the following symptoms may appear:

·

Misfire

·

White smoke

·

Black smoke




CONFIRMATION DRIVING PATTERN

P0101
DTC Detection Drive Pattern After warming up engine, idle engine for 20 seconds, and then maintain engine at 3000 rpm for 20 seconds

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0101)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0101 and other DTCs are output A
P0101 is output B


HINT:

If codes other than P0101 are output, perform troubleshooting for those DTCs first.




A

B

2.CHECK AIR INDUCTION SYSTEM
2.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage.

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION

OK:

No leakage from air induction system.



Result:
Proceed to
OK
NG



OK

3.REPLACE MASS AIR FLOW METER

NG

4.REPAIR OR REPLACE AIR INDUCTION SYSTEM
3.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/o Glow Plug Controller)>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.REPAIR OR REPLACE AIR INDUCTION SYSTEM
a.

Repair or replace the air induction system.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Start the engine.


e.

After warming up the engine, idle the engine for 20 seconds, and then maintain the engine at 3000 rpm for 20 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0101.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, maintain the engine at 3000 rpm for 30 seconds, and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END