Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › INTAKE SYSTEM(w/o Glow Plug Controller) › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009588 1KD-FTV INTAKE / EXHAUST _0052324 INTAKE SYSTEM(w/o Glow Plug Controller) G

1KD-FTV INTAKE / EXHAUST  INTAKE SYSTEM(w/o Glow Plug Controller)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK INTAKE AIR SYSTEM

a.

Check that there is no air suction or leaks at the points shown in the illustration.

A260059
0.396,1.49 0.521,1.49 0.521,1.49 0.75,1.927 false 0.51,2.719 0.917,2.719 false 0.479,4.354 0.885,4.354 false 2.76,0.25 2.875,0.25 2.875,0.25 3.104,0.688 false 3.896,0.302 4.021,0.302 4.021,0.302 4.25,0.74 false 5.771,2.219 5.646,2.219 5.646,2.219 5.417,2.469 false 5.771,3.073 5.646,3.073 5.646,3.073 5.417,3.323 false 4.448,6.115 4.323,6.115 4.323,6.115 4.271,5.698 false 6.719,3.375 6.594,3.375 6.594,3.375 6.375,3.615 false 5.896,4.667 5.771,4.667 5.771,4.667 5.542,4.906 false 2.052,7.167 2.177,7.167 2.177,7.167 2.396,6.729 false 5.74,3.573 5.625,3.573 5.625,3.573 5.396,3.813 false 5.875,5.396 5.75,5.396 5.75,5.396 5.531,5.646 false 3.448,3.771 3.323,3.771 3.323,3.771 3.083,3.865 false 3.729,2.01 3.604,2.01 3.604,2.01 3.375,2.26 false 1.813,5.042 1.938,5.042 1.938,5.042 2.115,4.896 false 2.458,4.438 2.583,4.438 2.583,4.438 2.677,4.365 false 0.188,1.385 0.417,1.563 0.229,0.177 10 false *1 0.281,2.615 0.521,2.813 0.24,0.198 10 false *2 0.219,4.25 0.448,4.438 0.229,0.188 10 false *3 2.552,0.156 2.885,0.385 0.333,0.229 10 false *4 3.698,0.208 4,0.396 0.302,0.188 10 false *5 5.833,2.125 6.083,2.271 0.25,0.146 10 false *6 5.854,2.99 6.083,3.135 0.229,0.146 10 false *7 4.5,6.01 4.781,6.208 0.281,0.198 10 false *12 6.792,3.281 7.021,3.427 0.229,0.146 10 false *9 5.979,4.563 6.26,4.76 0.281,0.198 10 false *10 1.771,7.042 2.115,7.281 0.344,0.24 10 false *17 5.823,3.479 6.052,3.625 0.229,0.146 10 false *8 5.969,5.302 6.25,5.5 0.281,0.198 10 false *11 3.51,3.667 3.792,3.927 0.281,0.26 10 false *15 3.813,1.917 4.094,2.146 0.281,0.229 10 false *16 1.542,4.927 1.854,5.146 0.313,0.219 10 false *13 2.208,4.333 2.521,4.521 0.313,0.188 10 false *14 0.188,0.146 0.5,0.344 0.313,0.198 10 false *A
*A w/ EGR Cooler - -
*1 Air Cleaner *2 Mass Air Flow Meter
*3 Turbocharger *4 Intercooler
*5 Intake Air Temperature Sensor *6 Diesel Throttle Body
*7 Manifold Absolute Pressure Sensor *8 EGR Control Valve
*9 Electric Vacuum Regulating Valve
(for EGR Valve)
*10 Vacuum Switching Valve
(for No. 1 Swirl Control Valve)
*11 Vacuum Switching Valve
(for No. 2 Swirl Control Valve)
*12 Swirl Control Valve
*13 Ventilation Pipe *14 EGR Cooler
*15 No. 2 EGR Valve *16 Vacuum Switching Valve
(for EGR By-pass Valve)
*17 Vacuum Pump - -


A262910
0.396,1.49 0.521,1.49 0.521,1.49 0.75,1.927 false 0.5,2.719 0.906,2.719 false 0.5,4.365 0.906,4.365 false 2.76,0.26 2.875,0.26 2.875,0.26 3.104,0.698 false 3.927,0.302 4.052,0.302 4.052,0.302 4.281,0.74 false 5.771,2.292 5.646,2.292 5.646,2.292 5.406,2.542 false 5.771,3.083 5.646,3.083 5.646,3.083 5.417,3.333 false 4.667,5.875 4.542,5.875 4.542,5.875 4.344,5.5 false 6.719,3.375 6.594,3.375 6.594,3.375 6.375,3.615 false 5.896,4.667 5.771,4.667 5.771,4.667 5.542,4.906 false 2.052,7.167 2.177,7.167 2.177,7.167 2.396,6.729 false 5.74,3.573 5.625,3.573 5.625,3.573 5.396,3.813 false 1.917,5.375 2.031,5.375 2.031,5.375 2.25,4.938 false 0.188,1.427 0.354,1.573 0.167,0.146 10 false *1 0.26,2.646 0.438,2.792 0.177,0.146 10 false *2 0.292,4.281 0.469,4.427 0.177,0.146 10 false *3 2.5,0.177 2.667,0.323 0.167,0.146 10 false *4 3.719,0.229 3.885,0.375 0.167,0.146 10 false *5 5.865,2.219 6.115,2.365 0.25,0.146 10 false *6 5.833,3 6.063,3.146 0.229,0.146 10 false *7 4.76,5.771 5.01,5.917 0.25,0.146 10 false *11 6.802,3.292 7.031,3.438 0.229,0.146 10 false *9 5.969,4.583 6.198,4.729 0.229,0.146 10 false *10 1.813,7.104 2.063,7.25 0.25,0.146 10 false *13 5.844,3.479 6.073,3.625 0.229,0.146 10 false *8 1.594,5.292 1.844,5.438 0.25,0.146 10 false *12 0.156,0.115 0.469,0.313 0.313,0.198 10 false *A
*A w/o EGR Cooler - -
*1 Air Cleaner *2 Mass Air Flow Meter
*3 Turbocharger *4 Intercooler
*5 Intake Air Temperature Sensor *6 Diesel Throttle Body
*7 Manifold Absolute Pressure Sensor *8 EGR Valve
*9 Electric Vacuum Regulating Valve
(for EGR Valve)
*10 Vacuum Switching Valve
(for Swirl Control Valve)
*11 Swirl Control Valve *12 Ventilation Pipe
*13 Vacuum Pump - -



b.

Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and cylinder head.

Condition Operation
Clogged air cleaner Clean or replace
Collapsed or deformed hoses Repair or replace
Leakage from connections Check each connection and repair
Cracks in components Check and replace


Hide 2.CHECK EXHAUST SYSTEM

a.

Check for leakage or clogging between the cylinder head and turbocharger inlet, and between the turbocharger outlet and exhaust pipe.

Condition Operation
Deformed components Repair or replace
Foreign matter in passages Remove
Leakage from components Repair or replace
Cracks in components Check or replace


Hide 3.CHECK BOOST PRESSURE

a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Warm up the engine.

HINT:

Be sure to perform the inspection when the engine coolant temperature is between 75 and 90°C (167 and 194°F).



d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.

Powertrain > Engine > Data List
Tester Display
MAF
MAP
Accel Position
Actual Throttle Position
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Fuel Press
Actual EGR Valve Pos.
EGR Close Lrn. Status
Target Booster Pressure
50003 61 319,314,404,406,368,369,370,371,54,578,427,610

e.
A176220
2.604,2.135 2.469,2.135 2.469,2.135 2.042,2.771 true 2.635,2.042 2.833,2.188 0.198,0.146 10 false *1
*1 Snapshot Record Button


Take a snapshot of the Data List items with the intelligent tester shown in the illustration.

HINT:
·

Graphs can be displayed by transferring the stored snapshot from the tester to a PC. Intelligent Viewer must be installed on the PC.

·

The condition of the turbocharger can be determined by fully depressing the accelerator pedal while driving at 15 km/h (9 mph) in 2nd gear to accelerate the vehicle (obey all laws and regulations, and pay attention to driving conditions while driving the vehicle), and then comparing MAP with Target Booster Pressure at an engine speed of 3000 rpm.




f.

Compare MAP with Target Booster Pressure.

Standard:

MAP is within 30 kPa of Target Booster Pressure when accelerating with accelerator pedal fully depressed.


HINT:
·

The specification above denotes the difference between the absolute pressure values.

·

The inspection above is only for vehicles equipped with a manual transmission.

·

If the driving inspection using the intelligent tester above cannot be performed (e.g. due to road conditions), or if the vehicle is equipped with an automatic transmission, perform the following inspection.



i.

Warm up the engine.

HINT:

Be sure to perform the inspection when the engine coolant temperature is between 75 and 90°C (167 and 194°F).



ii.
A301653
1.375,3.344 1.458,3.188 1.458,3.188 1.594,3.188 false 1.271,0.667 1.125,0.813 1.125,0.813 0.927,0.813 false 2.563,1.198 2.688,1.302 2.688,1.302 2.677,1.448 true 2.75,2.927 2.854,2.74 2.854,2.74 2.99,2.74 true 1.521,4.01 1.677,4.01 1.677,4.01 1.823,3.625 true 1.073,1.396 0.927,1.219 0.927,1.219 0.74,1.219 true 1.635,3.083 2.094,3.281 0.458,0.198 10 false SST 0.583,0.729 1.042,0.927 0.458,0.198 10 false SST 2.583,1.479 2.896,1.677 0.313,0.198 10 true *1 3,2.635 3.313,2.833 0.313,0.198 10 true *1 1.365,3.917 1.677,4.115 0.313,0.198 10 false *2 0.542,1.167 0.854,1.365 0.313,0.198 10 false *2 0.083,0.063 0.396,0.26 0.313,0.198 10 false *A 0.063,2.521 0.375,2.719 0.313,0.198 10 true *B
*A w/ EGR Cooler
*B w/o EGR Cooler
*1 Gas Filter
*2 3-Way Connector


Using a 3-way connector, connect SST (turbocharger pressure gauge) between the manifold absolute pressure sensor and the gas filter.

SST
09992-00242  


iii.

Fully apply the parking brake and chock the 4 wheels.


iv.

for Manual Transmission:

While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).

Standard pressure (Gauge pressure):

15 to 45 kPa (0.15 to 0.46 kgf/cm2, 2.1 to 6.5 psi)



v.

for Automatic Transmission:

Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).

Standard pressure (Gauge pressure):

15 to 45 kPa (0.15 to 0.46 kgf/cm2, 2.1 to 6.5 psi)


If the pressure is below the standard, the following problems may be present.

·

The intake system or exhaust system has leakage or blockage.

·

The turbocharger sub-assembly or turbo motor driver is malfunctioning.

·

The EGR valve does not close.

·

The diesel throttle body does not open.

·

The vacuum hose connected to the diesel turbo pressure sensor (manifold absolute pressure sensor) is cracked or disconnected.

·

The mass air flow meter is malfunctioning.

·

A fuel injector is malfunctioning.


If the pressure is higher than the standard, check the turbocharger and/or boost control components (turbo motor driver, pressure sensor, vacuum hose, wire harness, etc.).



g.

Chart showing the suspected trouble areas when the pressure is below the standard.

HINT:
·

○: If a problem listed in the leftmost column of the chart exists, or if the part in the leftmost column of the chart has a malfunction, the value of the Data List item in the uppermost row of the chart will meet the conditions shown in the row labeled "Value which represents a malfunction".

·

The values in the chart are applicable when the engine coolant temperature is between 75 and 90°C (167 and 194°F).

·

The values in the chart are for vehicles equipped with a manual transmission. For vehicles with an automatic transmission, use these values as a reference only as they may differ from the actual values.

·

The values in the chart are valid in an area with an absolute atmospheric pressure higher than 95 kPa. (Standard atmospheric pressure is 101 kPa. Atmospheric pressure decreases by 1 kPa for every 100 m increase in altitude, and is also affected by the current weather conditions.)

·

When the altitude increases, atmospheric pressure and MAP decrease.



Item MAP
(Absolute pressure inside intake manifold)
MAF
(Intake air flow rate)
Accel Position Actual Throttle Position Actual EGR Valve Pos. EGR Close Lrn. Status
(EGR valve fully closed position learning status)
Fuel Pressure Injection Feedback Val #1 (to #4)
Values taken from an actual normal vehicle
*1
- 90 g/sec. 99% or more 0% 0% OK - -3 to +3 mm3/st
Values which represent a malfunction
*1
MAP is below Target Booster Pressure by 30 kPa or more MAF is less than 81 g/sec. Accel Position is not fully depressed position
*2
Actual Throttle Position is not fully open position Actual EGR Valve Pos. is not valve fully closed position
*3
NG
(Determined after performing learning)
Fuel Pressure is below Target Common Rail Pressure by 10 MPa or more (Check while condition steady) Outside of above range
Turbocharger ○ ○ - - - - - -
EGR valve does not close or has problem with movement ○ ○ - - ○
(Problem with EGR valve movement)
*4
○
(EGR valve does not close)
*4
- -
Problem with diesel throttle movement ○
(Intake airflow decreases)
○ - ○ - - - -
Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists - ○ ○ - - - - -
Intake air system leakage or blockage ○ ○ - - - - - -
Exhaust gas leakage before turbocharger or blockage ○ ○ - - - - - -
Manifold absolute pressure sensor ○ ○ - - - - - -
Manifold absolute pressure sensor hose is disconnected ○ ○ - - - - - -
Mass air flow meter sub-assembly - ○ - - - - - -
Fuel system (injector, supply pump or common rail) ○ ○ - - - - ○
(Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck)
○
*5

HINT:
·

*1: These values are measured when the transmission is in 2nd gear, the accelerator pedal is fully depressed, the vehicle is accelerating, and the engine speed is 3000 rpm.

·

*2: The Accel Position is the accelerator opening angle (%) for engine control use. The value indicates around 100% when the accelerator pedal fully depressed. If the value does not indicate around 100% when the accelerator pedal fully depressed, the accelerator pedal position sensor circuit or the pedal itself is malfunctioning. When the MIL is illuminated, even with the accelerator pedal fully depressed and an Accel Position of below 70%, it means the fail-safe is restricting the accelerator.

·

*3: Check that the Actual EGR Valve Pos. is always following the Target EGR Position value (e.g. the Actual EGR Valve Pos. is around fully closed position when the Target EGR Position value indicates 0%). The EGR valve may be malfunctioning if the value is stuck or does not fluctuate smoothly. However, in some cases the EGR valve may be malfunctioning even if the Actual EGR Valve Pos. and EGR Lift Sensor Volt % values are normal. Inspect the EGR valve for any defects (deposits, valve stuck, poor movement, etc.) if necessary.

·

*4: DTC P0400 may be stored at this time. If the actual EGR valve position follows the target EGR valve position slowly, a feeling of hesitation may occur.

·

*5: If Injection Feedback Val # of a cylinder is not within -3 to +3 mm3/st, the corresponding cylinder may have a malfunction (injector or compression). However, in some cases the cylinder may be malfunctioning even if the value is within -3 to +3 mm3/st because these values are injection volume correction values calculated by the ECM at the engine idling and not correction values for the high engine load condition related to the boost pressure control and engine output performance.




Hide 4.CHECK MOTOR FOR TURBOCHARGER CONTROL OPERATION

CAUTION:
·

Wear protective gloves to prevent injuries and burns when checking the turbocharger.

·

The engine compartment becomes hot when the engine is running.




b.

Check the stroke.

NOTICE:

Make sure the connectors of the DC motor are properly installed.


i.

Turn the ignition switch from ON to off.


ii.

Check the operation of the DC motor. Check that the motor rod stroke is as shown in A to D in the illustration below.


iii.

After the DC motor operates, visually check that the vane activation link contacts the fully closed stopper.

NOTICE:

Never loosen or tighten the lock nut of the fully closed stopper.


A303040
4.5,4.156 5.354,3.125 5.354,3.125 5.573,3.125 true 5.052,0.865 5.344,0.594 5.344,0.594 5.552,0.594 false 5.302,1.646 5.823,1.646 false 5.24,2.031 5.667,2.031 false 5.635,0.51 5.948,0.667 0.313,0.156 10 false *1 5.896,1.552 6.208,1.708 0.313,0.156 10 false *2 5.74,1.948 6.052,2.104 0.313,0.156 10 false *3 0.719,4.969 1.031,5.125 0.313,0.156 10 false *4 0.896,2.125 1.208,2.281 0.313,0.156 10 false *a 5.667,3.042 5.979,3.198 0.313,0.156 10 false *b 3.813,4.51 4.125,4.667 0.313,0.156 10 false *c 1.688,0.323 1.844,0.521 0.156,0.198 10 false A 2.896,0.313 3.104,0.51 0.208,0.198 10 false B 4.219,0.281 4.375,0.479 0.156,0.198 10 false C 5.177,0.292 5.406,0.5 0.229,0.208 10 false D 1.063,2.344 2.594,2.542 1.531,0.198 10 false (mm (in.)) 0.958,2.594 2.792,2.792 1.833,0.198 10 false 10.8 (0.425) 1.146,3.281 1.833,3.479 0.688,0.198 10 false 5 (0.197) 1.604,4.104 1.74,4.281 0.135,0.177 10 false 0 1.74,4.229 1.875,4.406 0.135,0.177 10 false 0 3.031,4.24 3.188,4.438 0.156,0.198 10 false 1 4.406,4.24 4.563,4.438 0.156,0.198 10 false 2 5.76,4.229 5.917,4.427 0.156,0.198 10 false 3 1.021,4.792 1.333,4.99 0.313,0.198 10 false ON 1.031,5.125 1.375,5.323 0.344,0.198 10 false OFF 6.115,4.208 6.615,4.406 0.5,0.198 10 false (sec.)
*1 Motor Rod *2 Lock Nut
*3 Fully Closed Stopper *4 Ignition Switch
*a Motor Rod Stroke *b Fully Closed Stopper Contact
*c Ignition Switch OFF Time - -


If the result is not as specified, check the ECM (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>TERMINALS OF ECM) and turbo motor driver (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>P2563).



Hide 5.CHECK TURBO MOTOR DRIVER

a.
A156463
1.552,0.292 1.979,0.542 0.427,0.25 2.417,0.458 2.302,0.458 2.302,0.458 1.906,1.26 true 1.635,0.333 1.99,0.542 0.354,0.208 10 false C39 2.469,0.365 2.802,0.594 0.333,0.229 10 false +B 0.073,0.063 0.333,0.323 0.26,0.26 10 false *a
*a Component with harness connected
(Turbo Motor Driver)


Check the voltage of the turbo motor driver.

i.

Turn the ignition switch to ON.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Specified Condition
C39-3 (+B) - Body ground 9 to 14 V


If the result is not as specified, refer to the following procedures (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>P2563).



b.
A156464
1.583,0.271 1.99,0.5 0.406,0.229 2.135,0.875 2.417,0.479 2.417,0.479 2.583,0.479 true 2.646,0.396 3.052,0.604 0.406,0.208 10 false GND 0.083,0.073 0.417,0.323 0.333,0.25 10 false *a 1.667,0.323 1.979,0.521 0.313,0.198 10 false C39
*a Front view of wire harness connector
(to Turbo Motor Driver)


Check the resistance of the wire harness side connector.

i.

Turn the ignition switch off.


ii.

Disconnect the turbo motor driver connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Specified Condition
C39-4 (GND) - Body ground Below 1 Ω


If the result is not as specified, refer to the following procedures (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>P2563).



c.

Connect the turbo motor drive connector.


d.

Check the turbo motor signal.

A147309
1,0.948 1.344,1.188 0.344,0.24 1.458,0.948 1.781,1.177 0.323,0.229 0.667,4.365 0.667,4.219 0.667,4.219 1.031,3.146 true 2.594,4.365 2.594,4.208 2.594,4.208 2.094,3.021 true 1.615,3.156 1.615,4.365 true 0.094,0.052 0.406,0.365 0.313,0.313 10 false *a 0.5,4.396 0.865,4.542 0.365,0.146 10 false VNTI 1.417,4.396 1.823,4.542 0.406,0.146 10 false VNTO 2.531,4.406 2.719,4.563 0.188,0.156 10 false E1 3.75,0.74 4.542,0.969 0.792,0.229 10 false (a) VNTO 3.813,2.792 4.531,3 0.719,0.208 10 false (b) VNTI 6.125,0.74 7.094,1.01 0.969,0.271 10 false 5 V/Division 6.125,2.792 7.094,3.042 0.969,0.25 10 false 5 V/Division 4.458,2.115 6.146,2.354 1.688,0.24 10 false 20 msec./Division (Idling) 4.458,4.167 6.115,4.427 1.656,0.26 10 false 50 msec./Division (Idling) 1.042,0.99 1.448,1.24 0.406,0.25 10 false C22 1.5,0.99 1.875,1.219 0.375,0.229 10 false C23
*a Component with harness connected
(ECM)
- -


OK:
Tester Connection Tool Setting Condition Specified Condition
(a) Between C22-10 (VNTO) and C23-7 (E1)
(b) Between C22-17 (VNTI) and C23-7 (E1)
(a) 5 V/Division, 20 msec./Division
(b) 5 V/Division, 50 msec./Division
Idling with warm engine Refer to illustration


i.

Connect an oscilloscope to the terminals of the ECM.


ii.

While idling the engine, check the waveform of the ECM.

HINT:

The waveform varies depending on the turbocharger operation.


If the result is not as specified, replace the turbo motor driver.