The EGR system recirculates exhaust gases, and performs control so that the proper volume of exhaust gas is recirculated to suit all driving conditions. The recirculated gas mixes with the intake air, allowing the EGR system to slow down engine combustion and lower the combustion temperature. This helps reduce NOx emissions.
In order to increase circulation efficiency, the ECM adjusts the lift amount of the EGR valve and throttle valve.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0400 | Exhaust Gas Recirculation Flow | When either condition below is met:
·
Target and actual positions of the EGR valve are different (1 trip detection logic) ·
Mass air flow rate is not changed when turning on EGR valve (2 trip detection logic) |
·
EGR valve stuck ·
EGR valve does not move smoothly ·
Electric vacuum regulating valve assembly ·
Vacuum switching valve (for EGR Cut) ·
Electric vacuum regulating valve assembly circuit ·
Vacuum switching valve (for EGR Cut) circuit ·
EGR blockage in line between exhaust manifold and intake manifold ·
Mass air flow meter ·
Intake system (leaks or blockages) ·
EGR cooler ·
Exhaust system (exhaust gas leaks) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0400 | ·
MAF ·
MAP ·
Actual EGR Valve Pos. ·
Target EGR Position ·
EGR Close Lrn. Val. ·
EGR Close Lrn. Status |
| DTC Detection Drive Pattern | Decelerate from a speed of 80 km/h (50 mph) or more (release accelerator pedal for approximately 5 seconds) |
If the electric EGR control valve assembly is forcibly operated but the intake air amount does not vary, the ECM determines that the electric EGR control valve assembly is malfunctioning. The ECM then illuminates the MIL.
If the EGR valve is forcibly operated during deceleration but the intake air amount does not vary, the ECM determines that the EGR valve is malfunctioning. The ECM then illuminates the MIL (2 trip detection logic).
Inspect the fuses for circuits related to this system before performing the following inspection procedures.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0400 is output | A |
| P0400 and other DTCs are output | B |
A
B
Connect the intelligent tester to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.
| Tester Display |
|---|
| MAF |
Read the MAF value displayed on the tester while the engine is idling.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the EGR Valve Close.
| Tester Display |
|---|
| Activate the EGR Valve Close |
Read the MAF value when the EGR valve is closed using the Active Test function.
If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or to restart the engine.
Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
When "Coolant Temp" is 75°C (167°F) or higher during idling, the exhaust gas flows through the EGR cooler. If MAF does not change when the EGR is cut even though the EGR valve is operating normally, the EGR cooler may be clogged.
When idling while warming up the engine, the actuator operates and the EGR cooler is bypassed. However, if the connector of the VSV for the EGR cooler is disconnected, the EGR cooler is not bypassed and it is possible to check how clogged the EGR cooler is.
| Active Test | Result | Proceed to |
|---|---|---|
| Activate the EGR Valve Close:
Off (Open) to on (Closed) |
MAF value does not change | A |
| MAF value changes | B |
As the values shown below may differ due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly or mass air flow meter.
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
|---|---|---|
| Open (55%) | ·
Atmosphere pressure: 101 kPa ·
Intake air temperature: 30°C (86°F) ·
Engine coolant temperature: 88°C (190°F) |
3.0 to 9.0 gm/s |
| Closed (0%) | 15 to 22 gm/s |
A
B
Check the vacuum hoses.
The hoses are not damaged and are securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the electric vacuum regulating valve assembly.
Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>VACUUM REGULATING VALVE>INSPECTION
Before replacing the electric vacuum regulating valve assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the vacuum switching valve (for EGR cut).
Before replacing the vacuum switching valve (for EGR cut), perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/o Glow Plug Controller)>INSPECTION
The valve is not stuck and does not have heavy carbon deposits.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the deposit conditions in the EGR cooler and the EGR passage.
The EGR passage is not clogged and does not have heavy carbon deposits
When performing the check for deposits, check the interior of the EGR valve, EGR pipe, EGR cooler, EGR cooler bypass valve and the entire EGR passage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the vacuum hose.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR COOLER(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the vacuum switching valve (for EGR cut).
Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up.
Move the shift lever to 2nd gear and decelerate from a speed of 80 km/h (50 mph) or more (fully release the accelerator for approximately 5 seconds or more).
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
When a DTC is output, the mass air flow meter may be malfunctioning.
| Proceed to |
|---|
| NEXT |
NEXT