The VC voltage (5 V) is generated in the ECM. The voltage is used to supply power to the throttle body assembly, turbo pressure sensor, accelerator position sensor and fuel pressure sensor.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.
| Condition | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and tester on.
Check the communication between the intelligent tester and ECM.
| Condition | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the throttle position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Condition | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the throttle position sensor connector.
A
B
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY(w/o Glow Plug Controller)>REMOVAL
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Condition | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the manifold absolute pressure sensor connector.
A
B
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Condition | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the accelerator position sensor connector.
A
B
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Condition | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the fuel pressure sensor connector.
A
B
Disconnect the EGR valve position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
| Condition | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
Reconnect the EGR valve position sensor connector.
A
B
Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/o Glow Plug Controller)>REMOVAL
Disconnect the throttle position sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the EGR valve position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C22-18 (VC) - Body ground | Always | 10 kΩ or higher |
| C23-2 (VCS) - Body ground | Always | 10 kΩ or higher |
| G39-26 (VCPA) - Body ground | Always | 10 kΩ or higher |
| G39-27 (VCP2) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle position sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the EGR valve position sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG