Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052102 ECD SYSTEM(w/ EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P2563  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Range/Performance  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  P2588  Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit Low  P2589  Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit High  


DESCRIPTION

Variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the turbo motor driver. The turbo motor driver determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A158417
4.198,1.458 4.198,0.615 false 4.198,0.615 4.552,0.615 false 1.125,2.719 0.833,3.323 true 1.344,3.115 1.469,3.354 true 1.115,2.177 0.667,1.323 0.667,1.323 0.813,1.323 true 1.344,1.781 1.552,1.313 1.552,1.313 1.688,1.313 true 0.49,3.885 2.313,4.354 1.823,0.469 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly) 0.865,1.25 1.427,1.479 0.563,0.229 10 false IC No. 1 0.583,3.385 1.177,3.615 0.594,0.229 10 false IC No. 2 3.01,1.885 3.406,2.094 0.396,0.208 10 false VTA1 3,2.188 3.427,2.417 0.427,0.229 10 false VNE2 3,1.552 3.427,1.771 0.427,0.219 10 false VNVC 3,2.813 3.427,3.031 0.427,0.219 10 false VTA2 3.01,3.146 3.385,3.354 0.375,0.208 10 false E2S 3,2.5 3.406,2.708 0.406,0.208 10 false VCS 2.885,3.531 3.688,3.906 0.802,0.375 10 false Turbo Motor Driver 4.708,3.635 5.229,3.875 0.521,0.24 10 false Closed 5.708,3.635 6.302,3.865 0.594,0.229 10 false Opened 1.75,1.24 2.26,1.51 0.51,0.271 10 false Magnet 4.625,0.51 6.302,0.979 1.677,0.469 10 false Nozzle Vane Position Sensor Output Voltage (V) 0.052,2.677 0.521,3.063 0.469,0.385 10 false Sensor Vane 4.094,1.563 4.354,1.74 0.26,0.177 10 false 4.5 4.094,2.427 4.365,2.604 0.271,0.177 10 false 0.5 1.396,3.375 1.906,3.604 0.51,0.229 10 false Magnet 4.76,3.302 6.177,3.51 1.417,0.208 10 true Nozzle Vane Position

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2563 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Range/Performance Difference between VTA1 and VTA2 voltage 0.8 V or more for 0.5 seconds or more
(1 trip detection logic)
Nozzle vane position sensor (Turbocharger sub-assembly) Comes on DTC stored
P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low VTA1 voltage 0.5 V or less for 0.5 seconds or more
(1 trip detection logic)
·

Nozzle vane position sensor (Turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver


Comes on DTC stored
P2565 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High VTA1 voltage 4.5 V or more for 0.5 seconds or more
(1 trip detection logic)
·

Nozzle vane position sensor (Turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver


Comes on DTC stored
P2588 Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit Low VTA2 voltage 0.5 V or less for 0.5 seconds or more
(1 trip detection logic)
·

Nozzle vane position sensor (Turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver


Comes on DTC stored
P2589 Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit High VTA2 voltage 4.5 V or more for 0.5 seconds or more
(1 trip detection logic)
·

Nozzle vane position sensor (Turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P2563, P2564, P2565, P2588, P2589
DTC Detection Drive Pattern Ignition switch to ON for 1 second

WIRING DIAGRAM

A255060
0.39,2.96 0.745,3.117 0.355,0.156 10 C40 0.39,3.11 2.255,3.285 1.865,0.175 10 Nozzle Vane Position Sensor 5.56,3.124 6.8,3.289 1.24,0.166 10 Turbo Motor Driver 1.562,0.434 1.936,0.627 0.374,0.193 10 VTA1 5.583,0.364 5.966,0.557 0.383,0.193 10 VTA1 1.534,0.868 1.945,1.034 0.411,0.166 10 VNE2 5.583,0.775 5.994,0.94 0.411,0.166 10 VNE2 1.52,1.284 1.964,1.47 0.443,0.186 10 VNVC 5.583,1.195 6.027,1.381 0.443,0.186 10 VNVC 1.539,1.704 1.964,1.879 0.425,0.175 10 VTA2 5.583,1.615 6.008,1.79 0.425,0.175 10 VTA2 1.614,2.143 1.964,2.309 0.351,0.166 10 E2S 5.583,2.04 5.934,2.206 0.351,0.166 10 E2S 1.603,2.545 1.964,2.71 0.361,0.166 10 VCS 5.583,2.461 5.926,2.626 0.343,0.166 10 VCS 5.546,2.974 5.869,3.158 0.323,0.184 10 C39 1.987,2.026 2.116,2.183 0.128,0.156 10 5 1.987,1.597 2.116,1.753 0.128,0.156 10 4 1.987,1.171 2.116,1.327 0.128,0.156 10 3 1.987,0.755 2.116,0.912 0.128,0.156 10 2 1.987,0.36 2.116,0.516 0.128,0.156 10 1 1.987,2.466 2.116,2.623 0.128,0.156 10 6 5.389,0.352 5.541,0.541 0.152,0.189 10 9 5.389,0.763 5.513,0.952 0.124,0.189 10 8 5.389,1.174 5.541,1.363 0.152,0.189 10 1 5.347,1.58 5.564,1.769 0.216,0.189 10 10 5.347,2.019 5.564,2.208 0.216,0.189 10 11 5.389,2.449 5.541,2.638 0.152,0.189 10 6

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2563, P2564, P2565, P2588 AND/OR P2589)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P2563, P2564, P2565, P2588 and/or P2589 is output A
P2563, P2564, P2565, P2588 and/or P2589 and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - TURBO MOTOR DRIVER)

B

2.CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - TURBO MOTOR DRIVER)
a.

Disconnect the nozzle vane position sensor connector.


b.

Disconnect the turbo motor driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-1 (VTA1) - C39-9 (VTA1) Always Below 1 Ω
C40-2 (VNE2) - C39-8 (VNE2) Always Below 1 Ω
C40-3 (VNVC) - C39-1 (VNVC) Always Below 1 Ω
C40-4 (VTA2) - C39-10 (VTA2) Always Below 1 Ω
C40-5 (E2S) - C39-11 (E2S) Always Below 1 Ω
C40-6 (VCS) - C39-6 (VCS) Always Below 1 Ω
C40-1 (VTA1) or C39-9 (VTA1) - Body ground Always 10 kΩ or higher
C40-2 (VNE2) or C39-8 (VNE2) - Body ground Always 10 kΩ or higher
C40-3 (VNVC) or C39-1 (VNVC) - Body ground Always 10 kΩ or higher
C40-4 (VTA2) or C39-10 (VTA2) - Body ground Always 10 kΩ or higher
C40-5 (E2S) or C39-11 (E2S) - Body ground Always 10 kΩ or higher
C40-6 (VCS) or C39-6 (VCS) - Body ground Always 10 kΩ or higher



d.

Reconnect the turbo motor driver connector.


e.

Reconnect the nozzle vane position sensor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK TURBO MOTOR DRIVER (SENSOR POWER SOURCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK TURBO MOTOR DRIVER (SENSOR POWER SOURCE)
a.
A251333
0.417,0.865 0.854,1.125 0.438,0.26 1.417,1.052 0.792,1.677 false 1.563,1.063 1.375,1.635 false 1.875,1.063 2,1.604 false 2.021,1.063 2.625,1.625 false 0.167,0.104 0.406,0.271 0.24,0.167 10 false *a 0.5,0.917 0.792,1.115 0.292,0.198 10 false C40 0.563,1.677 0.948,1.875 0.385,0.198 10 false VNE2 1.875,1.667 2.219,1.865 0.344,0.198 10 false E2S 1.146,1.677 1.563,1.875 0.417,0.198 10 false VNVC 2.5,1.656 2.844,1.854 0.344,0.198 10 false VCS
*a Front view of with harness connector
(to Nozzle Vane Position Sensor)


Reconnect the nozzle vane position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-3 (VNVC) - C40-2 (VNE2) Ignition switch ON 4.5 to 5.5 V
C40-6 (VCS) - C40-5 (E2S) Ignition switch ON 4.5 to 5.5 V



d.

Reconnect the nozzle vane position sensor connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT TURBO MOTOR DRIVER (VTA1, VTA2 VOLTAGE)

NG

5.REPLACE TURBO MOTOR DRIVER
4.INSPECT TURBO MOTOR DRIVER (VTA1, VTA2 VOLTAGE)
A158418
0.74,0.823 1.167,1.104 0.427,0.281 1.906,2.333 2.469,2.76 false 1.781,2.344 2.073,2.771 false 1.615,2.333 1.49,2.802 false 1.479,2.333 1.104,2.802 false 0.813,0.885 1.094,1.063 0.281,0.177 10 false C39 2,2.802 2.406,2.979 0.406,0.177 10 false VTA1 1.24,2.823 1.646,3 0.406,0.177 10 false VTA2 2.458,2.802 2.865,2.979 0.406,0.177 10 false VNE2 0.854,2.813 1.177,2.99 0.323,0.177 10 false E2S 0.385,0.292 0.583,0.469 0.198,0.177 10 false *a
*a Component with harness connected
(Turbo Motor Driver)


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C39-9 (VTA1) - C39-8 (VNE2) Ignition switch ON 0.5 to 4.5 V
C39-10 (VTA2) - C39-11 (E2S) Ignition switch ON 0.5 to 4.5 V



c.

Check the difference between the voltage values.

Result:

Voltage difference between VTA1 and VTA2 is within 0.8 V



Result:
Proceed to
OK
NG



OK

5.REPLACE TURBO MOTOR DRIVER

NG

7.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)
5.REPLACE TURBO MOTOR DRIVER

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2563, P2564, P2565, P2588 AND/OR P2589)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2563, P2564, P2565, P2588 AND/OR P2589)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Clear DTCs
50002 61


e.

Start the engine.


f.

Allow the engine to idle for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Result Proceed to
P2563, P2564, P2565, P2588 and/or P2589 output again A
No DTC is output B




A

7.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

B

END

7.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.


f.

Turn the ignition switch to ON and wait for 10 seconds or more.


g.

Start the engine.


h.

Drive the vehicle with a city driving pattern at least 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END