Refer to DTC P2006 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P2006).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2009 | Intake Manifold Runner Control Circuit Low (Bank 1) | Open in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic). | ·
Vacuum switching valve (for swirl control valve) ·
Open in vacuum switching valve (for swirl control valve) circuit ·
ECM |
Comes on | DTC stored |
| P2010 | Intake Manifold Runner Control Circuit High (Bank 1) | Short in vacuum switching valve (for swirl control valve) circuit for 0.5 seconds (2 trip detection logic). | ·
Vacuum switching valve (for swirl control valve) ·
Short in vacuum switching valve (for swirl control valve) circuit ·
ECM |
Comes on | DTC stored |
| DTC Detection Drive Pattern | 2 seconds after engine is started, race engine for 1 second |
Refer to DTC P2006 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P2006).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Disconnect the vacuum hoses from the vacuum switching valve (for Swirl Control Valve).
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
| Tester Display |
|---|
| Activate the VSV for Swirl Control Valve |
Check the VSV operation when it is operated using the intelligent tester.
| Tester Operation | Specified Condition |
|---|---|
| VSV ON | Air from port E flows out through port F |
| VSV OFF | Air from port E flows out through air filter |
Reconnect the vacuum hoses.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the vacuum switching valve (for swirl control valve).
Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD(w/o Glow Plug Controller)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Vacuum Switching Valve [for Swirl Control Valve]) |
Disconnect the vacuum switching valve (for swirl control valve) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C42-2 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the vacuum switching valve (for swirl control valve) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C42-1 - C22-15 (SCV) | Always | Below 1 Ω |
| C42-1 or C22-15 (SCV) - Body ground | Always | 10 kΩ or higher |
Reconnect the vacuum switching valve (for swirl control valve) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the vacuum switching valve (for swirl control valve).
Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD(w/o Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Disconnect the No. 1 integration relay connector.
Disconnect the vacuum switching valve (for swirl control valve) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1J-5 - C42-2 | Always | Below 1 Ω |
| 1J-5 or C42-2 - Body ground | Always | 10 kΩ or higher |
Reinstall the No. 1 integration relay.
Reconnect the No. 1 integration relay connector.
Reconnect the vacuum switching valve (for swirl control valve) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the ECM power source circuit.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>ECM Power Source Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT