Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0046  Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance  


DESCRIPTION

Variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The ECM outputs a signal to the turbo motor driver, which actuates the DC motor, to control the nozzle vane position.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance Either of following conditions met:
·

DC motor duty ratio +/- 100% for 1.3 seconds or more

·

DC motor current 2.2 A or more for 5 seconds or more when motor driving

(1 trip detection logic)


·

DC motor (turbocharger sub-assembly)

·

Turbo motor driver


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P0046
DTC Detection Drive Pattern Drive the vehicle with a city driving pattern at least 10 minutes.

WIRING DIAGRAM

A242913
0.104,2.667 0.406,2.865 0.302,0.198 10 false C41 0.094,2.854 0.76,3.052 0.667,0.198 10 false DC Motor 0.094,3.021 2.01,3.208 1.917,0.188 10 false (Turbocharger Sub-assembly) 1.521,2.458 2.198,2.781 0.677,0.323 10 false Shielded 0.708,1.25 0.823,1.448 0.115,0.198 10 false 2 0.708,2 0.844,2.188 0.135,0.188 10 false 1 3.26,3.052 3.625,3.323 0.365,0.271 10 false C39 3.25,3.219 4.479,3.406 1.229,0.188 10 false Turbo Motor Driver 3.375,1.365 4.333,1.74 0.958,0.375 10 false DC Motor Control Circuit 2.969,1.26 3.333,1.5 0.365,0.24 10 false M+ 2.969,0.406 3.344,0.604 0.375,0.198 10 false +B 0.406,1.417 0.781,1.646 0.375,0.229 10 false M+ 0.417,2.156 0.792,2.385 0.375,0.229 10 false M- 2.969,2.031 3.385,2.281 0.417,0.25 10 false M- 2.958,2.646 3.417,2.875 0.458,0.229 10 false GND 2.698,1.26 2.917,1.438 0.219,0.177 10 false 12 2.781,2.042 2.917,2.208 0.135,0.167 10 false 5 2.781,0.25 2.917,0.417 0.135,0.167 10 false 3 4.802,0.5 4.938,0.667 0.135,0.167 10 false 2 2.781,2.521 2.917,2.688 0.135,0.167 10 false 4 0.708,0.24 2,0.677 1.292,0.438 10 false from MAIN Relay (Integration Relay) 5.885,0.656 6.281,0.844 0.396,0.188 10 false VNTI 4.365,0.677 4.76,0.865 0.396,0.188 10 false VNTI 5.615,0.5 5.792,0.677 0.177,0.177 10 false 17 5.969,1.865 6.313,2.125 0.344,0.26 10 false C22 5.979,2.031 6.469,2.323 0.49,0.292 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P0046)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0046 is output A
P0046 and other DTCs are output B


HINT:

If any DTCs other than P0046 are output, troubleshoot those DTCs first.




A

2.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)

B

2.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
a.

Turn the ignition switch to ON.


b.

Turn the ignition switch off and check the DC motor operation (check the operation link movement).

HINT:

When it is necessary to repeat this inspection, wait 30 seconds or more with the ignition switch off before performing the inspection.


OK:

When ignition switch is turned off, operation link moves as shown in A through D in illustration below.

Operation link and motor rod move smoothly when moving from position shown in A to that shown in B, and from position shown in B to that shown in C.


A158317
5.479,1.969 6.031,1.948 false 5.531,1.615 5.969,1.531 false 5.615,1.167 6.083,1.115 false 4.75,4.125 5.625,3.375 false 6.146,1.031 7.094,1.198 0.948,0.167 10 false Operation Link 6.052,1.448 6.688,1.646 0.635,0.198 10 false Lock Nut 6.083,1.875 6.917,2.073 0.833,0.198 10 false Stopper Bolt 5.677,3.271 7.031,3.479 1.354,0.208 10 false Stopper Bolt Contact 2.521,4.333 4.594,4.552 2.073,0.219 10 false Ignition Switch off Time (sec.) 0.427,1.896 1.573,2.25 1.146,0.354 10 false Motor Rod Stroke (mm (in.)) 1.938,0.302 2.135,0.469 0.198,0.167 10 false A 3.177,0.302 3.375,0.469 0.198,0.167 10 false B 4.531,0.302 4.729,0.469 0.198,0.167 10 false C 5.406,0.302 5.604,0.469 0.198,0.167 10 false D 0.156,4.813 1.115,5.031 0.958,0.219 10 false Ignition Switch 1.552,4.99 1.885,5.208 0.333,0.219 10 false off 1.219,4.646 1.552,4.865 0.333,0.219 10 false ON


Result:
Proceed to
OK
NG



OK

NG

3.CHECK TURBO MOTOR DRIVER
3.CHECK TURBO MOTOR DRIVER
a.

Voltage Inspection

i.
A158418
0.635,0.792 1.063,1.042 0.427,0.25 1.885,2.167 2.365,2.656 false 1.479,2.167 1.135,2.667 false 0.729,0.833 1.01,1.01 0.281,0.177 10 false C39 2.396,2.667 2.615,2.844 0.219,0.177 10 false +B 0.969,2.708 1.292,2.885 0.323,0.177 10 false GND 0.635,0.146 0.813,0.333 0.177,0.188 10 false *a
*a Component with harness connected
(Turbo Motor Driver)


Turn the ignition switch to ON.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C39-3 (+B) - C39-4 (GND) Always 11 to 14 V




b.
A303433
0.635,1.469 1.031,1.729 0.396,0.26 0.958,2.344 1.438,1.813 true 2.49,2.385 2.01,1.813 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 0.708,1.51 1.021,1.708 0.313,0.198 10 false C39 0.719,2.365 1.083,2.563 0.365,0.198 10 false GND 2.396,2.406 2.76,2.604 0.365,0.198 10 false VNTI 2.583,2.927 3.156,3.146 0.573,0.219 10 false 5 V/DIV. 1.344,4.365 2.365,4.563 1.021,0.198 10 false 50 msec./DIV. 0.5,3.365 0.865,3.563 0.365,0.198 10 false VNTI
*a Component with harness connected
(Turbo Motor Driver)


Output Waveform Inspection

i.

Turn the ignition switch to ON.


ii.

Check the waveform of the ECM connectors using an oscilloscope.

OK:
Tester Connection Switch Condition Specified Condition
C39-2 (VNTI) - C39-4 (GND) Ignition switch ON Correct waveform is as shown




Result:
Proceed to
OK
NG



OK

4.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)

NG

7.REPLACE TURBO MOTOR DRIVER
4.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE)
a.
C217215
2.021,1.219 2.479,0.792 2.479,0.792 2.552,0.792 true 1.396,1.26 0.948,0.833 0.948,0.833 0.875,0.833 true 0.125,0.156 0.302,0.333 0.177,0.177 10 false *a 2.604,0.719 3.01,1.031 0.406,0.313 10 false M- 0.615,0.74 1.063,1.021 0.448,0.281 10 false M+
*a Component without harness connected
(DC Motor)


Disconnect the DC motor connector.


b.

Measure the DC motor resistance.

Standard resistance:

1 to 100 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)

NG

8.REPLACE TURBOCHARGER SUB-ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)
a.

Disconnect the DC motor connector.


b.

Disconnect the turbo motor driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-12 (M+) - C41-2 (M+) Always Below 1 Ω
C39-5 (M-) - C41-1 (M-) Always Below 1 Ω
C39-12 (M+) or C41-2 (M+) - Body ground Always 10 kΩ or higher
C39-5 (M-) or C41-1 (M-) - Body ground Always 10 kΩ or higher



d.

Reconnect the turbo motor driver connector.


e.

Reconnect the DC motor connector.


Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0046)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0046)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.


f.

Turn the ignition switch to ON and wait for 10 seconds or more.


g.

Start the engine.


h.

Drive the vehicle with a city driving pattern at least 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Read the DTCs.

Result:
Result Proceed to
P0046 is output A
No DTC is output B




A

B

END

7.REPLACE TURBO MOTOR DRIVER

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.


f.

Turn the ignition switch to ON and wait for 10 seconds or more.


g.

Start the engine.


h.

Drive the vehicle with a city driving pattern at least 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END