Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail injection system is controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit When the following condition is met (for 5 seconds during cranking or 0.5 seconds during engine start) (1 trip detection logic):
No crankshaft position sensor signal is sent to the ECM while cranking.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate (crankshaft)

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent No crankshaft position sensor signal is input to the ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):

(a) Engine speed is 1000 rpm or more.

(b) STA signal is off.

(c) 3 seconds or more have elapsed after STA signal is switched from on to off.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate (crankshaft)

·

Camshaft timing pulley

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0335 Engine Speed
P0339

HINT:

If DTC P0335 and/or P0339 is stored, the following symptoms may appear:

·

Difficulty starting

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

P0335
DTC Detection Drive Pattern Crank or start engine

P0339
DTC Detection Drive Pattern Engine running at 1000 rpm or more with vehicle stationary

WIRING DIAGRAM

A258976
0.563,1.792 2.229,2.021 1.667,0.229 10 false Camshaft Position Sensor 0.531,4.125 2.385,4.375 1.854,0.25 10 false Crankshaft Position Sensor 1.125,2.646 1.479,2.865 0.354,0.219 10 false NE+ 1.521,2.646 1.698,2.792 0.177,0.146 10 false 1 2.76,2.229 2.938,2.375 0.177,0.146 10 false * 0.344,4.469 1.167,4.698 0.823,0.229 10 false *: Shielded 3.49,0.25 3.667,0.396 0.177,0.146 10 false * 1.125,3.344 1.458,3.531 0.333,0.188 10 false NE- 5.5,2.646 5.823,2.875 0.323,0.229 10 false NE+ 5.281,2.646 5.417,2.875 0.135,0.229 10 false 7 5.5,3.344 5.854,3.573 0.354,0.229 10 false NE- 5.906,4.177 6.323,4.448 0.417,0.271 10 false ECM 5.281,3.344 5.448,3.615 0.167,0.271 10 false 8 5.5,0.677 5.833,0.969 0.333,0.292 10 false G+ 5.208,0.677 5.417,0.865 0.208,0.188 10 false 13 5.5,1.375 5.844,1.635 0.344,0.26 10 false G- 5.208,1.375 5.438,1.552 0.229,0.177 10 false 14 1.521,3.333 1.688,3.51 0.167,0.177 10 false 2 1.521,0.667 1.719,0.896 0.198,0.229 10 false 1 1.521,1.375 1.729,1.573 0.208,0.198 10 false 2 5.906,4.042 6.313,4.25 0.406,0.208 10 false C111 0.531,3.938 0.885,4.115 0.354,0.177 10 false C6 0.552,1.615 0.833,1.792 0.281,0.177 10 false C7 1.51,3.729 1.74,3.906 0.229,0.177 10 false 3 1.271,3.615 1.448,3.802 0.177,0.188 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.

·

A DTC is also stored when the ground of a shielded wire is faulty.



PROCEDURE

1.INSPECT CRANKSHAFT POSITION SENSOR

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

7.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-1 (NE+) - C111-7 (NE+) Always Below 1 Ω
C6-2 (NE-) - C111-8 (NE-) Always Below 1 Ω
C6-1 (NE+) or C111-7 (NE+) - Body ground Always 10 kΩ or higher
C6-2 (NE-) or C111-8 (NE-) - Body ground Always 10 kΩ or higher



d.

Reconnect the crankshaft position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A208464
0.406,1.75 0.792,1.979 0.385,0.229 10 false OK 2.667,1.771 3.052,2.083 0.385,0.313 10 false NG

Check the sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE

NG

9.SECURELY REINSTALL SENSOR
4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE
a.

Check the teeth of the sensor plate.

OK:

The sensor plate teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT TIMING PULLEY

NG

10.REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
5.INSPECT CAMSHAFT TIMING PULLEY
a.

Check the teeth of the camshaft timing pulley.

OK:

The sensor plate teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

11.REPLACE CAMSHAFT TIMING PULLEY
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.SECURELY REINSTALL SENSOR

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
a.

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE CAMSHAFT TIMING PULLEY

Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and run it at 1000 rpm or more for 5 seconds or more.


e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END