Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P245C  EGR Cooler Bypass Control Circuit Low  P245D  EGR Cooler Bypass Control Circuit High  


DESCRIPTION

The vacuum switching valve (for EGR bypass valve) is controlled by the ECM, and the opening and closing of the EGR cooler bypass valve is performed according to the vacuum applied by the vacuum pump.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P245C EGR Cooler Bypass Control Circuit Low Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve (for EGR bypass valve) circuit

·

Vacuum switching valve (for EGR bypass valve)

·

ECM


Comes on DTC stored
P245D EGR Cooler Bypass Control Circuit High Open or short in the vacuum switching valve (for EGR bypass valve) for 3 seconds (1 trip detection logic).
·

Open or short in vacuum switching valve (for EGR bypass valve) circuit

·

Vacuum switching valve (for EGR bypass valve)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P245C, P245D
DTC Detection Drive Pattern Ignition switch ON for 3 seconds

WIRING DIAGRAM

A276475
2.688,1.177 3.344,1.396 0.656,0.219 10 false EFI No. 2 0.583,2.115 0.854,2.302 0.271,0.188 10 false EFI 0.604,3.208 1.313,3.469 0.708,0.26 10 false BATT P/I 3.167,0.938 3.365,1.177 0.198,0.24 10 false 2 2.771,0.938 2.938,1.125 0.167,0.188 10 false 1 2.292,0.865 2.469,1.115 0.177,0.25 10 false 5 2.302,1.521 2.458,1.708 0.156,0.188 10 false 2 2.281,2.271 2.406,2.438 0.125,0.167 10 false 3 0.25,2.594 0.417,2.823 0.167,0.229 10 false 1 2.24,2.438 2.438,2.594 0.198,0.156 10 false 1J 2.24,1.323 2.438,1.479 0.198,0.156 10 false 1J 2.24,1.042 2.479,1.281 0.24,0.24 10 false 1J 0.406,2.604 0.688,2.802 0.281,0.198 10 false 1H 0.74,3.698 1.281,3.979 0.542,0.281 10 false Battery 6.167,3.865 6.583,4.094 0.417,0.229 10 false ECM 0.74,2.813 2.573,3.167 1.833,0.354 10 false No. 1 Integration Relay 1.229,1.646 1.875,1.833 0.646,0.188 10 false MAIN 5.313,2.135 5.75,2.406 0.438,0.271 10 false G148 5.76,2.063 6.24,2.281 0.479,0.219 10 false MREL 5.458,1.958 5.635,2.125 0.177,0.167 10 false 11 3.531,1.417 5.115,1.625 1.583,0.208 10 false Vacuum Switching Valve 3.5,1.219 3.896,1.396 0.396,0.177 10 false C127 4.698,0.927 4.875,1.135 0.177,0.208 10 false 2 3.688,0.927 3.833,1.135 0.146,0.208 10 false 1 5.313,1.042 5.719,1.25 0.406,0.208 10 false C112 5.75,1.042 6.26,1.302 0.51,0.26 10 false ECBV 5.51,0.875 5.688,1.063 0.177,0.188 10 false 4 3.531,1.583 5.135,1.854 1.604,0.271 10 false (for EGR Bypass Valve)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)

Result:
Proceed to
OK
NG



OK

2.CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)

NG

5.REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)
2.CHECK VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) (POWER SOURCE CIRCUIT)
a.

Disconnect the vacuum switching valve (for EGR bypass valve) connector.


b.
A258904C02
0.594,1.125 1.052,1.406 0.458,0.281 0.25,0.25 0.563,0.448 0.313,0.198 10 false *a 0.656,1.177 1.052,1.385 0.396,0.208 10 false C127
*a Front view of wire harness connector
(to Vacuum Switching Valve (for EGR Bypass Valve))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C127-1 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the vacuum switching valve (for EGR bypass valve) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE) - ECM)
a.

Disconnect the vacuum switching valve (for EGR bypass valve) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C127-2 - C112-4 (ECBV) Always Below 1 Ω
C127-2 or C112-4 (ECBV) - Body ground Always 10 kΩ or higher



d.

Reconnect the vacuum switching valve (for EGR bypass valve) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE VACUUM SWITCHING VALVE (FOR EGR BYPASS VALVE)
a.

Replace the vacuum switching valve (for EGR bypass valve).

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR COOLER(w/ Glow Plug Controller)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the vacuum switching valve (for EGR bypass valve) connector is not 11 to 14 V, repair or replace the harness and connector between the vacuum switching valve (for EGR bypass valve) and MAIN relay (including the EFI No. 2 fuse).



Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 3 seconds.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END