Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P20CB  Exhaust Aftertreatment Fuel Injector "A" Control Circuit Stuck Open  P20CD  Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit  P20CE  Short in Exhaust Aftertreatment Fuel Injector "A" Control Circuit  


DESCRIPTION

A248426
2.302,1.479 2.833,0.26 2.833,0.26 2.979,0.26 true 2.844,1.875 3.271,1.063 3.271,1.063 3.375,1.063 true 2.958,2.292 3.281,1.729 3.281,1.729 3.344,1.729 true 2.396,2.521 2,2.885 2,2.885 1.906,2.885 true 2.25,3.313 0.792,3.771 0.792,3.771 0.792,3.875 true 1.281,1.5 0.125,0.656 0.125,0.656 0.302,0.656 true 2.844,2.875 3.229,3.292 3.229,3.292 3.354,3.292 true 0.344,0.583 2.167,0.906 1.823,0.323 10 false Turbocharger Sub-assembly 0.24,2.135 1.125,2.427 0.885,0.292 10 false Exhaust Gas 3.031,0.188 6.021,0.5 2.99,0.313 10 false Exhaust Fuel Addition Injector Assembly 3.417,1 5.51,1.51 2.094,0.51 10 false Exhaust Gas Temperature Sensor (B1S1) 3.396,1.677 5.854,2.146 2.458,0.469 10 false No. 2 Exhaust Gas Temperature Sensor (B1S2) 3.417,3.219 5.865,3.677 2.448,0.458 10 false No. 3 Exhaust Gas Temperature Sensor (B1S3) 6.281,4.042 6.677,4.302 0.396,0.26 10 false ECM 0.396,2.802 2.042,3.115 1.646,0.313 10 false DPF Catalytic Converter 0.646,3.906 2.073,4.208 1.427,0.302 10 false Air Fuel Ratio Sensor

The exhaust fuel addition injector is mounted on the outlet of the turbocharger sub-assembly, and low pressure fuel is supplied to the injector by the feed pump in the supply pump. This injector adds fuel by a control signal from the ECM.

This injector is used for two different controls: PM forced regeneration and PM reduction.

During PM forced regeneration, the injector adds fuel to raise the catalyst temperature.

In the other control, the injector helps the air-fuel ratio become rich. As a result, PM in the exhaust gas will be reduced in response to the rich air-fuel ratio.

HINT:
·

For more information on the exhaust fuel addition injector and DPF, refer to the following procedures (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If P20CB, P20CD and P20CE are present, refer to the DTC table for Diesel Particulate Filter System (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20CB Exhaust Aftertreatment Fuel Injector "A" Control Circuit Stuck Open With the exhaust fuel addition injector off, the FIVM1 output is high and the FIVM2 output is low for 3 seconds.
(1 trip detection logic)
·

Open in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on DTC stored
P20CD Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit With the exhaust fuel addition injector off, the FIVM1 output is high and the FIVM2 output is high for 0.16 seconds.
(1 trip detection logic)
·

Open in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on DTC stored
P20CE Short in Exhaust Aftertreatment Fuel Injector "A" Control Circuit With the exhaust fuel addition injector on, the FIVM1 output is low and the FIVM2 output is low 7 or more times.
(1 trip detection logic)
·

Open in exhaust fuel addition injector assembly circuit

·

Exhaust fuel addition injector assembly

·

ECM


Comes on DTC stored

HINT:

DTC P200C and/or P20CF will be present if there is an open malfunction in the exhaust fuel addition injector circuit.


CONFIRMATION DRIVING PATTERN

P20CB
DTC Detection Drive Pattern Ignition switch ON for 3 seconds

P20CD
DTC Detection Drive Pattern Ignition switch ON for 1 second

P20CE
DTC Detection Drive Pattern Drive vehicle for 20 minutes (exhaust gas temperature is 250°C (482°F) or higher).

MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVM) signals. The FIV signal is sent from the CPU to the exhaust fuel addition injector via a drive circuit inside the ECM. The FIVM signal, which is originally output current from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVM signal, the ECM judges that the current has been applied to the exhaust fuel addition injector.

This DTC will be set if the ECM judges that the number of signals of the FIV and FIVM are inconsistent.

A117827
2.76,0.344 3.188,0.604 0.427,0.26 10 false ECM 1.229,0.813 1.698,1.021 0.469,0.208 10 false CPU 1.302,1.177 1.833,1.406 0.531,0.229 10 false FIVM 1 1.302,2.063 1.813,2.302 0.51,0.24 10 false FIVM 2 1.521,2.948 1.771,3.104 0.25,0.156 10 false FIV 3.219,1.094 4.323,1.385 1.104,0.292 10 false Monitor Circuit 1 3.219,1.969 4.354,2.313 1.135,0.344 10 false Monitor Circuit 2 3.188,2.854 4.333,3.104 1.146,0.25 10 false Command Circuit 5.479,2 7.031,2.302 1.552,0.302 10 false to Fuel Addition Injector

WIRING DIAGRAM

A276475
2.688,1.177 3.313,1.344 0.625,0.167 10 false EFI No. 2 0.563,2.115 0.833,2.302 0.271,0.188 10 false EFI 0.604,3.208 1.271,3.427 0.667,0.219 10 false BATT P/I 3.167,0.938 3.292,1.104 0.125,0.167 10 false 2 2.771,0.938 2.896,1.104 0.125,0.167 10 false 1 2.292,0.865 2.417,1.031 0.125,0.167 10 false 5 2.302,1.521 2.427,1.688 0.125,0.167 10 false 2 2.281,2.271 2.406,2.438 0.125,0.167 10 false 3 0.25,2.594 0.375,2.76 0.125,0.167 10 false 1 2.24,2.438 2.5,2.667 0.26,0.229 10 false 1J 2.24,1.333 2.438,1.49 0.198,0.156 10 false 1J 2.24,1.042 2.438,1.198 0.198,0.156 10 false 1J 0.406,2.594 0.698,2.844 0.292,0.25 10 false 1H 0.74,3.698 1.271,3.948 0.531,0.25 10 false Battery 6.167,3.865 6.583,4.063 0.417,0.198 10 false ECM 0.74,2.813 2.625,3.135 1.885,0.323 10 false No. 1 Integration Relay 1.229,1.646 1.875,1.833 0.646,0.188 10 false MAIN 5.323,2.135 5.74,2.344 0.417,0.208 10 false G148 5.76,2.063 6.229,2.302 0.469,0.24 10 false MREL 5.49,1.969 5.688,2.125 0.198,0.156 10 false 11 3.667,1.406 5.021,1.948 1.354,0.542 10 false Exhaust Fuel Addition Injector Assembly 3.5,1.25 3.875,1.406 0.375,0.156 10 false C126 4.719,0.958 4.844,1.125 0.125,0.167 10 false 1 3.698,0.958 3.823,1.125 0.125,0.167 10 false 2 5.313,1.031 5.688,1.25 0.375,0.219 10 false C112 5.74,1.031 6.208,1.25 0.469,0.219 10 false FIV 5.49,0.865 5.615,1.031 0.125,0.167 10 false 5 4.406,0.927 4.667,1.083 0.26,0.156 10 false FIV 3.896,0.927 4.271,1.083 0.375,0.156 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)
a.

Inspect the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.
A204917
0.552,1.073 1.021,1.365 0.469,0.292 0.292,0.333 0.604,0.531 0.313,0.198 10 false *a 0.604,1.146 1.115,1.344 0.51,0.198 10 false C126
*a Front view of wire harness connector
(to Exhaust Fuel Addition Injector Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C126-2 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the exhaust fuel addition injector assembly connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
a.

Disconnect the exhaust fuel addition injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C126-1 (FIV) - C112-5 (FIV) Always Below 1 Ω
C126-1 (FIV) or C112-5 (FIV) - Body ground Always 10 kΩ or higher



d.

Reconnect the exhaust fuel addition injector assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Replace the exhaust fuel addition injector assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
HINT:

If the voltage at the exhaust fuel addition injector assembly connector is not 11 to 14 V, repair or replace the harness and connector between the exhaust fuel addition injector assembly and EFI MAIN relay (including the EFI No. 2 fuse).


a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Drive the vehicle for 20 minutes.

HINT:

The exhaust gas temperature increases to 250°C (482°F) or higher after driving the vehicle for 20 minutes.



d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END