Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) J

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to terminal IGSW of the ECM. The MREL output signal from the ECM causes a current to flow to the coil, closing the contacts of the MAIN relay and supplying power to terminal +B of the ECM.

WIRING DIAGRAM

A276477E07
2.75,0.885 3.708,1.073 0.958,0.188 10 false Ignition Switch 2.729,0.76 2.969,0.927 0.24,0.167 10 false G9 1.396,0.177 1.74,0.344 0.344,0.167 10 false AM2 2.823,0.5 3.167,0.667 0.344,0.167 10 false AM2 0.979,1.646 1.635,1.813 0.656,0.167 10 false BATT P/I 0.833,2.865 1.354,3.052 0.521,0.188 10 false Battery 3.333,0.49 3.604,0.656 0.271,0.167 10 false IG2 3.51,2.615 3.927,2.792 0.417,0.177 10 false MAIN 2.604,2.99 4.167,3.177 1.563,0.188 10 false No. 1 Integration Relay 2.677,1.646 3,1.833 0.323,0.188 10 false EFI 2.156,1.833 2.427,2 0.271,0.167 10 false 1H 2.167,2.281 2.385,2.458 0.219,0.177 10 false 1J 4.74,1.833 4.958,2.01 0.219,0.177 10 false 1J 4.729,2.292 4.948,2.469 0.219,0.177 10 false 1J 4.646,0.219 4.969,0.375 0.323,0.156 10 false IGN 5.552,0.365 5.969,0.542 0.417,0.177 10 false G156 5.563,1.823 5.979,2 0.417,0.177 10 false G157 5.563,2.292 5.979,2.469 0.417,0.177 10 false G156 5.563,2.75 5.99,2.906 0.427,0.156 10 false C164 5.99,0.365 6.438,0.552 0.448,0.188 10 false IGSW 5.969,1.823 6.24,2 0.271,0.177 10 false +B 5.969,2.281 6.448,2.469 0.479,0.188 10 false MREL 5.979,2.75 6.229,2.906 0.25,0.156 10 false E1 6.188,3.167 6.563,3.333 0.375,0.167 10 false ECM 2.198,1.635 2.365,1.802 0.167,0.167 10 false 1 2.615,1.948 2.781,2.115 0.167,0.167 10 false 1 4.771,2.104 4.938,2.271 0.167,0.167 10 false 2 2.865,1.948 3.031,2.115 0.167,0.167 10 false 2 2.667,0.469 2.781,0.635 0.115,0.167 10 false 5 3.625,0.479 3.792,0.646 0.167,0.167 10 false 6 2.208,2.083 2.375,2.25 0.167,0.167 10 false 3 4.771,1.646 4.938,1.813 0.167,0.167 10 false 4 5.667,0.188 5.885,0.354 0.219,0.167 10 false 24 5.677,2.552 5.844,2.719 0.167,0.167 10 false 6 5.656,2.094 5.854,2.26 0.198,0.167 10 false 11 5.979,1.469 6.427,1.646 0.448,0.177 10 false +B2 5.563,1.479 5.979,1.656 0.417,0.177 10 false G157 5.656,1.271 5.875,1.438 0.219,0.167 10 false 17 5.667,1.646 5.885,1.813 0.219,0.167 10 false 24 4.729,1.469 4.948,1.646 0.219,0.177 10 false 1J 4.771,1.281 4.938,1.448 0.167,0.167 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT ECM (+B AND +B2 VOLTAGE)
a.
A302635C17
2.781,0.188 3.292,0.458 0.51,0.271 0.188,0.24 0.729,0.5 0.542,0.26 0.188,1.083 0.344,1.854 true 2.917,1.594 3.26,0.833 true 0.188,0.958 0.688,1.635 true 0.094,0.052 0.292,0.25 0.198,0.198 10 false *a 2.844,0.229 3.26,0.438 0.417,0.208 10 false C164 0.292,1.885 1.063,2.094 0.771,0.208 10 false 24 (+B) 2.854,1.635 3.323,1.875 0.469,0.24 10 false 6 (E1) 0.24,0.281 0.677,0.49 0.438,0.208 10 true G157 0.646,1.656 1.417,1.865 0.771,0.208 10 false 17 (+B2)
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G157-24 (+B) - C164-6 (E1) Ignition switch ON 11 to 14 V
G157-17 (+B2) - C164-6 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C164-6 (E1) - Body ground Always Below 1 Ω



c.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (IGSW VOLTAGE)
a.
A302635C18
2.823,0.188 3.292,0.448 0.469,0.26 0.698,0.219 1.135,0.49 0.438,0.271 1.094,1.635 0.667,0.927 true 2.865,1.677 3.25,0.844 true 0.146,0.073 0.344,0.271 0.198,0.198 10 false *a 2.896,0.229 3.271,0.438 0.375,0.208 10 false C164 1.021,1.688 1.792,1.896 0.771,0.208 10 false 24 (IGSW) 2.719,1.708 3.208,1.927 0.49,0.219 10 false 6 (E1) 0.74,0.271 1.125,0.448 0.385,0.177 10 false G156
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G156-24 (IGSW) - C164-6 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (MREL VOLTAGE)

NG

7.INSPECT IGNITION SWITCH
4.INSPECT ECM (MREL VOLTAGE)
a.
A302635C19
2.813,0.188 3.292,0.458 0.479,0.271 0.698,0.219 1.135,0.479 0.438,0.26 1.094,1.635 0.729,0.792 true 2.865,1.677 3.25,0.844 true 0.146,0.073 0.344,0.271 0.198,0.198 10 false *a 2.885,0.229 3.26,0.427 0.375,0.198 10 false C164 1.021,1.688 1.792,1.896 0.771,0.208 10 false 11 (MREL) 2.719,1.708 3.208,1.927 0.49,0.219 10 false 6 (E1) 0.74,0.271 1.125,0.5 0.385,0.229 10 false G156
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G156-11 (MREL) - C164-6 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 INTEGRATION RELAY (MAIN RELAY)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (MAIN RELAY)
a.

Inspect the No. 1 integration relay (MAIN relay).

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (MAIN RELAY - ECM, MAIN RELAY - BODY GROUND)

NG

REPLACE INTEGRATION NO.1 RELAY (MAIN RELAY)

6.CHECK HARNESS AND CONNECTOR (MAIN RELAY - ECM, MAIN RELAY - BODY GROUND)
a.

Check the harness and connector between the No. 1 integration relay (MAIN relay) and ECM.

i.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-4 - G157-24 (+B) Always Below 1 Ω
1J-5 - G157-17 (+B2) Always Below 1 Ω
1J-2 - G156-11 (MREL) Always Below 1 Ω
1J-4 or G157-24 (+B) - Body ground Always 10 kΩ or higher
1J-5 or G157-17 (+B2) - Body ground Always 10 kΩ or higher
1J-2 or G156-11 (MREL) - Body ground Always 10 kΩ or higher



iv.

Reconnect the ECM connector.


v.

Reinstall the No. 1 integration relay.



b.

Check the harness and connector between the No. 1 integration relay (MAIN relay) and body ground.

i.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-3 - Body ground Always Below 1 Ω



iii.

Reinstall the No. 1 integration relay.



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH, IGNITION SWITCH - ECM)

NG