Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter and detects the intake air temperature.

A thermistor built into the sensor changes its resistance value according to the intake air temperature.

The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The intake air temperature sensor is connected to the ECM.

The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.

A208462E12
1.469,1.979 1.625,1.74 1.625,1.74 1.771,1.74 false 0.208,0.146 0.688,0.323 0.479,0.177 10 false (Fig. 1) 0.208,0.542 1.198,0.719 0.99,0.177 10 false Resistance kΩ 1.813,1.656 2.802,1.896 0.99,0.24 10 false Acceptable 1.208,4.063 2.51,4.219 1.302,0.156 10 false Temperature °C (°F)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0112 Intake Air Temperature Circuit Low Input Short in the intake air temperature sensor for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


- DTC stored
P0113 Intake Air Temperature Circuit High Input Open in the intake air temperature sensor for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter)

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0112 Intake Air
P0113

HINT:
·

If DTC P0112 and/or P0113 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P0112 or P0113 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine / Data List / Intake Air.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



CONFIRMATION DRIVING PATTERN

P0112, P0113
DTC Detection Drive Pattern Ignition switch ON for 0.5 seconds

WIRING DIAGRAM

A210074E56
0.438,2.083 2.563,2.51 2.125,0.427 10 false Intake Air Temperature Sensor (Built into Mass Air Flow Meter) 2.063,0.667 2.479,0.844 0.417,0.177 10 false THA 2.167,1.26 2.594,1.49 0.427,0.229 10 false E2 5.875,2.427 6.396,2.625 0.521,0.198 10 false ECM 6.26,0.219 6.49,0.396 0.229,0.177 10 false 5 V 5.542,0.667 5.969,0.844 0.427,0.177 10 false THA 5.563,1.281 6.198,1.5 0.635,0.219 10 false ETHA 6.177,0.531 6.458,0.719 0.281,0.188 10 false R 2.458,0.854 2.729,1.073 0.271,0.219 10 false 1 2.458,1.479 2.781,1.667 0.323,0.188 10 false 2 5.344,0.667 5.542,0.823 0.198,0.156 10 false 7 5.344,1.271 5.521,1.5 0.177,0.229 10 false 1 0.438,1.906 0.885,2.073 0.448,0.167 10 false C115 5.854,2.281 6.271,2.427 0.417,0.146 10 false C167

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

d.

Read the value.

OK:

Same as actual intake air temperature


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as actual intake air temperature) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A128460C04
0.344,3.354 0.771,3.563 0.427,0.208 1,3.969 1.323,3.479 true 1.875,3.979 1.573,3.49 true 0.688,0.292 1,0.49 0.313,0.198 10 false *1 2.667,0.25 2.979,0.448 0.313,0.198 10 false *2 0.156,2.406 0.469,2.604 0.313,0.198 10 false *a 2.448,1.052 2.906,1.25 0.458,0.198 10 false THA 2.458,1.49 2.938,1.667 0.479,0.177 10 false ETHA 0.385,3.375 0.75,3.573 0.365,0.198 10 false C115 0.896,3.99 1.198,4.167 0.302,0.177 10 false THA 1.833,4 2.146,4.198 0.313,0.198 10 false E2
*1 Mass air flow meter
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Connect terminals 1 (THA) and 2 (E2) of the mass air flow meter wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

f.

Read the value.

OK:

140°C (284°F) or higher



g.

Reconnect the mass air flow meter connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER.

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER.

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C115-1 (THA) - C167-7 (THA) Always Below 1 Ω
C115-2 (E2) - C167-1 (ETHA) Always Below 1 Ω



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633C06
0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.604,0.25 2.917,0.448 0.313,0.198 10 false *2 2.531,1.094 2.844,1.292 0.313,0.198 10 false THA 2.521,1.51 2.885,1.708 0.365,0.198 10 false ETHA
*1 Mass Air Flow Meter
*2 ECM


Disconnect the mass air flow meter connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air.

Powertrain > Engine > Data List
Tester Display
Intake Air
50003 61 318

e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the mass air flow meter connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE MASS AIR FLOW METER

NG

10.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
8.REPLACE MASS AIR FLOW METER

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 1 second.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C115-1 (THA) or C167-7 (THA) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED