Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  


DESCRIPTION

The throttle position sensor is mounted on the diesel throttle body assembly and detects the opening angle of the throttle valve. This sensor is an electronic sensor and uses Hall-effect elements.

When the throttle valve is fully closed, a voltage of approximately 0.7 V is applied to terminal VLU of the ECM. The voltage applied to terminal VLU of the ECM increases in proportion to the opening angle of the throttle valve and becomes approximately 3.5 to 4.0 V when the throttle valve is fully opened.

The ECM determines the vehicle driving conditions from the signals input to its VLU terminal. The data is one of the pieces of information used for EGR control, etc.

A128639E17
2.51,2.073 2.844,3.073 false 2.385,2.615 2.188,3.104 false 2.208,0.781 2.406,1.271 false 1.698,0.219 3.25,0.427 1.552,0.208 10 false Throttle Position Sensor 2.844,3.094 3.385,3.292 0.542,0.198 10 false Hall IC 4.344,0.615 4.75,0.823 0.406,0.208 10 false ECM 4.385,1.115 4.677,1.313 0.292,0.198 10 false 5 V 3.5,1.167 3.938,1.365 0.438,0.198 10 false VCVL 3.573,1.781 4.031,1.979 0.458,0.198 10 false VLU 3.5,2.385 4.031,2.563 0.531,0.177 10 false EVLU 3.146,1.167 3.406,1.365 0.26,0.198 10 false VC 3.146,2.385 3.385,2.583 0.24,0.198 10 false E2 3.146,1.781 3.51,1.979 0.365,0.198 10 false VTA 1.813,3.125 2.406,3.333 0.594,0.208 10 false Magnet 1.802,0.615 2.396,0.823 0.594,0.208 10 false Magnet

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input Throttle position sensor output (VLU) is below 0.2 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open or short in VLU circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input Throttle position sensor output (VLU) is higher than 4.8 V for 3 seconds (1 trip detection logic).
·

Throttle position sensor

·

Open in E2 circuit

·

VC and VLU circuits are short-circuited

·

ECM


Comes on DTC stored

HINT:

If DTC P0122 and/or P0123 is stored, the following symptoms may appear:


- Intake booming noise

- Black smoke

- Lack of power

- Vibration at engine stop

- Turbo overspeed, turbo damage


CONFIRMATION DRIVING PATTERN

P0122, P0123
DTC Detection Drive Pattern Ignition switch ON for 3 seconds

MONITOR DESCRIPTION

When the output voltage of the throttle position sensor deviates from the normal operating range (between 0.2 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

A302636E01
2.104,1.167 2.313,1.052 false 2.094,2.74 2.302,2.625 false 3.313,1 3.469,0.417 3.469,0.417 3.615,0.417 false 4.604,2.656 4.719,3.031 4.719,3.031 4.823,3.031 false 0.146,1.365 1.635,1.781 1.49,0.417 10 false Throttle Position Sensor Output Voltage (V) 2.042,0.625 2.563,0.844 0.521,0.219 10 false Closed 1.99,0.885 2.333,1.063 0.344,0.177 10 false 5.00 1.802,1.115 2.146,1.292 0.344,0.177 10 false 4.80 2,1.365 2.344,1.542 0.344,0.177 10 false 3.49 2,2.406 2.344,2.583 0.344,0.177 10 false 0.69 1.844,2.75 2.188,2.927 0.344,0.177 10 false 0.20 2.677,2.729 3.917,2.948 1.24,0.219 10 false Range of Operation 3.656,0.333 4.552,0.573 0.896,0.24 10 false Stores P0123 3.938,0.604 4.458,0.823 0.521,0.219 10 false Open 4.865,2.948 5.823,3.177 0.958,0.229 10 false Stores P0122 2.281,3.177 2.438,3.344 0.156,0.167 10 false 0 4.083,3.177 4.396,3.344 0.313,0.167 10 false 70° 2.656,3.385 4.531,3.635 1.875,0.25 10 false Throttle Valve Opening Angle

WIRING DIAGRAM

A221590E12
0.74,2.875 2.313,3.059 1.573,0.184 10 Throttle Position Sensor 0.74,2.693 1.059,2.874 0.319,0.180 10 C9 5.441,2.707 5.867,2.877 0.427,0.170 10 C166 5.441,2.889 5.847,3.045 0.406,0.156 10 ECM 5.469,0.928 5.876,1.110 0.408,0.182 10 VCVL 5.469,1.418 5.784,1.609 0.316,0.191 10 VLU 5.469,1.867 5.888,2.037 0.420,0.170 10 EVLU 5.199,0.921 5.372,1.077 0.173,0.156 10 14 5.258,1.404 5.415,1.557 0.157,0.152 10 8 5.262,1.86 5.385,2.002 0.123,0.142 10 2 1.864,1.005 2.083,1.161 0.218,0.156 10 VC 1.794,1.495 2.096,1.644 0.302,0.149 10 VTA 1.878,1.944 2.076,2.107 0.198,0.163 10 E2 2.194,0.921 2.295,1.077 0.101,0.156 10 1 2.194,1.397 2.295,1.553 0.101,0.156 10 3 2.194,1.86 2.295,2.016 0.101,0.156 10 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C9-1 (VC) - C166-14 (VCVL) Always Below 1 Ω
C9-3 (VTA) - C166-8 (VLU) Always Below 1 Ω
C9-2 (E2) - C166-2 (EVLU) Always Below 1 Ω
C9-1 (VC) or C166-14 (VCVL) - Body ground Always 10 kΩ or higher
C9-3 (VTA) or C166-8 (VLU) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
C129053C03
0.75,1.125 1.063,1.354 0.313,0.229 1.26,1.583 1.458,1.26 true 1.76,1.25 1.99,1.594 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.823,1.156 1.073,1.333 0.25,0.177 10 false C9 1.094,1.625 1.406,1.823 0.313,0.198 10 false VC 2.01,1.615 2.271,1.813 0.26,0.198 10 false E2
*a Front view of wire harness connector
(to Throttle Position Sensor)


Disconnect the throttle position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C9-1 (VC) - C9-2 (E2) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the throttle position sensor connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE DIESEL THROTTLE BODY ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE DIESEL THROTTLE BODY ASSEMBLY

Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (ACTUAL THROTTLE POSITION)
4.READ VALUE USING GTS (ACTUAL THROTTLE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Enter the following menus: Powertrain / Engine / Data List / Actual Throttle Position.

Powertrain > Engine > Data List
Tester Display
Actual Throttle Position
50003 61 406

e.

Check the movement of the throttle valve when idling the engine after starting it and when the ignition switch is ON.

OK:
Condition GTS Display
Ignition switch ON -5 to 5%
Idling 0 to 93%



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 3 seconds.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END