The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail injection system is controlled.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0335 | Crankshaft Position Sensor "A" Circuit | When the following condition is met (for 5 seconds during cranking or 0.5 seconds during engine start) (1 trip detection logic):
No crankshaft position sensor signal is sent to the ECM while cranking. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
No. 1 crankshaft position sensor plate (crankshaft) ·
ECM |
Comes on | DTC stored |
| P0339 | Crankshaft Position Sensor "A" Circuit Intermittent | No crankshaft position sensor signal is input to the ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):
(a) Engine speed is 1000 rpm or more. (b) STA signal is off. (c) 3 seconds or more have elapsed after STA signal is switched from on to off. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
No. 1 crankshaft position sensor plate (crankshaft) ·
Camshaft timing pulley ·
ECM |
- | DTC stored |
| DTC No. | Data List |
|---|---|
| P0335 | Engine Speed |
| P0339 |
If DTC P0335 and/or P0339 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
| DTC Detection Drive Pattern | Crank or start engine |
| DTC Detection Drive Pattern | Engine running at 1000 rpm or more with vehicle stationary |
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.
A DTC is also stored when the ground of a shielded wire is faulty.
Inspect the crankshaft position sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSTALLATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C6-1 (NE+) - C163-7 (NE+) | Always | Below 1 Ω |
| C6-2 (NE-) - C163-8 (NE-) | Always | Below 1 Ω |
| C6-1 (NE+) or C163-7 (NE+) - Body ground | Always | 10 kΩ or higher |
| C6-2 (NE-) or C163-8 (NE-) - Body ground | Always | 10 kΩ or higher |
Reconnect the crankshaft position sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the sensor installation.
Sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the teeth of the sensor plate.
The sensor plate teeth do not have any cracks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the teeth of the camshaft timing pulley.
The sensor plate teeth do not have any cracks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the crankshaft position sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Securely reinstall the sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 1 crankshaft position sensor plate.
Click hereEngine / Hybrid System>1KD-FTV ENGINE MECHANICAL>ENGINE UNIT(w/ Glow Plug Controller)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Replace the camshaft timing pulley.
Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP(w/ Glow Plug Controller)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Start the engine and run it at 1000 rpm or more for 5 seconds or more.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT