Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal position sensor.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal position sensor.

In the accelerator pedal position sensor, the voltage applied to terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM determines the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.

A303024E01
0.823,2.26 0.656,1.031 0.656,1.031 0.802,1.031 false 0.854,2.844 0.969,1.26 0.969,1.26 1.094,1.26 false 1.01,2.573 1.125,1.469 1.125,1.469 1.229,1.469 false 0.625,3.51 0.49,3.51 0.49,3.51 0.844,3.135 false 4.042,0.948 4.333,1.927 false 4.198,1.969 4.333,2.031 false 4.208,2.156 4.333,2.198 false 4.208,2.354 4.333,2.24 false 4.208,2.573 4.333,2.417 false 4.188,2.927 4.344,2.927 false 4.198,3.135 4.354,3.135 false 1.135,1.156 2.052,1.354 0.917,0.198 10 false No. 2 IC 1.26,1.396 2.177,1.594 0.917,0.198 10 false No. 1 IC 2.688,1.406 3.125,1.646 0.438,0.24 10 false ECM 0.865,0.958 1.698,1.177 0.833,0.219 10 false Magnet 0.667,3.438 1.24,3.635 0.573,0.198 10 false Magnet 2.063,1.75 2.5,1.99 0.438,0.24 10 false VPA 2.063,2.094 2.5,2.333 0.438,0.24 10 false EPA 2.073,2.406 2.51,2.646 0.438,0.24 10 false VCPA 2.063,2.708 2.5,2.948 0.438,0.24 10 false VPA2 2.063,3.031 2.5,3.271 0.438,0.24 10 false EPA2 2.063,3.344 2.5,3.583 0.438,0.24 10 false VCP2 0.125,3.844 1.938,4.094 1.813,0.25 10 false Accelerator Pedal Sensor 1.875,0.833 4.01,1.292 2.135,0.458 10 false Accelerator Pedal Position Sensor Output Voltage (V) 4.302,1.521 4.563,1.729 0.26,0.208 10 false *1 5.844,1.542 6.104,1.75 0.26,0.208 10 false *2 3.906,1.875 4.281,2.073 0.375,0.198 10 false 4.55 3.844,2.073 4.219,2.271 0.375,0.198 10 false 3.988 3.844,2.51 4.219,2.708 0.375,0.198 10 false 3.188 3.99,2.844 4.365,3.042 0.375,0.198 10 false 1.6 3.99,3.063 4.365,3.26 0.375,0.198 10 false 0.8 4.417,3.365 4.792,3.563 0.375,0.198 10 false 0.29 4.292,3.615 4.667,3.813 0.375,0.198 10 false 0 5.771,3.625 6.146,3.823 0.375,0.198 10 false 15.9 4.708,3.625 5.656,3.865 0.948,0.24 10 false Usable Range 3.917,2.281 4.292,2.479 0.375,0.198 10 false 3.75 4.333,4.063 6.219,4.313 1.885,0.25 10 false Accelerator Pedal Angle (°) 4.333,4.354 6.76,4.615 2.427,0.26 10 false *1: Accelerator Pedal Fully Released 4.333,4.583 6.729,4.854 2.396,0.271 10 false *2: Accelerator Pedal Fully Depressed

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V and VPA2 is more than 2.7 deg, or VPA is higher than 4.8 V.
·

Accelerator pedal position sensor

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA is below 0.4 V.
(b) VPA2 is more than 2.7 deg.
·

Accelerator pedal position sensor

·

Open in VCPA circuit

·

VPA circuit open or shorted to ground

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input Condition (a) continues for 2.0 seconds (1 trip detection logic):
(a) VPA is higher than 4.8 V.
·

Accelerator pedal position sensor

·

Open in EPA circuit

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V and VPA is more than 2.7 deg, or VPA2 is higher than 4.8 V and VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal position sensor

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA2 is below 1.2 V.
(b) VPA is more than 2.7 deg.
·

Accelerator pedal position sensor

·

Open in VCP2 circuit

·

VPA2 circuit open or shorted to ground

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) VPA2 is higher than 4.8 V.
(b) VPA is higher than 0.4 V but below 3.45 V.
·

Accelerator pedal position sensor

·

Open in EPA2 circuit

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Conditions (a) or (b) continue for 2.0 seconds (1 trip detection logic):
(a) The difference between VPA and VPA2 is less than 0.02 V.
(b) VPA is below 0.4 V and VPA2 is below 1.2 V.
·

VPA and VPA2 circuits are short-circuited

·

Accelerator pedal position sensor

·

Accelerator pedal sensor assembly

·

Accelerator pedal rod (arm) deformed

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2120
·

Accel Position

·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %


P2122
P2123
P2125
P2127
P2128
P2138

CONFIRMATION DRIVING PATTERN

P2120, P2122, P2123, P2125, P2127, P2128, P2138
DTC Detection Drive Pattern Ignition switch ON
·

Accelerator pedal fully released for 3 seconds

·

Accelerator pedal depressed partway for 3 seconds

·

Accelerator pedal fully depressed for 3 seconds



WIRING DIAGRAM

A276476E07
0.271,3.229 3.125,3.438 2.854,0.208 10 false Accelerator Pedal Position Sensor 5.583,1.281 6.042,1.49 0.458,0.208 10 false VCPA 5.323,1.208 5.427,1.417 0.104,0.208 10 false 6 5.313,0.365 5.417,0.573 0.104,0.208 10 false 2 5.333,2.469 5.427,2.677 0.094,0.208 10 false 4 5.302,0.792 5.406,1 0.104,0.208 10 false 5 5.323,1.635 5.417,1.844 0.094,0.208 10 false 1 5.323,2.052 5.427,2.26 0.104,0.208 10 false 3 5.594,0.448 5.99,0.656 0.396,0.208 10 false VPA 5.594,0.875 6.042,1.083 0.448,0.208 10 false EPA 5.594,2.542 6.042,2.75 0.448,0.208 10 false VCP2 5.594,1.708 6.031,1.917 0.438,0.208 10 false VPA2 5.594,2.115 6.177,2.323 0.583,0.208 10 false EPA2 1.49,1.385 2.031,1.552 0.542,0.167 10 false VCPA 1.583,0.542 2.063,0.74 0.479,0.198 10 false VPA 1.583,0.958 2.021,1.177 0.438,0.219 10 false EPA 1.5,2.625 1.948,2.833 0.448,0.208 10 false VCP2 1.51,1.792 1.948,2 0.438,0.208 10 false VPA2 1.51,2.208 2.052,2.406 0.542,0.198 10 false EPA2 1.979,1.49 2.188,1.698 0.208,0.208 10 false 4 1.969,0.635 2.177,0.844 0.208,0.208 10 false 6 1.979,1.063 2.188,1.271 0.208,0.208 10 false 5 1.979,2.74 2.188,2.948 0.208,0.208 10 false 1 1.979,1.896 2.188,2.104 0.208,0.208 10 false 3 1.979,2.333 2.188,2.542 0.208,0.208 10 false 2 5.99,3.063 6.385,3.26 0.396,0.198 10 false ECM 0.26,3.052 0.563,3.24 0.302,0.188 10 false G6 5.177,0.531 5.573,0.708 0.396,0.177 10 false G157 5.177,1.802 5.656,1.979 0.479,0.177 10 false G157 5.167,0.948 5.573,1.125 0.406,0.177 10 false G156 5.167,1.375 5.573,1.552 0.406,0.177 10 false G156 5.177,2.219 5.646,2.406 0.469,0.188 10 false G156 5.177,2.646 5.74,2.833 0.563,0.188 10 false G156

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

Powertrain > Engine > Data List
Tester Display
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
50003 61 75,76

d.
C129061C03
0.833,1.594 1.042,1.802 0.208,0.208 10 false *a 0.271,0.323 0.479,0.531 0.208,0.208 10 false *1 2.24,1.594 2.5,1.802 0.26,0.208 10 false *b
*1 Accelerator Pedal Assembly
*a Depressed
*b Released


Read the values.

Standard:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%


Result:
Result Proceed to
NG A
OK B




A

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

B

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-1 (VCP2) - G156-4 (VCP2) Always Below 1 Ω
G6-2 (EPA2) - G156-3 (EPA2) Always Below 1 Ω
G6-3 (VPA2) - G157-1 (VPA2) Always Below 1 Ω
G6-4 (VCPA) - G156-6 (VCPA) Always Below 1 Ω
G6-5 (EPA) - G156-5 (EPA) Always Below 1 Ω
G6-6 (VPA) - G157-2 (VPA) Always Below 1 Ω
G6-1 (VCP2) or G156-4 (VCP2) - Body ground Always 10 kΩ or higher
G6-3 (VPA2) or G157-1 (VPA2) - Body ground Always 10 kΩ or higher
G6-4 (VCPA) or G156-6 (VCPA) - Body ground Always 10 kΩ or higher
G6-6 (VPA) or G157-2 (VPA) - Body ground Always 10 kΩ or higher



d.

Reconnect the accelerator pedal position sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
a.

Disconnect the accelerator pedal position sensor connector.


b.
A251332C02
0.542,1.104 0.927,1.344 0.385,0.24 0.792,1.792 1.323,1.292 true 1.292,1.792 1.5,1.292 true 1.958,1.854 1.833,1.281 true 2.552,1.854 1.979,1.281 true 0.198,0.24 0.51,0.438 0.313,0.198 10 false *a 0.635,1.135 0.948,1.333 0.313,0.198 10 false G6 0.531,1.823 1.021,2.021 0.49,0.198 10 false VCP2 1.125,1.833 1.573,2.031 0.448,0.198 10 false EPA2 1.802,1.844 2.292,2.031 0.49,0.188 10 false VCPA 2.479,1.854 2.792,2.052 0.313,0.198 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Position Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G6-4 (VCPA) - G6-5 (EPA) Ignition switch ON 4.5 to 5.5 V
G6-1 (VCP2) - G6-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the accelerator pedal position sensor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

NG

7.REPLACE ECM
4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off and leave the vehicle for 30 seconds.


d.

Turn the ignition switch to ON.


e.

Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.


f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED