Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the EGR valve angle. The EGR valve angle detected by the sensor is sent to the ECM as feedback. The ECM then regulates the EGR valve angle in accordance with engine running conditions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low EGR valve position sensor output voltage is less than 0.2 V for 2 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

Electric EGR control valve assembly (EGR valve position sensor)

·

ECM


Comes on DTC stored
P0406 Exhaust Gas Recirculation Sensor "A" Circuit High EGR valve position sensor output voltage is higher than 4.8 V for 2 seconds.
(1 trip detection logic)
·

Open or short in EGR valve position sensor circuit

·

Electric EGR control valve assembly (EGR valve position sensor)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P0405, P0406
DTC Detection Drive Pattern Ignition switch ON for 5 seconds or more

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.2 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the electric EGR control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C120-3 (VC) - C166-13 (VCEG) Always Below 1 Ω
C120-2 (VTA) - C166-7 (EGRA) Always Below 1 Ω
C120-1 (E2) - C166-1 (EEGL) Always Below 1 Ω
C120-3 (VC) or C166-13 (VCEG) - Body ground Always 10 kΩ or higher
C120-2 (VTA) or C166-7 (EGRA) - Body ground Always 10 kΩ or higher



d.

Reconnect the electric EGR control valve assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
A242722C02
0.24,1.052 0.646,1.313 0.406,0.26 1.021,1.792 1.198,1.281 true 1.885,1.802 1.719,1.292 true 0.438,0.188 0.75,0.385 0.313,0.198 10 false *a 0.271,1.094 0.646,1.281 0.375,0.188 10 false C120 0.917,1.813 1.229,2.01 0.313,0.198 10 false E2 1.833,1.813 2.146,2.01 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Electric EGR Valve Assembly)


Disconnect the electric EGR control valve assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C120-3 (VC) - C120-1 (E2) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the electric EGR control valve assembly connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1KD-FTV EMISSION CONTROL>EGR VALVE(w/ Glow Plug Controller)>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (P0405 OR P0406)
4.CHECK WHETHER DTC OUTPUT RECURS (P0405 OR P0406)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 5 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.

OK:

DTC is not output again.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE ECM
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch to ON for 5 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END