Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0488  Exhaust Gas Recirculation Throttle Position Control Range / Performance  


DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance Target and actual opening angle of the throttle valve differs for approximately 20 seconds.
(1 trip detection logic)
The throttle motor activation duty exceeds the threshold for 0.5 seconds a certain number of times (40 seconds or more).
(1 trip detection logic)
·

Throttle valve stuck

·

Throttle valve does not move smoothly

·

Open or short in throttle control motor circuit

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0488
·

Throttle Motor Duty

·

Actual Throttle Position



Reference
Condition Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm Throttle valve opening angle varies smoothly

CONFIRMATION DRIVING PATTERN

P0488
DTC Detection Drive Pattern Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.

A128641E15
4.594,2.156 4.719,1.833 false 4.594,2.896 4.719,2.573 false 4.615,3.646 4.74,3.333 false 4.729,4.115 4.604,3.802 false 5.333,5.26 5.156,5.042 false 3.333,5.375 3.094,5.198 false 0.375,5.458 1.677,5.844 1.302,0.385 10 false Duty Ratio Malfunction Counter 0.125,0.156 1.906,0.365 1.781,0.208 10 false Malfunction Detection: 0.323,1.281 1.604,1.646 1.281,0.365 10 false Throttle Valve Target Opening Angle 0.281,2.719 1.229,2.917 0.948,0.198 10 false Throttle Valve 0.958,4.146 1.698,4.365 0.74,0.219 10 false Duty Ratio 4.76,1.729 5.354,1.927 0.594,0.198 10 false Normal 4.781,2.479 5.531,2.677 0.75,0.198 10 false Abnormal 4.781,4.063 5.375,4.26 0.594,0.198 10 false Normal 4.802,3.219 5.552,3.417 0.75,0.198 10 false Abnormal 5.938,0.594 6.385,0.792 0.448,0.198 10 false Open 5.938,1.354 6.417,1.552 0.479,0.198 10 false Close 5.927,2.073 6.375,2.271 0.448,0.198 10 false Open 5.938,2.823 6.417,3.021 0.479,0.198 10 false Close 5.938,3.552 6.448,3.76 0.51,0.208 10 false 100% 5.948,4.333 6.292,4.531 0.344,0.198 10 false 0% 3.396,5.323 4.813,5.531 1.417,0.208 10 false Stores P0488 5.354,5.281 6.146,5.49 0.792,0.208 10 false Threshold 3.563,6.313 3.969,6.521 0.406,0.208 10 false Time 0.281,2.906 1.896,3.271 1.615,0.365 10 false Actual Opening Angle

WIRING DIAGRAM

A276470E07
2.885,1.74 4.333,1.917 1.448,0.177 10 false Throttle Control Motor 2.031,3.542 2.448,3.729 0.417,0.188 10 false MAIN 2.854,3.094 3.24,3.271 0.385,0.177 10 false EFI 2.927,0.542 3.521,0.75 0.594,0.208 10 false RSC 3.469,0.885 3.948,1.083 0.479,0.198 10 false RSO 3.917,3.406 4.708,3.667 0.792,0.26 10 false BATT P/I 3.958,3.896 4.656,4.125 0.698,0.229 10 false Battery 6.135,4.521 6.688,4.708 0.552,0.188 10 false ECM 5.958,0.885 6.375,1.063 0.417,0.177 10 false LUSL 5.958,2.042 6.385,2.219 0.427,0.177 10 false MREL 5.958,2.615 6.167,2.802 0.208,0.188 10 false E1 2.927,1.229 3.333,1.427 0.406,0.198 10 false B 5.552,0.896 6.01,1.073 0.458,0.177 10 false C163 5.552,2.625 6.01,2.802 0.458,0.177 10 false C164 2.896,1.604 3.208,1.771 0.313,0.167 10 false C15 5.542,2.031 6.031,2.208 0.49,0.177 10 false G156 3.865,0.802 4.063,1.01 0.198,0.208 10 false 1 3.063,3.365 3.323,3.615 0.26,0.25 10 false 1 3.49,3.042 3.792,3.281 0.302,0.24 10 false 1 1.344,3.052 1.698,3.25 0.354,0.198 10 false 5 2.75,1.156 3.052,1.344 0.302,0.188 10 false 2 1.344,2.438 1.604,2.615 0.26,0.177 10 false 2 2.813,3.365 3.073,3.583 0.26,0.219 10 false 2 2.75,0.448 2.979,0.656 0.229,0.208 10 false 3 3.5,2.448 3.833,2.688 0.333,0.24 10 false 3 5.635,0.708 5.885,0.885 0.25,0.177 10 false 17 5.625,1.854 5.823,2.031 0.198,0.177 10 false 11 5.667,2.458 5.792,2.635 0.125,0.177 10 false 6 3.458,2.635 3.958,2.875 0.5,0.24 10 false 1J 1.292,2.635 1.667,2.844 0.375,0.208 10 false 1J 1.292,3.25 1.667,3.427 0.375,0.177 10 false 1J 3.458,3.24 3.802,3.448 0.344,0.208 10 false 1H 0.719,1.094 1.49,1.292 0.771,0.198 10 false EFI NO. 2 1.667,3.99 3.385,4.188 1.719,0.198 10 false No. 1 Integration Relay 0.833,1.396 1.094,1.635 0.26,0.24 10 false 1 1.104,1.396 1.448,1.656 0.344,0.26 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:
·

Although the DTC title is Exhaust Gas Recirculation Throttle Position Control Range / Performance, these DTCs relate to the throttle valve

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Diesel Throttle Target Angle.

Powertrain > Engine > Active Test
Tester Display
Diesel Throttle Target Angle
50004 61 161

d.

When changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0% continuously, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



Result:
Proceed to
OK
NG



OK

5.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
2.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)
a.
A129055C03
0.51,1.24 0.938,1.521 0.427,0.281 1.708,1.896 1.708,1.479 true 0.604,1.292 0.917,1.49 0.313,0.198 10 false C15 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.667,1.906 1.979,2.104 0.313,0.198 10 false B
*a Front view of wire harness connector
(to Throttle Control Motor)


Disconnect the throttle control motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C15-2 (B) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the throttle control motor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Disconnect the throttle control motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C15-3 (RSC) - Body ground Always Below 1 Ω



c.

Reconnect the throttle control motor connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
a.

Disconnect the throttle control motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C15-1 (RSO) - C163-17 (LUSL) Always Below 1 Ω
C15-1 (RSO) or C163-17 (LUSL) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle control motor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.REMOVE DEPOSIT (DIESEL THROTTLE BODY ASSEMBLY)
a.

Visually check for deposits in the diesel throttle body. If there are deposits, clean the diesel throttle body.


Result:
Proceed to
NEXT



NEXT

6.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
6.PERFORM ACTIVE TEST USING GTS (DIESEL THROTTLE TARGET ANGLE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Diesel Throttle Target Angle.

Powertrain > Engine > Active Test
Tester Display
Diesel Throttle Target Angle
50004 61 161

d.

When changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0% continuously, check that Actual Throttle Position smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



Result:
Proceed to
OK
NG



OK

11.CHECK WHETHER DTC OUTPUT RECURS

NG

10.REPLACE DIESEL THROTTLE BODY ASSEMBLY
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - NO. 1 INTEGRATION RELAY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0488.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END

10.REPLACE DIESEL THROTTLE BODY ASSEMBLY

Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS
11.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Start the engine.


e.

Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Result Proceed to
P0488 is output A
No DTC is output B




A

12.REPLACE ECM

B

END

12.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED