Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM J

2TR-FBE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, current flows from terminal ST1 of the ignition switch to the starter relay coil and current also flows to terminal STA of the ECM (STA signal).

When the STA signal and NE signal are input to the ECM, Tr is turned on, current flows to the coil of the circuit opening relay, the relay switches on, power is supplied to the fuel pump and the fuel pump operates.

While the NE signal is generated (engine running), the ECM keeps Tr on (circuit opening relay on) and the fuel pump continues operating.

WIRING DIAGRAM

A262788
6.063,6.563 6.458,6.771 0.396,0.208 10 false NE- 0.76,0.927 1.25,1.156 0.49,0.229 10 false AM2 6.063,6 6.458,6.229 0.396,0.229 10 false NE+ 2.188,2.115 2.573,2.365 0.385,0.25 10 false EFI 1.958,0.615 2.427,0.875 0.469,0.26 10 false AM2 0.667,2.135 1.354,2.385 0.688,0.25 10 false BATT P/I 6.302,6.979 6.781,7.25 0.479,0.271 10 false ECM 6.063,2.385 6.583,2.604 0.521,0.219 10 false MREL 6.063,5.448 6.469,5.708 0.406,0.26 10 false STA 6.063,4.792 6.365,5.021 0.302,0.229 10 false FC 1.75,0.615 2.01,0.865 0.26,0.25 10 false 5 5.604,2.385 6.031,2.635 0.427,0.25 10 false G146 5.677,2.198 5.938,2.417 0.26,0.219 10 false 12 4.031,0.917 4.354,1.104 0.323,0.188 10 false IGN 2.958,0.615 3.188,0.865 0.229,0.25 10 false 6 0.667,6.563 1.333,6.833 0.667,0.271 10 false Battery 1.552,3.281 1.729,3.469 0.177,0.188 10 false 8 1.51,3.469 1.802,3.698 0.292,0.229 10 false 1J 3.083,4.469 4.375,4.771 1.292,0.302 10 false Integration Relay 1.625,1.188 3.24,1.469 1.615,0.281 10 false Ignition Switch Assembly 1.625,1.042 1.927,1.281 0.302,0.24 10 false G9 2.594,0.615 2.917,0.906 0.323,0.292 10 false IG2 1.552,1.76 1.771,1.979 0.219,0.219 10 false 1 1.5,1.948 1.771,2.146 0.271,0.198 10 false 1H 1.552,2.208 1.833,2.49 0.281,0.281 10 false 3 1.521,2.396 1.823,2.625 0.302,0.229 10 false 1J 4.135,2.198 4.323,2.427 0.188,0.229 10 false 2 4.104,2.396 4.406,2.635 0.302,0.24 10 false 1J 4.135,3.667 4.313,3.854 0.177,0.188 10 false 6 4.104,3.865 4.375,4.073 0.271,0.208 10 false 1J 1.552,3.677 1.729,3.865 0.177,0.188 10 false 7 1.51,3.854 1.823,4.177 0.313,0.323 10 false 1J 5.604,4.938 6.021,5.188 0.417,0.25 10 false G146 5.698,4.75 5.917,4.969 0.219,0.219 10 false 25 5.615,5.448 6.063,5.698 0.448,0.25 10 false G146 5.74,5.271 5.958,5.521 0.219,0.25 10 false 8 5.646,6 6,6.219 0.354,0.219 10 false C96 5.688,5.813 5.917,6.021 0.229,0.208 10 false 12 5.656,6.542 5.99,6.781 0.333,0.24 10 false C96 5.729,6.344 5.948,6.573 0.219,0.229 10 false 5 3.021,2.688 3.469,2.938 0.448,0.25 10 false MAIN 1.375,6.26 2.198,6.49 0.823,0.229 10 false Fuel Pump 2.969,4.135 3.51,4.396 0.542,0.26 10 false C/OPN 3.833,5.396 5.104,5.719 1.271,0.323 10 false from Starter Circuit 3.5,5.979 5.063,6.365 1.563,0.385 10 false from Crankshaft Position Sensor Circuit 1.271,5.271 1.469,5.5 0.198,0.229 10 false 4 2.094,5.271 2.313,5.51 0.219,0.24 10 false 5 1.375,6.083 1.635,6.271 0.26,0.188 10 false L4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE C/OPN RELAY)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operation sound occurs when performing the Active Test on the tester.

OK:

Fuel pump operating sound occurs.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT NO. 1 INTEGRATION RELAY (C/OPN AND MAIN)
2.INSPECT NO. 1 INTEGRATION RELAY (C/OPN AND MAIN)
a.

Inspect the No. 1 integration relay (C/OPN).

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


b.

Inspect the integration relay (MAIN).

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [C/OPN] - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (C/OPN AND MAIN)

3.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [C/OPN] - ECM)
a.

Disconnect the ECM connector.


b.

Remove the integration relay (C/OPN) from the engine room relay block.


c.

Disconnect the integration relay connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1J-7 - G146-25 (FC) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1J-7 or G146-25 (FC) - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the integration relay connector.


g.

Reinstall the integration relay (C/OPN).


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - INTEGRATION RELAY [C/OPN])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [C/OPN] - ECM)

4.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - INTEGRATION RELAY [C/OPN])
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the integration relay connector.


c.

Disconnect the ignition switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G9-6 (IG2) - 1J-6 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G9-6 (IG2) or 1J-6 - Body ground Always 10 kΩ or higher



e.

Reconnect the ignition switch assembly connector.


f.

Reconnect the integration relay connector.


g.

Reinstall the integration relay.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [C/OPN] - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - INTEGRATION RELAY [C/OPN])

5.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY [C/OPN] - FUEL PUMP)
a.

Disconnect the fuel pump connector.


b.

Remove the integration relay from the engine room relay block.


c.

Disconnect the integration relay connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1J-8 - L4-4 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1J-8 or L4-4 - Body ground Always 10 kΩ or higher



e.

Reconnect the integration relay connector.


f.

Reinstall the integration relay.


g.

Reconnect the fuel pump connector.


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY [C/OPN] - FUEL PUMP)

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L4-5 - Body ground Always Below 1 Ω



c.

Reconnect the fuel pump connector.


Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PUMP - BODY GROUND)

7.INSPECT FUEL PUMP

Result:
Proceed to
OK
NG



OK

8.CHECK ECM POWER SOURCE CIRCUIT

NG

8.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT