Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

Flat-type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 6 kHz and 15 kHz.

The knock sensor is fitted onto the engine block to detect engine knocking.

The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
·

Short in knock sensor circuit

·

Knock sensor

·

ECM


Comes on DTC stored
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) The output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
·

Open in knock sensor circuit

·

Knock sensor

·

ECM


Comes on DTC stored

HINT:

When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A150243
0.333,0.552 1.917,0.771 1.583,0.219 10 false KNK1 Signal Waveform 2.635,1.938 2.99,2.135 0.354,0.198 10 false GND 2.5,1.094 3.063,1.292 0.563,0.198 10 false 1 V/DIV. 1,2.865 1.844,3.063 0.844,0.198 10 false 1 ms./DIV.

The correct waveform is as shown.

Item Content
ECM Terminal Name KNK1 - EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after engine warmed up

WIRING DIAGRAM

A209226
1.399,1.528 1.65,1.701 0.251,0.173 10 S1 1.348,1.224 1.489,1.398 0.141,0.173 10 1 2.352,1.224 2.493,1.398 0.141,0.173 10 2 1.399,1.665 2.53,1.876 1.131,0.211 10 Knock Sensor 5.866,3.012 6.205,3.185 0.339,0.174 10 C95 5.866,3.157 6.281,3.33 0.416,0.174 10 ECM 5.276,1.032 5.46,1.205 0.184,0.174 10 6 5.489,1.032 5.877,1.205 0.388,0.174 10 KNK1 5.489,1.858 5.928,2.032 0.439,0.174 10 EKNK 5.276,1.858 5.469,2.032 0.193,0.174 10 5 3.599,2.384 4.299,2.558 0.7,0.174 10 Shielded

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (KNOCK FEEDBACK VALUE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Knock Feedback Value.

Powertrain > Engine and ECT > Data List
Tester Display
Knock Feedback Value
50003 234 192

f.

Read the values displayed on the tester while the vehicle is being driven.

OK:

The values change.


HINT:
Malfunction does not occur Knock feedback values change
Malfunction occurs Knock feedback values do not change

The Knock Feedback Value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ECM (KNK1 VOLTAGE)
2.INSPECT ECM (KNK1 VOLTAGE)
a.
A200903
0.531,0.938 0.844,1.156 0.313,0.219 0.083,0.073 0.427,0.344 0.344,0.271 10 false *a 0.604,0.969 0.948,1.24 0.344,0.271 10 false S1
*a Front view of wire harness connector
(to Knock Sensor)


Disconnect the knock sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S1-2 - S1-1 Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the knock sensor connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT KNOCK SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
3.INSPECT KNOCK SENSOR

Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
a.

Disconnect the knock sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
S1-2 - C95-6 (KNK1) Always Below 1 Ω
S1-1 - C95-5 (EKNK) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
S1-2 or C95-6 (KNK1) - Body ground Always 10 kΩ or higher
S1-1 or C95-5 (EKNK) - Body ground Always 10 kΩ or higher



d.

Reconnect the knock sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - KNOCK SENSOR)