Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of evaporated fuel is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0443 Evaporative Emission Control System Purge Control Valve Circuit The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1-trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A304481
0.927,0.844 1.083,1.042 0.156,0.198 10 false 1 0.885,1.031 1.115,1.25 0.229,0.219 10 false 1H 1.344,1.188 1.615,1.406 0.271,0.219 10 false EFI 1.979,1.74 2.385,1.938 0.406,0.198 10 false MAIN 1.51,1.813 1.781,2.031 0.271,0.219 10 false 1J 1.292,1.813 1.448,2.01 0.156,0.198 10 false 3 2.656,1.385 2.927,1.604 0.271,0.219 10 false 1J 2.667,1.031 2.938,1.25 0.271,0.219 10 false 1J 2.688,0.854 2.844,1.052 0.156,0.198 10 false 5 2.688,1.208 2.844,1.406 0.156,0.198 10 false 2 1.635,2.031 2.74,2.292 1.104,0.26 10 false Integration Relay 0.635,2.885 1.26,3.104 0.625,0.219 10 false BATT P/I 0.781,3.885 1.375,4.146 0.594,0.26 10 false Battery 4,0.906 4.156,1.104 0.156,0.198 10 false 2 4.802,0.906 4.958,1.104 0.156,0.198 10 false 1 5.51,0.844 5.781,1.063 0.271,0.219 10 false 19 5.469,1.021 5.75,1.26 0.281,0.24 10 false C97 5.833,1.021 6.26,1.313 0.427,0.292 10 false PRG 5.375,3.063 5.771,3.302 0.396,0.24 10 false G146 5.469,2.875 5.74,3.094 0.271,0.219 10 false 12 5.823,3.073 6.25,3.365 0.427,0.292 10 false MREL 6.115,3.823 6.542,4.115 0.427,0.292 10 false ECM 4.146,1.354 4.5,1.677 0.354,0.323 10 false C69 4.156,1.531 4.906,1.771 0.75,0.24 10 false Purge VSV

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A080362
0.677,1.729 1.594,1.979 0.917,0.25 10 false Suction of air 2.24,1.74 3.333,1.979 1.094,0.24 10 false No suction of air 0.729,0.375 1.646,0.625 0.917,0.25 10 false VSV ON 2.333,0.365 3.25,0.615 0.917,0.25 10 false VSV OFF

Connect the intelligent tester to the DLC3.


b.

Disconnect the vacuum hose of the charcoal canister from the purge VSV.


c.

Start the engine.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

f.

When the purge VSV is operated using the intelligent tester, check whether the purge VSV applies suction to your finger.

OK:
Tester Operation Specified Condition
VSV is ON Suction applied
VSV is OFF No suction applied



g.

Reconnect the vacuum hose of the charcoal canister to the purge VSV.


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

NG

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
a.
A241839
0.74,1.208 1.094,1.458 0.354,0.25 0.146,0.094 0.531,0.333 0.385,0.24 10 false *a 0.792,1.25 1.177,1.49 0.385,0.24 10 false C69
*a Front view of wire harness connector
(to Purge VSV)


Disconnect the purge VSV connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C69-2 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the purge VSV connector.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY [MAIN RELAY])
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C69-1 - C97-19 (PRG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C69-1 or C97-19 (PRG) - Body ground Always 10 kΩ or higher



d.

Reconnect the purge VSV connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PURGE VSV - ECM)

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY [MAIN RELAY])
a.

Disconnect the purge VSV connector.


b.

Remove the integration relay (MAIN relay) from the engine room relay block and disconnect the integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C69-2 - 1J-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C69-2 or 1J-5 - Body ground Always 10 kΩ or higher



d.

Reconnect the integration relay connector.


e.

Reinstall the integration relay.


f.

Reconnect the purge VSV connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PURGE VSV - INTEGRATION RELAY [MAIN RELAY])