Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed and released are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) The ignition switch is ON.
(b) The brake pedal is released.
(c) The STP signal is off when the ST1- signal is off.
·

Open or short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM


- DTC stored

WIRING DIAGRAM

A262775
1.729,0.698 2.052,0.948 0.323,0.25 10 false IG2 1.063,0.698 1.51,0.938 0.448,0.24 10 false AM2 0.469,1.406 0.854,1.625 0.385,0.219 10 false AM2 2.74,0.958 3.167,1.188 0.427,0.229 10 false IGN 5.219,0.708 5.333,0.896 0.115,0.188 10 false 4 3.76,0.708 3.875,0.896 0.115,0.188 10 false 3 3.771,1.635 3.885,1.823 0.115,0.188 10 false 2 5.219,1.635 5.333,1.823 0.115,0.188 10 false 1 3.875,2.229 4.323,2.448 0.448,0.219 10 false A24 3.875,2.396 5.677,2.75 1.802,0.354 10 false Stop Light Switch Assembly 6.135,0.813 6.542,1 0.406,0.188 10 false ST1- 6.135,1.76 6.583,1.979 0.448,0.219 10 false STP 5.792,1.563 5.99,1.74 0.198,0.177 10 false 18 5.833,0.625 6.073,0.823 0.24,0.198 10 false 8 6.344,3.094 6.771,3.302 0.427,0.208 10 false ECM 0.875,0.698 1.021,0.885 0.146,0.188 10 false 5 2.063,0.698 2.188,0.885 0.125,0.188 10 false 6 0.938,1.198 1.365,1.438 0.427,0.24 10 false G9 0.948,1.365 2.552,1.615 1.604,0.25 10 false Ignition Switch Assembly 1.635,1.917 1.979,2.146 0.344,0.229 10 false ALT 0.583,2.656 1.219,2.885 0.635,0.229 10 false Battery 2.667,1.927 3.24,2.146 0.573,0.219 10 false STOP 5.719,1.76 6.188,2.021 0.469,0.26 10 false G146 5.729,0.813 6.198,1.042 0.469,0.229 10 false G145

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / All Data / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
A200909
0.729,1.01 1.104,1.26 0.375,0.25 0.094,0.073 0.448,0.375 0.354,0.302 10 false *a 0.802,1.063 1.156,1.365 0.354,0.302 10 false A24
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A24-3 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the stop light switch assembly connector.


Result:
Result
OK
NG



OK

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)
2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
A200909
0.771,0.99 1.135,1.24 0.365,0.25 0.094,0.063 0.531,0.302 0.438,0.24 10 false *a 0.844,1.031 1.281,1.271 0.438,0.24 10 false A24
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 - Body ground Always 11 to 14 V



c.

Reconnect the stop light switch assembly connector.


Result:
Result
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
A072924
2.625,1.083 2.344,0.635 false 2.875,1.083 3.156,0.646 false 2.563,1.333 2.344,1.833 false 2.917,1.333 3.073,1.844 false 0.063,0.042 0.896,0.26 0.833,0.219 10 false Not Pushed 1.271,0.604 2.104,0.823 0.833,0.219 10 false Pushed 3.146,0.458 3.302,0.688 0.156,0.229 10 false 1 2.281,0.458 2.438,0.688 0.156,0.229 10 false 2 2.281,1.865 2.438,2.094 0.156,0.229 10 false 4 3.073,1.865 3.229,2.094 0.156,0.229 10 false 3

Inspect the stop light switch assembly.

i.

Measure the voltage according to the value(s) in the table below.



Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
3 - 4 Pin not pushed 10 kΩ or higher
1 - 2 Pin pushed 10 kΩ or higher
3 - 4 Pin pushed Below 1 Ω


Result:
Proceed to
OK
NG



OK

4.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A262769
0.135,0.25 0.521,0.458 0.385,0.208 0.563,0.25 0.948,0.458 0.385,0.208 0.479,1.604 0.573,0.865 true 0.896,1.573 0.677,0.875 true 0.052,0.031 0.302,0.25 0.25,0.219 10 false *a 0.594,0.271 1,0.49 0.406,0.219 10 false G146 0.167,0.271 0.573,0.49 0.406,0.219 10 false G145 0.198,1.646 0.802,1.927 0.604,0.281 10 false 8 (ST1-) 0.938,1.479 1.542,1.76 0.604,0.281 10 false 18 (STP)
*a Component with harness connected
(ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Operation Specified Condition
G145-8 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
G146-18 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V



d.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A24-3 - G9-6 (IG2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A24-3 or G9-6 (IG2) - Body ground Always 10 kΩ or higher



d.

Reconnect the ignition switch connector.


e.

Reconnect the stop light switch assembly connector.


Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION SWITCH ASSEMBLY)