Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage An open in the ECM back-up power source circuit (1 trip detection logic).
·

Open in back-up power source circuit

·

Battery

·

Battery terminals

·

ECM


Comes on DTC stored

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs and the data stored in the ECM is partly cleared.


WIRING DIAGRAM

A262777
1.26,3.76 1.927,4 0.667,0.24 10 false Battery 2.938,1.604 3.292,1.781 0.354,0.177 10 false EFI 5.448,1.438 5.917,1.74 0.469,0.302 10 false G145 5.583,2.552 5.74,2.698 0.156,0.146 10 false 5 5.5,2.76 5.875,2.99 0.375,0.229 10 false C98 5.552,1.24 5.802,1.448 0.25,0.208 10 false 17 6.146,3.604 6.667,3.927 0.521,0.323 10 false ECM 5.844,1.333 6.323,1.542 0.479,0.208 10 false BATT 5.854,2.75 6.146,2.99 0.292,0.24 10 false E1 1.188,2.5 1.969,2.823 0.781,0.323 10 false BATT P/I

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Disconnect the cable from the positive (+) battery terminal.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G145-17 (BATT) - Positive battery terminal Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G145-17 (BATT) or Positive battery terminal - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the cable to the positive (+) battery terminal.


g.

Reconnect the cable to the negative (-) battery terminal.


Result:
Proceed to
OK
NG



OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - BATTERY)

2.INSPECT BATTERY
a.

Check the battery voltage.

Battery voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT/ DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read the DTCs.

Result:
Result Proceed to
DTC P0560 is output A
DTC is not output B




A

B