Refer to DTC P0412 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0412).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1613 | Secondary Air Injection Driver Malfunction | Condition 1:
Either condition (1) or (2) met: (1) All conditions are met (1 trip detection logic): ·
Either the air pump or the air switching valve is not operating. ·
Diagnostic signal from the air injection control driver is 80%. ·
Battery voltage is 8 V or higher. (2) Both conditions are met (1 trip detection logic): ·
Battery voltage is 8 V or higher. ·
Diagnostic signal from the air injection control driver is abnormal (duty signal other than 0, 20, 40, 80 or 100%). Condition 2: All conditions are met (1 trip detection logic): 1.
Secondary air injection system operating (air switching valve and air pump are on). 2.
Diagnostic signal from the air injection control driver is 0%. 3.
Battery voltage is 8 V or higher. Condition 3: Both conditions are met (1 trip detection logic): 1.
Battery voltage is 8 V or higher. 2.
Diagnostic signal from the air injection control driver is 100%. |
Condition 1:
·
Air injection control driver ·
Open in air injection control driver ground circuit Condition 2: ·
Open in air pump or air switching valve command signal circuit (ECM - air injection control driver) ·
Open in air injection control driver ground circuit ·
Short between diagnostic signal circuit and body ground ·
Air injection control driver ·
ECM Condition 3: ·
Open in diagnostic signal circuit ·
Air injection control driver ·
Open in air injection control driver +B circuit (air injection control driver power source) ·
Short between +B and diagnostic signal circuits ·
Short in air pump or air switching valve command signal circuit (ECM - air injection control driver) ·
Open in air injection control driver ground circuit |
Comes on | DTC stored |
For a short time a after cold engine start, the ECM transmits command signals to the air injection control driver to drive the air pump and air switching valve. The air injection control driver detects open and short circuits according to the voltages at the air injection control driver terminals connected to the air pump and air switching valve, and the circuit voltage of the air injection control driver power source, and transmits diagnostic information as a signal to the ECM.
If the Secondary Air Injection (AIR) system circuit or the air injection control driver itself malfunctions, the air injection control driver sends a malfunction signal (duty signal) as diagnostic information to the ECM (when the system is normal, a system normal signal is sent). The ECM stores the DTC based on the diagnostic information from the air injection control driver.
Example:
The duty ratio of the diagnostic signal from the air injection control driver is 0 or 100% (remains at 0 V or is the same as battery voltage).
The duty ratio of the diagnostic signal from the air injection control driver shows an impossible ratio (other than 0, 20, 40, 80 or 100%).
The air injection control driver outputs the normal signal (normal duty signal: 80%) while the system is not operating.
Refer to DTC P0412 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0412).
Diagnostic information output by the air injection control driver can be confirmed by connecting an oscilloscope to the diagnostic information terminal of the air injection control driver. Reading the waveform while performing the AIR system forced operation provided in the system check allows the possible trouble areas to be narrowed down.
(a) Start the engine and warm it up.
(b) Turn the ignition switch off.
(c) Connect the intelligent tester to the DLC3.
| *a | Component with harness connected
(ECM) |
(d) Connect oscilloscope probes to the AIDI and E1 terminals of the ECM.
(e) Turn the ignition switch to ON and turn the intelligent tester on.
(f) Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.
When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
(g) Start the engine.
(h) Perform the AIR system forced operation while the engine is idling.
(i) Monitor the air injection control driver voltage output (duty ratio signal).
| Item | Content |
|---|---|
| ECM Terminal Name | AIDI - E1 |
| Tester Range | 5 V/DIV., 20 ms/DIV. |
| Condition | Idling |
(j) Turn the ignition switch off.
Secondary Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While AIR system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (Wait or Error).
If Error is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.
Performing Secondary Air Injection Check repeatedly may cause damage to the AIR system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
By using the intelligent tester to perform the Secondary Air Injection Check operation in the system check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
|
If any DTCs other than P1613 are output, troubleshoot those DTCs first. |
|
| P1613 | A |
| P1613 and other DTCs | B |
A
B
| *a | Component with harness connected
(ECM) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.
When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
| Tester Display |
|---|
| Secondary Air Injection Check |
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the AIDI and E1 terminals of the ECM connector when the AIR system is on and off.
Turn the ignition switch off.
Do not perform the system check operation repetitively. It may cause the damage in the system. If it is necessary to repeat the check, leave an interval of several minutes between system check operations.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
| Results | Suspected Trouble Areas | Proceed To |
|---|---|---|
| Fixed at low voltage (1.6 V or less) even when AIR system ON (Air pump ON, ASV OPEN) | ·
Short between air pump or air switching valve command signal circuit and body ground ·
Open in air pump command signal circuit (between ECM and air injection control driver) ·
Open in air switching valve assembly command signal circuit (between ECM and air injection control driver) ·
Open in air injection control driver ground circuit (between air injection control driver and body ground) ·
Diagnostic signal circuit ground short ·
Air injection control driver ·
ECM |
A |
| Fixed at high voltage (12 V or higher) even when AIR system OFF (Air pump OFF, ASV CLOSE) | ·
Open in diagnostic signal circuit (ECM - air injection control driver) ·
Short between +B and diagnostic signal circuits (ECM - air injection control driver) ·
Open in air injection control driver power source circuit ·
Air injection control driver ·
ECM |
B |
| Other than above:
Fluctuating (duty signal other than 20, 40 or 80%) |
·
Air injection control driver ·
Open in air injection control driver ground circuit (between air injection control driver and body ground) |
C |
A
B
C
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G145-19 (AIRP) - C98-5 (E1) | Ignition switch ON | 11 to 14 V |
| G145-6 (AIRV) - C98-5 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Air Injection Control Driver) |
Disconnect the air injection control driver connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C86-5 (+B) - Body ground | Ignition Switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G145-19 (AIRP) or C86-4 (SIP) - Body ground | Always | 10 kΩ or higher |
| G145-6 (AIRV) or C86-3 (SIV) - Body ground | Always | 10 kΩ or higher |
Reconnect the air injection control driver connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Air Injection Control Driver) |
Disconnect the air injection control driver connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C86-2 (DI) - C86-1 (E) | Ignition Switch ON | 11 to 14 V |
Reconnect the air injection control driver connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C86-1 (E) - Body ground | Always | Below 1 Ω |
| C86-4 (SIP) - G145-19 (AIRP) | Always | Below 1 Ω |
| C86-3 (SIV) - G145-6 (AIRV) | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C86-2 (DI) - C86-1 (E) | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
Reconnect the ECM connector.
Reconnect the air injection control driver connector.
A
B
Disconnect the ECM connector.
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C86-2 (DI) - G146-30 (AIDI) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C86-2 (DI) or G146-30 (AIDI) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM and air injection control driver connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air injection control driver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C86-1 (E) - Body ground | Always | Below 1 Ω |
Reconnect the air injection control driver connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air injection control driver connector.
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Air Injection Control Driver) |
Connect terminals DI and SIV of the wire harness connector for the air injection control driver.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.
When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
| Tester Display |
|---|
| Secondary Air Injection Check |
Start the engine.
Perform the AIR system intrusive operation while the engine is idling.
Measure the voltage between the SIV and E terminals of the ECM connector when the AIR system is on and off.
Turn the ignition switch off.
Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C86-3 (SIV) - C86-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| C86-3 (SIV) - C86-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| *1 | Air Injection Control Driver |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Air Injection Control Driver) |
Connect terminals DI and SIP of the wire harness connector for the air injection control driver.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.
When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
| Tester Display |
|---|
| Secondary Air Injection Check |
Start the engine.
Perform the AIR system intrusive operation while the engine is idling.
Measure the voltage between the SIP and E terminals of the ECM connector when the AIR system is on and off.
Turn the ignition switch off.
Do not perform the System Check operation repetitively. It may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C86-4 (SIP) - C86-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| C86-4 (SIP) - C86-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
Reconnect the air injection control driver connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air injection control driver.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine and warm it up.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear DTCs (if stored).
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
| Tester Display |
|---|
| Secondary Air Injection Check |
Start the engine after the intelligent tester initialization is finished.
Perform the system check operation by pressing Next.
After operating the AIR system, press the Exit button to confirm the AIR system pending codes.
Check Pending DTCs.
No pending DTC output.
Turn the ignition switch off.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
Turn the ignition switch off when the Secondary Air Injection Check operation finishes.
| Proceed to |
|---|
| OK |
| NG |
OK
NG