Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P1001  Fuel Sub Tank Solenoid Duty Control Circuit  


DESCRIPTION

A Flexible Fuel Vehicle (FFV) is a vehicle with an engine that can be used with a high concentration of ethyl alcohol fuel.

This FFV uses a sub tank system, which allows fuel (with a gasoline concentration of 78% or more) to be injected to the fuel delivery spacer from the sub tank when the ambient temperature is low to enhance low-temperature startability.

The fuel volume is controlled by the ECM and varies depending on the duty ratio of the fuel injection volume control solenoid valve assembly.

If the fuel injection volume control solenoid valve assembly is stuck open, the fuel cut solenoid valve assembly will operate and cut the fuel flow based on signals from the ECM, preventing the fuel from being drawn out of the sub tank due to vacuum from the engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1001 Fuel Sub Tank Solenoid Duty Control Circuit

Both conditions are met (1 trip detection logic):

1.

Target duty ratio of fuel injection volume control solenoid valve is between 5 and 90%.

2.

Difference between target control value and actual control value continues for 2 seconds or more.



·

Open or short in solenoid valve assembly (for fuel injection volume control) circuit

·

Solenoid valve assembly (for fuel injection volume control)

·

FFV relay

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A242464
3.115,1.146 3.208,1.292 0.094,0.146 10 false 3 2.167,1.146 2.26,1.292 0.094,0.146 10 false 5 3.083,0.49 3.177,0.635 0.094,0.146 10 false 1 0.552,5.875 1.406,6.083 0.854,0.208 10 false BATT P/I 0.677,6.896 1.302,7.198 0.625,0.302 10 false Battery 2.188,0.51 2.281,0.656 0.094,0.146 10 false 2 4,1.146 4.094,1.292 0.094,0.146 10 false 2 5.24,1.146 5.333,1.292 0.094,0.146 10 false 1 4,2.427 4.146,2.698 0.146,0.271 10 false 2 5.24,2.427 5.396,2.646 0.156,0.219 10 false 1 2.302,1.583 3.198,1.781 0.896,0.198 10 false F-PMP/FFV 2.771,2.385 2.865,2.531 0.094,0.146 10 false 2 4.031,5.563 4.5,5.75 0.469,0.188 10 false MAIN 2.094,2.833 3.083,3.25 0.99,0.417 10 false Fuel Pump (for Fuel Sub Tank) 3.854,1.615 5.448,2.021 1.594,0.406 10 false Solenoid Valve Assembly (for Fuel Cut Control) 3.677,2.865 5.583,3.271 1.906,0.406 10 false Solenoid Valve Assembly (for Fuel Injection Volume Control) 3.854,1.458 4.188,1.677 0.333,0.219 10 false A69 3.677,2.719 4.083,2.969 0.406,0.25 10 false A70 2.104,2.688 2.427,2.885 0.323,0.198 10 false A71 5.646,1.229 6.073,1.479 0.427,0.25 10 false G145 6.083,1.229 6.542,1.469 0.458,0.24 10 false SSV 5.75,1.01 5.948,1.219 0.198,0.208 10 false 1 5.635,0.604 6.083,0.813 0.448,0.208 10 false G146 6.083,0.594 6.531,0.833 0.448,0.24 10 false FFR 5.719,0.385 5.948,0.594 0.229,0.208 10 false 11 5.677,6.469 6.052,6.698 0.375,0.229 10 false C98 6.083,6.469 6.448,6.688 0.365,0.219 10 false E01 5.708,6.229 5.948,6.427 0.24,0.198 10 false 11 5.635,5.219 6.083,5.427 0.448,0.208 10 false G146 6.083,5.219 6.573,5.469 0.49,0.25 10 false MREL 5.719,4.99 5.958,5.208 0.24,0.219 10 false 12 4.938,4.99 5.229,5.208 0.292,0.219 10 false 2 5.635,2.542 6.042,2.802 0.406,0.26 10 false G145 6.073,2.531 6.552,2.771 0.479,0.24 10 false DSSV 5.719,2.313 5.948,2.542 0.229,0.229 10 false 18 6.281,7.104 6.708,7.354 0.427,0.25 10 false ECM 2.313,2.385 2.406,2.531 0.094,0.146 10 false 1 0.198,0.531 1.156,0.969 0.958,0.438 10 false from Ignition Switch 3.094,4.813 3.469,5.094 0.375,0.281 10 false EFI 1.656,0.771 2.167,1.042 0.51,0.271 10 false IGN 4.188,1.125 4.656,1.333 0.469,0.208 10 false SFC+ 4.771,1.125 5.188,1.365 0.417,0.24 10 false SFC- 4.188,2.438 4.635,2.625 0.448,0.188 10 false FFV+ 4.771,2.438 5.208,2.604 0.438,0.167 10 false FFV- 2.26,4.094 2.531,4.302 0.271,0.208 10 false 1J 2.24,4.656 2.563,4.958 0.323,0.302 10 false 1H 3.177,5.719 3.448,5.885 0.271,0.167 10 false 1J 4.896,5.219 5.24,5.51 0.344,0.292 10 false 1J 3.125,5.5 3.302,5.677 0.177,0.177 10 false 3 2.292,4.427 2.49,4.635 0.198,0.208 10 false 1 2.292,3.865 2.542,4.104 0.25,0.24 10 false 5 4.021,5.948 5.25,6.333 1.229,0.385 10 false Integration Relay

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FFV RELAY
a.
A234567
2.354,1.552 2.354,1.313 false 2.771,1.563 2.615,1.219 false 2.344,0.677 2.344,0.917 false 2.781,0.667 2.875,1.01 false 2.313,0.5 2.469,0.698 0.156,0.198 10 false 2 2.75,0.49 2.906,0.688 0.156,0.198 10 false 3 2.313,1.573 2.469,1.771 0.156,0.198 10 false 1 2.76,1.573 2.917,1.771 0.156,0.198 10 false 5

Remove the FFV relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω



c.

Reinstall the FFV relay.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (FFV RELAY - SOLENOID VALVE ASSEMBLY)

NG

REPLACE FFV RELAY

2.CHECK HARNESS AND CONNECTOR (FFV RELAY - SOLENOID VALVE ASSEMBLY)
a.

Remove the FFV relay from the engine room relay block.


b.

Disconnect the solenoid valve assembly (for fuel injection volume control) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
FFV relay terminal (3) - A70-2 (FFV+) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
FFV relay terminal (3) or A70-2 (FFV+) - Body ground Always 10 kΩ or higher



d.

Reinstall the FFV relay.


e.

Reconnect the solenoid valve assembly (for fuel injection volume control) connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT SOLENOID VALVE ASSEMBLY (FOR FUEL INJECTION VOLUME CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FFV RELAY - SOLENOID VALVE ASSEMBLY)

3.INSPECT SOLENOID VALVE ASSEMBLY (FOR FUEL INJECTION VOLUME CONTROL)
a.

Inspect the solenoid valve assembly (for fuel injection volume control).

Click hereEngine / Hybrid System>2TR-FBE FUEL>SOLENOID VALVE(for Fuel Injection Volume Control)>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SOLENOID VALVE ASSEMBLY (FOR INJECTION VOLUME CONTROL) - ECM)

NG

REPLACE SOLENOID VALVE ASSEMBLY (FOR FUEL INJECTION VOLUME CONTROL)

4.CHECK HARNESS AND CONNECTOR (SOLENOID VALVE ASSEMBLY (FOR INJECTION VOLUME CONTROL) - ECM)
a.

Disconnect the solenoid valve assembly (for injection volume control) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A70-1 (FFV-) - G145-18 (DSSV) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A70-1 (FFV-) or G145-18 (DSSV) - Body ground Always 10 kΩ or higher



d.

Reconnect the solenoid valve assembly (for injection volume control) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CHECK SUB TANK FUEL PUMP CONTROL CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SOLENOID VALVE ASSEMBLY (FOR INJECTION VOLUME CONTROL) - ECM)

5.CHECK SUB TANK FUEL PUMP CONTROL CIRCUIT
a.

Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE SUB TANK FUEL PUMP CONTROL CIRCUIT