Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › TIMING BELT(w/o DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052166 TIMING BELT(w/o DPF) A

2KD-FTV ENGINE MECHANICAL  TIMING BELT(w/o DPF)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

a.

Using a 10 mm hexagon wrench, install a new washer and the No. 1 timing belt idler with the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


b.

Check that the idler pulley moves smoothly.

If the idler pulley does not move smoothly, check the installation condition of the idler and washer.


Hide 2.INSTALL TIMING BELT

a.
A070691
0.781,1.083 0.208,1.083 true 0.781,1.385 0.552,1.385 0.552,1.385 0.552,1.094 true 2.948,1.115 2.948,0.927 2.948,0.927 3.094,0.927 true 3.031,1.104 3.031,0.927 true 0.021,0.99 0.188,1.167 0.167,0.177 10 false *1 3.115,0.844 3.281,1.021 0.167,0.177 10 false *1
*1 Timing Mark


Check that the timing marks are aligned as shown in the illustration.

NOTICE:
·

Make sure that the engine is cold.

·

When turning the crankshaft, the valve heads will hit against the piston. Do not turn the crankshaft more than necessary.



HINT:

If reusing the timing belt, align the points marked during removal, and install the belt with the arrow pointing in the direction of crankshaft revolution.



b.

Install the timing belt to the pump drive shaft pulley, camshaft timing pulley and No. 1 timing belt idler in sequence.


c.
A070548

Place the tensioner upright. Then set a press on the top of the tensioner.

NOTICE:
·

Do not scratch or deform the rod end.

·

Press in the tensioner rod.

·

Protect the tip of the push rod with a cloth in order to prevent damage.




d.

Using the press, slowly push in the push rod using 981 to 9800 N (100 to 999 kgf, 220 to 2203 lbf) of force.

NOTICE:

Do not apply a load of over 9800 N (999 kgf, 2203 lbf) to the push rod.



e.

Align the holes of the push rod and housing. Then pass a 1.5 mm hexagon wrench through the holes to fix the push rod in place.


f.

Temporarily install the timing belt tensioner with the 2 bolts while pushing the idler pulley toward the timing belt.


g.

Tighten the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

NOTICE:

Uniformly tighten the 2 bolts.



h.
A059983

Remove the 1.5 mm hexagon wrench from the tensioner.


i.
A301857
0.479,1.167 0.844,1.167 true 0.833,1.448 0.688,1.448 0.688,1.448 0.688,1.167 true 3.01,1.188 3.01,0.99 3.01,0.99 3.219,0.99 true 3.094,1.208 3.094,1 true 0.302,1.104 0.49,1.292 0.188,0.188 10 true *1 3.208,0.896 3.427,1.094 0.219,0.198 10 true *1
*1 Timing Mark


Turn the crankshaft clockwise 720° and check that the timing marks are aligned as shown in the illustration.


Hide 3.INSTALL NO. 1 TIMING BELT COVER

a.

Install the timing belt cover and 6 washers with the 6 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 5.INSTALL RADIATOR HOSE INLET

Hide 8.INSTALL NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)