Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CAMSHAFT(w/ DPF) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052177 CAMSHAFT(w/ DPF) A

2KD-FTV ENGINE MECHANICAL  CAMSHAFT(w/ DPF)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL CAMSHAFT

a.
G036616
0.573,1.635 1.177,1.792 1.177,1.792 1.25,1.792 true 0.125,1.156 0.458,1.344 0.333,0.188 10 false 90° 1.271,1.708 1.448,1.865 0.177,0.156 10 false *1
*1 Key


Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

HINT:

Set the No. 1 cylinder to 90° BTDC/compression to prevent the top of the piston from hitting against the valve head.



b.
A060149
0.365,0.542 1.021,0.344 1.021,0.344 1.125,0.344 true 0.344,0.021 0.531,0.188 0.188,0.167 10 false *a 1.146,0.26 1.323,0.417 0.177,0.156 10 false *1
*1 Key Groove
*a Upward


Install the camshafts.

i.

Apply engine oil to the thrust portion of the camshaft.


ii.

Place the camshaft on the cylinder head with the key groove facing upward.


iii.
A060150

Align the timing marks (1-dot marks) of the camshaft drive and driven main gears and set the No. 2 camshaft in place.



c.

Remove any old seal packing (FIPG material) from the camshaft bearing cap.


d.
A060283
0.906,1.417 0.906,1.74 true 1.635,0.844 1.281,0.438 1.281,0.438 1.198,0.438 false 2.792,0.813 2.542,0.531 2.542,0.531 2.365,0.531 true 0.813,1.76 1,1.927 0.188,0.167 10 false *2 2.375,0.25 3.417,0.427 1.042,0.177 10 false 8 mm (0.315 in.) 0.99,0.323 1.177,0.49 0.188,0.167 10 false *1 2.167,0.448 2.354,0.615 0.188,0.167 10 false *1
*1 Seal Packing
*2 Oil Passage


Apply seal packing to the specified areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:
·

Do not allow seal packing to contact the oil passage of the bearing cap.

·

After applying seal packing, install the camshaft bearing caps within 3 minutes and tighten the bolts within 15 minutes.

·

Do not start the engine for at least 2 hours after installation.




e.
A060146

Install the 5 bearing caps to their proper locations.


f.
A060147
1.729,1.031 1.885,1.198 0.156,0.167 10 true 9 1.885,0.542 2.042,0.708 0.156,0.167 10 true 1 1.698,0.354 1.854,0.521 0.156,0.167 10 false 2 2.135,0.729 2.292,0.896 0.156,0.167 10 true 3 2.24,0.385 2.396,0.552 0.156,0.167 10 true 4 1.292,0.667 1.448,0.833 0.156,0.167 10 false 8 1.469,0.813 1.625,0.979 0.156,0.167 10 true 7 2.5,0.5 2.656,0.667 0.156,0.167 10 true 6 2.125,0.156 2.281,0.323 0.156,0.167 10 false 5 2.781,0.177 3.01,0.344 0.229,0.167 10 false 10 2.563,0.052 2.792,0.219 0.229,0.167 10 false 11 3.042,0.375 3.271,0.542 0.229,0.167 10 false 12 0.875,1.135 1.104,1.302 0.229,0.167 10 true 13 0.615,0.958 0.844,1.125 0.229,0.167 10 false 14 1.073,1.354 1.302,1.521 0.229,0.167 10 true 15

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


g.

Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


h.
A060145
1.854,0.771 1.063,0.771 true 0.719,0.688 1.052,0.854 0.333,0.167 10 false SST

Install a new camshaft oil seal.

i.

Apply MP grease to the lip of a new oil seal.


ii.

Using SST and a hammer, tap in the oil seal until its surface is flush with the surfaces of the camshaft bearing cap and cylinder head.

SST
09608-06041  



Hide 11.INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 16.INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 17.TEMPORARILY INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER

Hide 18.TIGHTEN ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER

Hide 26.INSTALL NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 29.INSTALL MANIFOLD STAY WITH VACUUM SWITCHING VALVE

Hide 34.INSTALL FRONT WHEEL LH

Hide 40.INSTALL RADIATOR HOSE INLET