Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE UNIT(w/ DPF) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052180 ENGINE UNIT(w/ DPF) A

2KD-FTV ENGINE MECHANICAL  ENGINE UNIT(w/ DPF)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A253830
1.646,1.167 0.875,1.167 true 1.323,1.594 1.177,1.594 1.177,1.594 1.177,1.177 true 0.521,1.083 0.823,1.25 0.302,0.167 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the rear engine oil seal retainer edge.

SST
09518-36030  
09950-70010  (09951-07100)

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the oil seal at an angle.




b.

Apply MP grease to the lip of the oil seal.


Hide 2.INSTALL SUPPLY PUMP OIL SEAL

a.
A058118
1.823,1.333 2.406,1.333 2.406,1.333 1.698,1.021 true 1.885,1.5 2.406,1.333 true 2.458,1.26 2.813,1.427 0.354,0.167 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

SST
09223-15020  
09502-12010  
09950-70010  (09951-07100)

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the oil seal at an angle.




b.

Apply MP grease to the lip of the oil seal.


Hide 3.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A058119
1.792,1.24 2.385,1.344 true 2.438,1.26 2.771,1.427 0.333,0.167 10 false SST

Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing gear cover edge.

SST
09214-76011  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the oil seal at an angle.




b.

Apply MP grease to the lip of the oil seal.


Hide 4.INSTALL REAR ENGINE OIL SEAL RETAINER

a.

Remove any old seal packing (FIPG material) from the oil pan and cylinder block.


b.
A246541
2.317,0.63 2.665,0.297 2.665,0.297 2.754,0.297 false 2.764,0.209 2.948,0.375 0.185,0.167 10 *1
*1 Seal Packing


Apply seal packing to the places shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:

After applying seal packing, install the rear engine oil seal retainer within 3 minutes and tighten the bolts within 15 minutes.



c.

Install the rear engine oil seal retainer with the 5 bolts. Alternately tighten the 5 bolts in several passes.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 5.INSTALL TIMING GEAR CASE ASSEMBLY

a.
A060152
1.646,0.688 0.552,0.688 true 1.813,1.708 0.771,1.708 true 0.375,0.594 0.531,0.74 0.156,0.146 10 false *1 0.594,1.615 0.75,1.76 0.156,0.146 10 false *1
*1 New O-Ring


Install 2 new O-rings to the cylinder block.


b.
A239302
2.323,0.781 2.74,0.26 2.74,0.26 2.833,0.26 true 2.854,0.177 3.01,0.333 0.156,0.156 10 false *1
*1 New Gasket


Install a new gasket to the groove of the timing gear case.


c.

Remove any old seal packing (FIPG material).


d.
A100875
0.51,1.646 1.208,1.646 true 0.302,1.552 0.563,1.75 0.26,0.198 10 false *1
*1 Seal Packing


Apply seal packing to the timing gear case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:

After applying seal packing, install the timing gear case assembly within 3 minutes and tighten the bolts within 15 minutes.



e.
A303437
1.615,1.406 1.771,1.604 0.156,0.198 10 false A

Install the timing gear case with the union bolt and 8 bolts.

Torque:
for union bolt (A) : 16 N*m (163 kgf*cm, 12 ft.*lbf)
for bolt : 13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer with the 2 bolts and 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 7.INSTALL OIL PAN SUB-ASSEMBLY

a.
A151187
1.452,1.292 1.594,1.464 0.142,0.171 10 A 1.452,1.753 1.594,1.924 0.142,0.171 10 A 2.547,1.292 2.69,1.464 0.142,0.171 10 B 2.547,1.753 2.69,1.924 0.142,0.171 10 B 0.962,2.532 1.314,2.692 0.353,0.16 10 A - A 2.425,2.532 2.778,2.692 0.353,0.16 10 B - B

Remove any old seal packing (FIPG material).


b.

Apply seal packing to the oil pan as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal packing diameter:

4 mm (0.157 in.)


NOTICE:

After applying seal packing, install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes.



c.

Install the oil pan with the 22 bolts and 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 8.INSTALL ENGINE OIL LEVEL SENSOR

a.

Install the engine oil level sensor with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 9.INSTALL INJECTION GEAR

a.

Install a new O-ring and the fuel supply pump with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Temporarily install the injection gear with the nut.

HINT:

Fit the key (protrusion) of the fuel supply pump into the key slot of the injection gear.



c.
A222336
1.26,1.708 0.896,2 0.896,2 0.792,2 true 0.625,1.917 0.781,2.073 0.156,0.156 10 false *1
*1 New O-Ring


Install a new O-ring to the injection gear.


d.
A069845
2.917,1 2.854,1.313 false 2.677,1.344 3.031,1.521 0.354,0.177 10 false SST

Install the injection gear set nut.


e.

Using SST, tighten the set nut.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
64 N*m (650 kgf*cm, 47 ft.*lbf)


Hide 10.INSTALL CRANKSHAFT TIMING GEAR

A061827
2.25,1.063 2.979,1.708 true 2.833,1.74 3.156,1.927 0.323,0.188 10 false SST

a.

Position the crankshaft timing gear with the "1" timing marks facing forward.


b.

Align the key groove of the crankshaft timing gear with the set key on the crankshaft.


c.

Using SST and a hammer, tap on the timing gear to install it.

SST
09223-00010  


Hide 11.INSTALL NO. 1 IDLE GEAR SHAFT

a.
A069846
2.302,1.219 2.052,1.708 2.052,1.708 1.958,1.708 true 1.729,1.625 1.927,1.802 0.198,0.177 10 false *1
*1 Engine Oil


Apply a coat of engine oil to the No. 1 idle gear shaft.


b.
A060159
1.573,1.063 1.208,0.521 1.208,0.521 1.073,0.521 true 0.854,0.417 1.031,0.583 0.177,0.167 10 true *1
*1 Oil Hole


Install the gear shaft as shown in the illustration.


Hide 12.INSTALL NO. 2 IDLE SUB GEAR

a.
A060166

Using a cloth or equivalent, mount the No. 1 idle gear in a vise as shown in the illustration.

NOTICE:

Be careful not to damage the gear.



b.
A303438
2.229,1.427 2.49,1.188 2.49,1.188 2.688,1.188 false 0.76,1.458 0.917,1.458 0.917,1.458 1.417,1.74 true 0.813,2.688 0.948,2.688 0.948,2.688 1.51,3.604 true 2.208,2.542 2.552,2.542 false 2.135,0.74 2.396,0.5 2.396,0.5 2.594,0.5 false 2.677,0.406 2.99,0.604 0.313,0.198 10 false *1 2.729,1.052 3.042,1.25 0.313,0.198 10 false *2 2.635,2.448 2.948,2.646 0.313,0.198 10 false *3 0.552,1.344 0.865,1.542 0.313,0.198 10 false *4 0.635,2.594 0.948,2.792 0.313,0.198 10 false *4
*1 Wave Washer
*2 No. 2 Idle Sub Gear
*3 Gear Spring
*4 Pin


Install the gear spring.


c.

Install the No. 2 idle sub gear.

HINT:

Align the pins on the gears with the spring ends.



d.

Install the wave washer.


e.

Using snap ring pliers, install the snap ring.


f.
A060164
2.292,0.469 2.51,0.198 2.51,0.198 2.573,0.198 false 0.958,1.906 0.594,1.698 0.594,1.698 0.49,1.698 false 2.094,1.76 1.563,1.958 1.563,1.958 1.479,1.958 true 2.021,1.604 2.677,1.438 2.677,1.438 2.781,1.438 true 2.604,0.104 2.938,0.25 0.333,0.146 10 false SST 1.281,1.865 1.458,2.021 0.177,0.156 10 false *2 2.813,1.365 2.969,1.521 0.156,0.156 10 false *3 0.302,1.594 0.469,1.75 0.167,0.156 10 false *1
*1 Service Bolt
*2 No. 1 Idle Gear
*3 No. 2 Idle Sub Gear
V100135

Turn


Using SST, align the holes of the No. 1 idle gear and No. 2 idle sub gear by turning the No. 2 idle sub gear clockwise, and temporarily install a service bolt.

SST
09960-10010  (09962-01000, 09963-00700)


g.

Align the gear teeth of the No. 1 idle gear and No. 2 idle sub gear and tighten the service bolt.


Hide 13.INSTALL NO. 1 IDLE GEAR

a.
G036757
1.948,0.583 2.583,0.281 2.583,0.281 2.698,0.281 true 2.063,0.073 2.271,0.24 0.208,0.167 10 true *a 2.76,0.198 3.125,0.365 0.365,0.167 10 false SST
*a Turn


Align the "4" and "5" timing marks of the idle gear and crankshaft timing gear.


b.

Using SST, turn the injection gear and align the "4" timing marks of the idle gear and injection gear, and then mesh the gears.

SST
09960-10010  (09962-01000, 09963-00700)


c.
A222334
2.438,1.667 1.406,1.844 1.406,1.844 1.156,1.844 true 0.958,1.75 1.135,1.917 0.177,0.167 10 false *1
*1 Service Bolt


Position the idle gear thrust plate with the protrusion facing forward.


d.

Align the bolt holes and install the idle gear thrust plate with the 2 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


e.

Remove the service bolt.


Hide 14.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

HINT:

When replacing the No. 1 crankshaft position sensor plate, perform "Crank Time Compensation Reset" (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).


a.

Align the key groove of the No. 1 crankshaft position sensor plate with the set key.


b.

Install the No. 1 crankshaft position sensor plate with the cupped side facing outward.


Hide 15.INSTALL TIMING GEAR COVER

a.

Remove any old seal packing (FIPG material).


b.
A225340
1.677,0.76 1.927,0.396 1.927,0.396 2,0.396 true 2.052,0.323 2.323,0.5 0.271,0.177 10 false *1
*1 Seal Packing


Apply seal packing to the timing gear cover as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:

After applying seal packing, install the timing gear cover within 3 minutes and tighten the bolts within 15 minutes.



c.

Install a new O-ring to the timing gear case.


d.

Install the timing gear cover with the 14 bolts and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


e.
A248630

Remove the screw plug and gasket.


f.

Pour approximately 50 cc (3.05 cu. in.) of engine oil into the oil pump.


g.

Install a new gasket and the screw plug.

Torque:
42 N*m (423 kgf*cm, 31 ft.*lbf)


h.

Install the vacuum transmitting pipe with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 16.INSTALL ENGINE WATER PUMP ASSEMBLY

a.

Install a new gasket and the engine water pump with the 5 bolts and 2 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 19.INSTALL VALVE LIFTER

a.

Install the valve lifters.


b.

Check that each valve lifter rotates smoothly by hand.


Hide 28.INSTALL OIL FILLER CAP SUB-ASSEMBLY