Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009575 2TR-FE ENGINE MECHANICAL _0052188 REAR CRANKSHAFT OIL SEAL A

2TR-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 1.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A252565
2.438,0.646 2.813,1.896 true 2.979,1.917 2.813,1.917 2.813,1.917 2.083,1.479 true 3.031,1.813 3.365,1.969 0.333,0.156 10 false SST

Apply a light coat of MP grease to the lip of a new oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the oil seal.

·

Do not allow MP grease to contact the dust seal.




b.

Using SST and a hammer, tap in the oil seal until its surface is flush with the oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07150)

NOTICE:
·

Wipe off any extra grease from the crankshaft.

·

Do not tap in the oil seal at an angle.




Hide 2.INSTALL FLYWHEEL SUB-ASSEMBLY

a.
A099210
0.885,1.427 0.667,1.583 0.667,1.583 1.219,1.708 false 0.271,1.51 0.75,1.708 0.479,0.198 10 false SST

Using SST, hold the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.

Clean the bolts and bolt holes.


c.

Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A252562
2.156,0.958 2.354,1.115 0.198,0.156 10 true 10 1.167,1.51 1.292,1.667 0.125,0.156 10 true 3 1.781,0.458 1.906,0.615 0.125,0.156 10 true 7 2.135,1.24 2.26,1.396 0.125,0.156 10 true 6 1.073,0.823 1.198,0.979 0.125,0.156 10 true 5 2.073,0.646 2.198,0.802 0.125,0.156 10 true 4 1.313,0.51 1.438,0.667 0.125,0.156 10 true 2 1.896,1.563 2.021,1.719 0.125,0.156 10 true 1 1.021,1.177 1.146,1.333 0.125,0.156 10 true 9 1.521,1.667 1.646,1.823 0.125,0.156 10 true 8

Install the flywheel with the 10 bolts and uniformly tighten the bolts in several steps in the sequence shown in the illustration.

Torque:
27 N*m (270 kgf*cm, 20 ft.*lbf)


e.

Mark the top of the bolts with paint.


f.

Tighten the 10 bolts 90° in the same sequence.


g.

Check that the paint marks are now at a 90° angle to the top.


Hide 3.INSTALL CLUTCH DISC ASSEMBLY

Hide 4.INSTALL CLUTCH COVER ASSEMBLY

Hide 5.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY