Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CYLINDER HEAD › from 2012.04
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052212 CYLINDER HEAD G

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.CLEAN CYLINDER HEAD SUB-ASSEMBLY

a.

Using a gasket scraper, remove all the gasket material from the surface which contacts the cylinder block.

NOTICE:

Be careful not to scratch the surface which contacts the cylinder block.



b.

Using a wire brush, remove all the carbon from the combustion chambers.

NOTICE:

Be careful not to scratch the cylinder block contact surface.



c.
A075607

Using a valve guide bushing brush and solvent, clean all the guide bushes.


d.

Using a soft brush and solvent, thoroughly clean the cylinder head.


Hide 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the surfaces that contact the cylinder block and manifolds for warpage.

A302389
2.198,0.208 2.51,0.406 0.313,0.198 10 false *a 3.792,0.219 4.104,0.417 0.313,0.198 10 false *b 5.406,0.229 5.719,0.427 0.313,0.198 10 false *c
*a Cylinder Block Side *b Intake Manifold Side
*c Exhaust Manifold Side - -


Maximum warpage:

0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the cylinder head sub-assembly.


Hide 3.INSPECT CYLINDER HEAD FOR CRACKS

a.

Using a dye penetrant, check the intake ports, exhaust ports and cylinder head surface for cracks.

If cracked, replace the cylinder head sub-assembly.


Hide 4.CLEAN VALVE SEAT

a.
A075612
0.896,0.323 1.104,0.323 1.104,0.323 1.604,0.813 true 0.667,0.24 0.854,0.427 0.188,0.188 10 false *1
*1 45° Carbide Cutter


Using a 45° carbide cutter, resurface the valve seats.

HINT:

Only remove the amount of metal necessary to clean the seats.



Hide 5.CLEAN VALVE

a.

Clean the valves.

i.

Using a gasket scraper, chip off any carbon from the valve head.


ii.

Using a wire brush, thoroughly clean the valve.



Hide 6.INSPECT VALVE

a.

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:
Item Specified Condition
Intake 5.470 to 5.485 mm (0.2154 to 0.2159 in.)
Exhaust 5.465 to 5.480 mm (0.2152 to 0.2158 in.)


If the valve stem diameter is not as specified, check the oil clearance.


b.
A302397
3.021,1.813 3.333,2.01 0.313,0.198 10 false *1
*1 Valve Face Angle


Check the valve face angle.

i.

Grind the valve sufficiently to remove pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

44.5°




c.
A302398
0.552,1.927 0.865,2.125 0.313,0.198 10 false *1
*1 Margin Thickness


Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the valve.


d.

Using a vernier caliper, measure the overall valve length.

Standard Overall Length:
Item Specified Condition
Intake 106.95 mm (4.21 in.)
Exhaust 105.80 mm (4.17 in.)


Minimum Overall Length:
Item Specified Condition
Intake 106.40 mm (4.19 in.)
Exhaust 105.30 mm (4.15 in.)


If the overall length is less than the minimum, replace the valve.


e.
EM00255

Check the surface of the valve stem tip for wear.

NOTICE:

Do not grind off more than the minimum length.


If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.


Hide 7.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A075615

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Bush inside diameter:

5.510 to 5.530 mm (0.217 to 0.218 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.030 to 0.065 mm (0.00118 to 0.00256 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.08 mm (0.00315 in.)
Exhaust 0.10 mm (0.00394 in.)


If the clearance is more than the maximum, replace the valve and valve guide bush.


Hide 8.INSPECT VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

NOTICE:

Do not rotate the valve.



c.
A302399
1.51,1.229 1.823,1.427 0.313,0.198 10 false *1
*1 Width


Check the valve face and valve seat using the following procedure.

i.

Check that Prussian blue appears 360° around the valve face.

If not, replace the valve.


ii.

If Prussian blue appears 360° around the valve seat, the guide and valve face are concentric.

If not, resurface the valve seat.


iii.

Check that the valve seat contact is in the middle of the valve face with the valve seat width between 1.0 and 1.4 mm (0.0394 to 0.0551 in.).



Hide 9.INSPECT INNER COMPRESSION SPRING

a.
EM00801

Using a vernier caliper, measure the free length of the inner compression spring.

Standard free length:

47.80 mm (1.88 in.)


If the free length is not as specified, replace the inner compression spring.


b.
A302400
1.146,0.104 1.458,0.302 0.313,0.198 10 false *1
*1 Deviation


Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

2.0 mm (0.0787 in.)


If the deviation is more than the maximum, replace the inner compression spring.


c.
EM00281

Using a spring tester, measure the tension of the valve spring when it is compressed to the specified installation length.

Standard installed tension:

186 to 206 N (19 to 21 kgf, 42 to 46 lbf) at 33.3 mm (1.31 in.)


If the installed tension is not as specified, replace the inner valve spring.


Hide 10.INSPECT CAMSHAFT THRUST CLEARANCE


b.

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.04 to 0.09 mm (0.0157 to 0.0354 in.)


Maximum thrust clearance:

0.11 mm (0.00433 in.)


If the thrust clearance is more than the maximum, replace the camshafts.

If necessary, replace the camshaft bearing caps and cylinder head as a set.


Hide 11.INSPECT VALVE LIFTER

a.
P016860

Using a micrometer, measure the lifter diameter.

Standard lifter diameter:

30.966 to 30.976 mm (1.219 to 1.220 in.)


If the diameter is not as specified, replace the valve lifter.


b.
A075621

Using a caliper gauge, measure the valve lifter bore diameter of the cylinder head.

Standard lifter bore diameter:

31.009 to 31.025 mm (1.2208 to 1.2215 in.)


If the diameter is not as specified, replace the cylinder head.


c.

Subtract the valve lifter diameter measurement from the valve lifter bore diameter measurement.

Standard oil clearance:

0.033 to 0.059 mm (0.00130 to 0.00232 in.)


Maximum oil clearance:

0.08 mm (0.00315 in.)


If the oil clearance is more than the maximum, replace the valve lifter. If necessary, replace the cylinder head.