Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CYLINDER BLOCK › from 2012.04
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052213 CYLINDER BLOCK A

1GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Install new stud bolts.

Torque:
for stud bolt A and B : 11 N*m (112 kgf*cm, 8 ft.*lbf)
for stud bolt C : 4.0 N*m (41 kgf*cm, 35 in.*lbf)

A302413
6.635,2.177 6.823,1.292 6.823,1.292 6.542,1.292 false 0.667,0.198 0.979,0.354 0.313,0.156 10 false *a 4.333,0.188 4.646,0.344 0.313,0.156 10 false *b 0.719,2.646 1.031,2.802 0.313,0.156 10 false *c 3.333,1.26 4.406,1.458 1.073,0.198 10 false 52 mm (2.05 in.) 3,1.958 3.333,2.177 0.333,0.219 10 false (M8) 3.01,4.448 3.344,4.667 0.333,0.219 10 false (M7) 3.396,3.646 4.521,3.854 1.125,0.208 10 false 56 mm (2.21 in.) 6.302,1.698 6.635,1.917 0.333,0.219 10 false (M6) 5.979,2.229 7.146,2.427 1.167,0.198 10 false 23 mm (0.906 in.) 0.667,1.781 0.823,1.979 0.156,0.198 10 false A 2.552,1.698 2.708,1.896 0.156,0.198 10 false A 0.479,4.094 0.635,4.292 0.156,0.198 10 false B 4.365,1.125 4.521,1.323 0.156,0.198 10 false C 6.208,0.833 6.365,1.031 0.156,0.198 10 false C
*a Front Side *b Upper Side
*c Lower Side - -



Hide 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.

Using a 5 mm hexagon socket wrench, install the 3 No. 1 oil nozzles with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 3.INSTALL WITH PIN PISTON SUB-ASSEMBLY

a.
A302554

Using a screwdriver, install a new snap ring on one side of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



b.

Gradually heat the piston to approximately 80°C (176°F).


c.
A075846
1.583,0.229 1.969,0.229 1.969,0.229 2.229,0.479 true 1.396,0.146 1.573,0.323 0.177,0.177 10 false *1 1.052,1.885 1.25,2.052 0.198,0.167 10 false *1
*1 Front Mark


Coat the piston pin with engine oil.


d.

Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.

HINT:

The piston and pin are a matched set.



e.

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


f.
A302554

Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



Hide 4.INSTALL PISTON RING SET

a.

Install the oil ring (expander) and 2 side rails by hand.


b.
A302414
0.813,1.396 0.813,1.177 false 0.76,1.448 1.073,1.646 0.313,0.198 10 false *1 0.844,2.854 1.156,3.052 0.313,0.198 10 false *2 2.313,2.865 2.625,3.063 0.313,0.198 10 false *3
*1 Painted Mark
*2 No. 1 Compression Ring
*3 No. 2 Compression Ring
V100135

Right Side


Using a piston ring expander, install the 2 compression rings with the painted mark on the right side.


c.
A302415
0.635,1.969 0.927,2.125 0.292,0.156 10 false *1 1.99,1.927 2.281,2.083 0.292,0.156 10 false *4 0.271,1.438 0.563,1.594 0.292,0.156 10 false *5 0.531,0.635 0.823,0.792 0.292,0.156 10 false *6 0.479,0.167 0.771,0.323 0.292,0.156 10 false *2 1.948,0.031 2.24,0.188 0.292,0.156 10 false *3
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Lower Side Rail
*4 Upper Side Rail
*5 Expander
*6 Front Mark


Position the piston rings so that the ring ends are as shown in the illustration.


Hide 5.INSTALL CRANKSHAFT BEARING

HINT:
A223696
0.594,1.844 1.24,2.042 0.646,0.198 10 false 22.4 mm 2.417,1.844 3.063,2.042 0.646,0.198 10 false 19.0 mm 0.719,0.229 0.927,0.427 0.208,0.198 10 false *1 2.542,0.208 2.75,0.406 0.208,0.198 10 false *2
*1 No. 1 and No. 4 Journal Bearings
*2 No. 2 and No. 3 Journal Bearings


Main bearings come in widths of 19.0 mm (0.748 in.) and 22.4 mm (0.882 in.). Install the 22.4 mm (0.882 in.) bearings in the No. 1 and No. 4 cylinder block journal positions with the bearing caps. Install the 19.0 mm (0.748 in.) bearings in the No. 2 and No. 3 positions.


a.

Clean each main journal and bearing.


b.

Install the upper bearing.

i.
A183116
1.63,3.528 1.825,3.73 0.195,0.203 10 *a 2.504,3.528 2.713,3.712 0.21,0.184 10 *b
*a CORRECT
*b INCORRECT


Install the upper bearing to the cylinder block as shown in the illustration.

NOTICE:
·

Do not apply engine oil to the bearings or contact surfaces.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

·

Do not allow coolant to come into contact with the inner surface of the bearing.

·

If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.





c.
A183118
2.333,3.448 2.625,3.792 2.625,3.792 2.625,4.01 true 0.854,3.677 1.031,3.875 0.177,0.198 10 false A 1.969,3.688 2.104,3.865 0.135,0.177 10 false B 2.563,4.052 2.771,4.25 0.208,0.198 10 false *2 0.781,2.104 1,2.302 0.219,0.198 10 false *1
*1 Mark 1, 2, 3 or 4
*2 Vernier Caliper


Install the lower bearing.

i.

Install the lower bearings to the crankshaft bearing caps.


ii.

Using a vernier caliper, measure the distance between the edge of the crankshaft bearing cap and the edge of the lower bearing.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:
·

Do not apply engine oil to the bearings or contact surfaces.

·

Do not allow coolant to come into contact with the inner surface of the bearing.

·

If any coolant comes into contact with the inner surface of the bearing, replace the bearing with a new one.





Hide 6.INSTALL CRANKSHAFT

NOTICE:

Clean the contact surface of each main journal and crank pin.


a.

Apply new engine oil to the upper bearing and install the crankshaft to the cylinder block.


b.
A076393

Push the crankshaft in the rear thrust direction to create clearance, and then install a thrust washer to the No. 2 journal position with the oil groove facing the front of the engine.


c.

Push the crankshaft in the forward thrust direction to create clearance, and then install a thrust washer to the No. 2 journal position with the oil groove facing the rear of the engine.


d.
A076075

Install the 2 lower thrust washers to the No. 2 bearing cap with the grooves facing outward.


e.
A076067

Examine the front marks and numbers and set the crankshaft bearing caps on the cylinder block.


f.

Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts.


g.

Temporarily install the 8 crankshaft bearing cap bolts to the inside positions.


h.
A076069
0.833,1.615 1.021,1.802 0.188,0.188 10 false *a
*a Less than 6 mm


Tighten the 2 bolts for each bearing cap until the clearance between the crankshaft bearing cap and the cylinder block becomes less than 6 mm (0.236 in.).


i.
A076070

Using a plastic-faced hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.


j.
A184806

Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts and temporarily install the 8 crankshaft bearing cap bolts to the outside positions.


k.

Tighten the crankshaft bearing cap bolts.

HINT:

The cap bolts are tightened in 2 progressive steps.


i.
A302416
0.688,1.469 0.844,1.667 0.156,0.198 10 false 7 0.99,1.698 1.146,1.896 0.156,0.198 10 false 8 0.5,1.135 0.833,1.302 0.333,0.167 10 false 15 1.052,0.729 1.365,0.927 0.313,0.198 10 false 11 1.479,0.542 1.635,0.74 0.156,0.198 10 false 9 2.156,0.427 2.448,0.604 0.292,0.177 10 false 13 2.365,0.604 2.521,0.802 0.156,0.198 10 false 5 2.625,0.604 2.781,0.802 0.156,0.198 10 false 6 2.604,1.135 2.896,1.333 0.292,0.198 10 false 14 2.333,1.354 2.688,1.542 0.354,0.188 10 false 10 1.958,1.552 2.292,1.729 0.333,0.177 10 false 12 1.51,1.854 1.813,2.052 0.302,0.198 10 false 16 1.156,1.26 1.313,1.438 0.156,0.177 10 false 3 1.531,1.073 1.688,1.229 0.156,0.156 10 false 1 1.823,1.094 1.938,1.25 0.115,0.156 10 true 2 1.427,1.365 1.542,1.542 0.115,0.177 10 true 4

Step 1:

Uniformly tighten the 16 bolts in several steps in the order shown in the illustration.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)


ii.

Mark the front side of the crankshaft bearing cap bolts with paint.


iii.

Step 2:

Tighten the bearing cap bolts 90° in the order shown in step 1.


iv.

Check that the paint marks are now at a 90° angle to the front.



l.

Check that the crankshaft turns smoothly.


m.
A302417
0.396,0.823 0.552,1.021 0.156,0.198 10 false 3 0.844,0.552 1,0.75 0.156,0.198 10 false 2 1.156,0.333 1.313,0.531 0.156,0.198 10 false 1 1.479,0.167 1.635,0.365 0.156,0.198 10 false 4 2.667,0.792 2.823,0.99 0.156,0.198 10 false 7 2.302,0.99 2.458,1.188 0.156,0.198 10 false 6 1.917,1 2.073,1.198 0.156,0.198 10 false 5 1.427,1.5 1.583,1.698 0.156,0.198 10 false 8

Install and uniformly tighten the 8 main bearing cap bolts together with 8 new seal washers in several steps in the sequence shown in the illustration.

Torque:
26 N*m (262 kgf*cm, 19 ft.*lbf)


n.

Check that the crankshaft turns smoothly.


Hide 7.INSTALL CONNECTING ROD BEARING

a.
A302418
0.146,4.063 0.198,3.885 0.198,3.885 0.333,3.885 false 1.365,2.979 1.615,2.76 1.615,2.76 1.792,2.76 false 1.552,3.385 1.802,3.167 1.802,3.167 1.979,3.167 true 0.375,3.781 0.688,3.938 0.313,0.156 10 false *1 1.854,2.646 2.167,2.802 0.313,0.156 10 false *2 2.042,3.042 2.354,3.198 0.313,0.156 10 false *3 0.75,3.792 1.063,3.948 0.313,0.156 10 false A 1.615,3.792 1.927,3.948 0.313,0.156 10 false B
*1 Vernier Caliper
*2 Connecting Rod Cap
*3 Connecting Rod Bearing


Install the bearing to the connecting rod cap.

NOTICE:
·

Clean the contact surfaces of the bearing and connecting rod cap.


·

Do not apply engine oil to the bearing or the surface it contacts.




b.

Using a vernier caliper, measure the distance between the connecting rod cap edge and connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



c.
A302419
0.156,4.031 0.281,3.875 0.281,3.875 0.427,3.875 false 1.5,3.5 1.854,3.219 1.854,3.219 2,3.219 true 1.448,2.948 1.802,2.667 1.802,2.667 1.948,2.667 false 0.479,3.792 0.792,3.948 0.313,0.156 10 false *1 2.021,2.573 2.333,2.729 0.313,0.156 10 false *2 2.042,3.115 2.354,3.271 0.313,0.156 10 false *3 0.76,3.781 1.073,3.938 0.313,0.156 10 false A 1.625,3.76 1.938,3.917 0.313,0.156 10 false B
*1 Vernier Caliper
*2 Connecting Rod
*3 Connecting Rod Bearing


Install the bearing to the connecting rod.

NOTICE:
·

Clean the contact surface of the bearing and connecting rod.


·

Do not apply engine oil to the bearing or the surface it contacts.




d.

Using a vernier caliper, measure the distance between the connecting rod edge and connecting rod bearing edge.

Dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)



Hide 9.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons and surfaces of the connecting rod bearings.


b.
A302415
0.635,1.969 0.927,2.125 0.292,0.156 10 false *1 1.99,1.927 2.281,2.083 0.292,0.156 10 false *4 0.271,1.438 0.563,1.594 0.292,0.156 10 false *5 0.531,0.635 0.823,0.792 0.292,0.156 10 false *6 0.479,0.167 0.771,0.323 0.292,0.156 10 false *2 1.948,0.031 2.24,0.188 0.292,0.156 10 false *3
*1 No. 1 Compression Ring
*2 No. 2 Compression Ring
*3 Lower Side Rail
*4 Upper Side Rail
*5 Expander
*6 Front Mark


Check the positions of the piston ring ends.


c.
A076385
0.542,0.917 0.75,0.354 0.75,0.354 0.885,0.354 true 0.948,0.25 1.125,0.427 0.177,0.177 10 false *1
*1 Front Mark


Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.


d.
A075149
0.375,1.365 0.521,1.365 0.521,1.365 1.438,0.792 true 0.219,1.281 0.396,1.469 0.177,0.188 10 false *1
*1 Protrusion
V100135

Front Mark


Install each connecting rod cap so that the protrusion is facing the correct direction.

NOTICE:

Match each numbered connecting rod cap with the correct connecting rod.



e.

Apply a light coat of engine oil to the threads of the connecting rod cap bolts.


f.

Install the connecting rod cap bolts.

HINT:

The cap bolts are tightened in 2 progressive steps.


i.
A075150

Step 1:

Install and alternately tighten the bolts of each connecting rod cap in several steps.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


ii.

Mark the front side of each connecting rod cap bolt with paint.


iii.

Step 2:

Tighten the cap bolts 90°.


iv.

Check that the paint marks are now at a 90° angle to the front.



g.

Check that the crankshaft turns smoothly.