1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.REMOVE FUEL TANK CAP ASSEMBLY
4.REMOVE NO. 1 FUEL TANK PROTECTOR
Remove the 4 nuts and No. 1 fuel tank protector.
5.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE
Disconnect the fuel tank main tube and fuel tank return tube.
6.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Disconnect the fuel tank to filler pipe hose from the fuel tank filler pipe.
7.DISCONNECT FUEL TANK BREATHER HOSE
Disconnect the fuel tank breather hose from the fuel tank filler pipe.
8.REMOVE FUEL TANK ASSEMBLY
Place an engine lifter under the fuel tank.
Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.
Slightly lower the engine lifter.
Be careful not to cut the wiring.
| *1 | Fuel Tank Cushion |
| *2 | Wire Harness |
| *3 | Fuel Tank |
Remove the clip. Then fold back approximately half of each cushion so that the wire harness can be removed in the step below.
| *1 | Claw |
Detach the wire harness from the 6 clamps shown in the illustration.
Detach the claws of the clamps labeled A in the illustration to detach the wire harness.
Disconnect the fuel sender gauge connector.
9.REMOVE NO. 1 FUEL TANK HEAT INSULATOR
| *1 | Nut |
| *2 | Needle-nose Pliers |
| *3 | Clip |
Remove the nut.
Using needle-nose pliers, remove the 4 clips as shown in the illustration, and then remove the No. 1 fuel tank heat insulator.
10.REMOVE NO. 1 FUEL TANK CUSHION
| *1 | Clip |
Remove the clip and 2 No. 1 fuel tank cushions from the fuel tank.
11.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY
Remove the No. 1 fuel evaporation tube from the fuel tank.
12.REMOVE FUEL PUMP GAUGE RETAINER
Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.
| *1 | Fuel Tube Joint |
| *2 | Fuel Tube |
| *3 | O-Ring |
| *4 | Tube Joint Clip |
Remove any dirt and foreign matter on the fuel tube joint before performing this step.
Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube joint contains the O-rings that seal the plug.
Perform this step by hand. Do not use any tools.
Do not forcibly bend or twist the nylon tube.
Protect the disconnected parts by covering them with plastic bags and tape after disconnecting the fuel tubes.
Remove the fuel tank return tube and fuel tank main tube from the fuel tank.
| *1 | SST (Plate) |
| *2 | SST (Claw) |
| *3 | Rib |
Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.
Be sure to use 4 SST (claws) as shown in the illustration.
Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.
While pressing SST (claws) to the fuel pump gauge retainer ribs securely, install the 4 bolts.
Install SST while pressing SST (claws) against the fuel pump gauge retainer (towards the center of SST).
Install SST (handle).
Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to loosen the fuel pump gauge retainer.
When the retainer is loosened, be careful as the fuel pump will spring upward from the force of the spring.
Clean the fuel tank vent tube before this operation.
Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
Make sure to rotate SST (handle) horizontally. If SST (handle) is rotated at an angle, SST may come off.
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.
The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.
Remove the fuel pump gauge retainer.
13.REMOVE FUEL TANK VENT TUBE SUB-ASSEMBLY
Remove the fuel tank vent tube from the fuel tank.
Be careful not to bend the arm of the fuel sender gauge.
Remove the gasket from the fuel tank.
14.REMOVE FUEL TANK BREATHER HOSE
Remove the fuel tank breather hose from the fuel tank.
15.REMOVE FUEL TANK TO FILLER PIPE HOSE
Remove the fuel tank to filler pipe hose from the fuel tank.
16.REMOVE NO. 2 FUEL TANK PROTECTOR
Detach the 2 claws and remove the No. 2 fuel tank protector.