Home › Engine / Hybrid System › 1KD-FTV FUEL › FUEL INJECTOR(w/ Glow Plug Controller) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009579 1KD-FTV FUEL _0052237 FUEL INJECTOR(w/ Glow Plug Controller) A

1KD-FTV FUEL  FUEL INJECTOR(w/ Glow Plug Controller)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER

Hide 4.CHECK INJECTOR COMPENSATION CODE (for DPF)

HINT:

If the injector compensation code is not correctly registered, it may cause malfunctions.


a.

b.

Check that the compensation code of the installed injector is the same as the code registered in the ECM. If the code is not the same, register the injector compensation code on the injector (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).


Hide 5.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

a.
A271613

Remove the bolt, nut and 2 No. 2 injection pipe clamps.


b.
A271614

Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


Hide 6.REMOVE WIRING HARNESS CLAMP BRACKET

a.
A301684
1.198,0.625 1.354,0.167 1.354,0.167 1.49,0.167 true 1.542,0.042 1.854,0.24 0.313,0.198 10 false *1
*1 Wiring Harness Clamp Bracket


Detach the wire harness clamp.


b.

Remove the bolt and wiring harness clamp bracket.


Hide 7.REMOVE NO. 2 FUEL PIPE

a.

for DPF:

i.
A252276

Disconnect the vacuum switching valve connector and 2 vacuum transmitting hoses.


ii.
A252278
1.625,0.771 1.688,0.792 false
V100135

Bolt
V100136

Supply Pump Hollow Screw
V100137

Fuel Check Valve
V100138

Union Bolt


Using a 6 mm hexagon wrench, remove the supply pump hollow screw and gasket.


iii.

Remove the fuel check valve, union bolt and 2 gaskets.


iv.

Remove the 3 bolts and No. 2 fuel pipe.



b.

for i-ART:

i.

Using a 6 mm hexagon wrench, remove the supply pump hollow screw and gasket.


ii.

Remove the fuel check valve, No. 2 fuel pipe and gasket.


iii.
A271615
1.052,1.896 1.146,2.021 0.094,0.125 6 false .
V100135

Supply Pump Hollow Screw
V100136

Fuel Check Valve


Using a 6 mm hexagon wrench, remove the supply pump hollow screw and gasket.



Hide 8.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (for DPF)

a.
A254062

Remove the screw and No. 1 vacuum switching valve.


Hide 9.REMOVE NO. 3 NOZZLE LEAKAGE PIPE

a.
A252280
0.292,1.771 0.385,1.896 0.094,0.125 6 false .
V100136

Fuel Check Valve


Disconnect the 3 fuel hoses.


b.

Remove the 2 bolts.


c.

Remove the fuel check valve, gasket and No. 3 nozzle leakage pipe.


Hide 10.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

a.

for DPF:

Remove the 2 bolts.

A271616
0.107,0.063 0.291,0.218 0.185,0.155 10 *A 3.731,0.063 3.916,0.218 0.185,0.155 10 *B
*A for DPF *B for i-ART
V100136

Union Bolt - -



b.

for i-ART:

Remove the 3 bolts.


c.

Remove the union bolt, gasket and No. 2 nozzle leakage pipe.


Hide 11.REMOVE WIRING HARNESS CLAMP BRACKET (for i-ART)

a.
A271761

Detach the 6 wire harness clamps.


b.

Remove the 3 bolts and 2 wiring harness clamp brackets.


Hide 12.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A252282

Remove the 3 bolts and No. 2 cylinder head cover.


Hide 13.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:

If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.


a.
A060180

Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.


b.

Disconnect the ventilation hose.


c.
A223193

Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.


d.
A289511

Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


Hide 14.REMOVE INJECTOR ASSEMBLY

a.
A271617
0.477,0.012 0.661,0.166 0.185,0.155 10 *1 1.207,0.259 0.797,0.103 0.797,0.103 0.684,0.103 false
*1 Union Bolt


Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




b.
A271618

Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

HINT:

Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.



c.

Remove the O-ring from each injector.


d.

Remove the 4 injection nozzle seats from the cylinder head.