Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL TANK › 2012.01–2012.04
RM1840EF _51 Engine / Hybrid System _009580 2TR-FE FUEL _0052247 FUEL TANK A

2TR-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.

Install the fuel tank to filler pipe hose to the fuel tank.


Hide 2.INSTALL FUEL TANK BREATHER HOSE

a.

Install the fuel tank breather hose to the fuel tank.


Hide 3.INSTALL NO. 2 FUEL TANK PROTECTOR

a.
A252109

Install the 3 fuel tank protector cushions as shown in the illustration.


b.

Attach the 2 claws to install the protector.


Hide 4.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 6.INSTALL VENT LINE TUBE

a.

Connect the vent line hose and install the vent line tube.


Hide 7.INSTALL NO. 1 FUEL TANK CUSHION

a.
A252106

Install 2 new fuel tank cushions.


b.

Install the clip to the cushion on the front side.

HINT:

Install only 1 clip so that the cushion can be folded back and the wire harness can be installed when the fuel tank assembly is installed to the vehicle.



Hide 8.INSTALL NO. 1 FUEL TANK HEAT INSULATOR

a.

Install the No. 1 fuel tank heat insulator with 4 clips and nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 9.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank on an engine lifter and lift up the engine lifter.

A303020
2.125,2.604 2.385,2.604 false 1.594,3.333 1.854,3.333 false 2.49,2.51 2.802,2.667 0.313,0.156 10 false *1 1.385,3.24 1.698,3.396 0.313,0.156 10 false *2 2.417,3.146 2.729,3.302 0.313,0.156 10 false *3
*1 Fuel Tank Cushion *2 Wire Harness
*3 Fuel Tank - -


NOTICE:
·

Do not allow the fuel tank to contact the vehicle, especially the differential.

·

Be careful not to cut the wiring.




b.

Fold back the 2 cushion rubbers.


c.

Attach the wire harness to the 6 clamps and fuel pump and sender gauge connector.


d.

Install the cushion rubber to the front side with the remaining clip.


e.

Install the 2 fuel tank bands with the 2 pins and 2 clips.


f.

Connect the 2 fuel tank bands with the 2 bolts.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)


Hide 10.INSTALL FUEL TANK INLET PIPE SUB-ASSEMBLY

a.

Install the fuel tank inlet pipe with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 11.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the fuel tank inlet pipe.


Hide 12.CONNECT FUEL TANK BREATHER HOSE

a.

Connect the fuel tank breather hose to the fuel tank inlet pipe.


Hide 13.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE

a.

Connect the fuel tank main tube (See page Engine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Connect the fuel tank return tube (See page Engine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION).


c.

Connect the vent line hose.


Hide 14.INSTALL NO. 3 FUEL TUBE CLAMP

a.

Install the tube clamp to the fuel tube.


Hide 15.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector with the 4 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 16.INSTALL FUEL TANK CAP ASSEMBLY

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).