Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL SYSTEM › from 2012.10
RM1840EF _51 Engine / Hybrid System _009582 1GR-FE FUEL _0052263 FUEL SYSTEM G

1GR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FOR FUEL PUMP OPERATION AND FUEL LEAK

a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.

Powertrain > Engine > Active Test
Tester Display
Activate the Fuel Pump Speed Control
50004 61 4

e.

Check the fuel pump operation.

i.

Check for pressure in the fuel inlet tube from the fuel line. Check that the sound of fuel flowing in the fuel tank can be heard.

If there is no sound, check the integration relay, fuel pump, ECM and wiring connector.



f.

Disconnect the intelligent tester from the DLC3.



Hide 2.CHECK FUEL PRESSURE


b.

Discharge the fuel system pressure (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


c.

Disconnect the cable from negative (-) battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




d.
A250898
1.896,1.208 1.958,1.24 false
V100135

Pinch
V100136

Pull


Disconnect the No. 1 fuel pipe from the fuel filter (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


e.
A303039
1.531,0.615 1.708,0.542 1.708,0.542 1.906,0.542 false 2.469,1.729 2.781,1.729 false 1.427,1.146 1.573,1.26 1.573,1.26 1.719,1.26 false 2.208,0.833 2.375,0.646 2.375,0.646 2.563,0.646 false 2.896,2.719 2.896,2.927 false 0.51,2.344 0.667,2.344 0.667,2.344 0.76,2.646 false 1.531,3.938 1.688,3.938 1.688,3.938 1.76,4.135 false 2.771,3.885 2.885,3.76 2.885,3.76 3.021,3.76 false 0.323,2.26 0.635,2.417 0.313,0.156 10 false *1 1.948,0.438 2.26,0.594 0.313,0.156 10 false *2 1.792,1.188 2.104,1.344 0.313,0.156 10 false *3 2.302,1.625 2.615,1.781 0.313,0.156 10 false *4 2.615,0.552 2.927,0.708 0.313,0.156 10 false *5 3.063,3.667 3.375,3.823 0.313,0.156 10 false *6 2.833,2.979 3.146,3.135 0.313,0.156 10 false *1 1.344,3.844 1.656,4 0.313,0.156 10 false *1
*1 SST (Hose)
*2 SST (Clip)
*3 SST (T-Joint)
*4 SST (Gauge)
*5 Fuel Tube
*6 Fuel Tube Connector


Install SST (pressure gauge) as shown in the illustration.

SST
09268-31014  (95336-08070, 09268-41120, 09268-41500)
09268-45014  (09268-41200, 09268-41220, 90467-13001)


f.

Wipe off any gasoline.


g.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



h.

Operate the fuel pump.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control / ON.

Powertrain > Engine > Active Test
Tester Display
Activate the Fuel Pump Speed Control
50004 61 4


i.

Measure the fuel pressure.

Standard fuel pressure:

281 to 287 kPa (2.87 to 2.93 kgf/cm2, 41 to 42 psi)


If the pressure is higher than the specification, replace the fuel pressure regulator.

If the pressure is below the specification, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator.


j.

Start the engine.


k.

Measure the fuel pressure.

Standard fuel pressure:

281 to 287 kPa (2.87 to 2.93 kgf/cm2, 41 to 42 psi)


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.


l.

Stop the engine.


m.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or higher


If the pressure is not as specified, check the fuel pump, pressure regulator and/or injectors.


n.

Disconnect the cable from the negative (-) battery terminal and carefully remove SST and the fuel tube connector to prevent gasoline from spraying.


o.

Connect the No. 1 fuel hose to the fuel filter (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).