Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL INJECTOR › from 2012.04
RM1840EF _51 Engine / Hybrid System _009582 1GR-FE FUEL _0052264 FUEL INJECTOR G

1GR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.


Hide 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.
A267747
0.656,2.531 0.656,2.24 false 1.604,1.635 1.5,1.635 1.5,1.635 1.5,2.906 false 1.604,2.229 1.5,2.229 false 2.688,1.979 2.688,2.177 false 1.094,1.417 1.208,1.417 1.208,1.417 1.365,1.542 false 1.198,0.99 1.406,0.99 1.406,0.99 1.802,1.302 false 1.865,0.542 2.021,0.542 2.021,0.542 2.25,1.031 false 3.125,1.365 3,1.365 3,1.365 2.74,1.74 false 1,0.917 1.167,1.104 0.167,0.188 10 false *3 0.615,2.583 0.802,2.76 0.188,0.177 10 false *4 2.625,2.208 2.802,2.396 0.177,0.188 10 false *5 3.188,1.26 3.385,1.458 0.198,0.198 10 false *1 1.646,0.448 1.823,0.615 0.177,0.167 10 false *2 0.875,1.333 1.052,1.5 0.177,0.167 10 false *2 1.448,2.938 1.646,3.135 0.198,0.198 10 false *1
*1 SST (Hose Band)
*2 SST (Hose)
*3 SST (3 Way)
*4 SST (Union)
*5 SST (Fuel Tube Connector)


Check the injector injection.

CAUTION:
·

This test involves high-pressure fuel and electricity.

·

Take every precaution regarding safe handling of both the fuel and the electrical parts.

·

Perform this test in a safe area and avoid any sparks or flame.

·

Do not smoke.



i.

Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41091, 09268-41120, 09268-41500, 09268-41700, 95336-08070)


ii.

Discharge the fuel system pressure (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


iii.

Disconnect the fuel inlet hose (fuel tube connector) from the fuel filter.


iv.

Remove the bolt and disconnect the fuel pressure regulator from the fuel delivery pipe.

NOTICE:

Do not disconnect the fuel hose No. 2 from the fuel pressure regulator.



v.
A267748
1.948,1.635 1.406,1.635 false 2.667,0.542 2.563,0.542 2.563,0.542 2.323,0.74 false 2.74,0.438 2.938,0.625 0.198,0.188 10 false *1 1.177,1.542 1.375,1.729 0.198,0.188 10 false *2
*1 SST (Fuel Tube Connector)
*2 Fuel Filter


Connect SST to the fuel filter.

SST
09268-31014  (09268-41500)

CAUTION:

Always read the precautions before connecting the fuel tube connector.



vi.
A267749
2.375,1.594 2.25,1.594 2.25,1.594 2.25,0.885 false 0.823,1.906 0.438,1.906 0.438,1.906 0.313,1.813 false 2.802,0.75 2.802,0.635 2.802,0.635 2.563,0.51 false 0.833,0.438 1.146,0.438 false 1.917,0.115 2.167,0.115 2.167,0.115 2.531,0.271 false 0.635,0.354 0.813,0.531 0.177,0.177 10 false *4 0.896,1.813 1.083,1.979 0.188,0.167 10 false *5 2.448,1.5 2.615,1.688 0.167,0.188 10 false *3 1.698,0.031 1.875,0.208 0.177,0.177 10 false *1 2.74,0.792 2.927,0.969 0.188,0.177 10 false *2
*1 SST (Hose)
*2 SST (Hose Band)
*3 SST (Union)
*4 Fuel Pressure Regulator
*5 Fuel Return Hose


Connect SST (hose) to the fuel inlet of the fuel pressure regulator with another SST (union) and the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


vii.

Connect the fuel return hose to the fuel outlet of the fuel pressure regulator.


viii.

Install the O-ring to the fuel injector.


ix.
A267750
2.021,2.813 2.021,3.031 false 0.396,0.76 0.823,0.76 false 1.646,0.354 1.417,0.354 1.417,0.354 1.177,1.031 false 3.021,2.156 3.021,1.948 3.021,1.948 2.698,1.75 false 0.281,2.5 0.281,2.365 0.281,2.365 0.781,2.104 false 0.177,0.667 0.365,0.844 0.188,0.177 10 false *2 0.219,2.563 0.396,2.729 0.177,0.167 10 false *3 1.958,3.063 2.146,3.24 0.188,0.177 10 false *5 2.969,2.177 3.146,2.344 0.177,0.167 10 false *4 1.719,0.25 1.906,0.427 0.188,0.177 10 false *1
*1 SST (Hose Band)
*2 SST (Hose)
*3 SST (Adapter)
*4 SST (Clamp)
*5 Vinyl Tube


Connect SST (adapter and hose) to the fuel injector and hold the fuel injector and adapter with SST (clamp).

SST
09268-31014  (09268-41141, 09268-41410, 09268-41700, 95336-08070)


x.
A267752
1.438,2.01 1.26,2.01 1.26,2.01 1.26,1.813 false 2.615,1.469 2.615,1.323 2.615,1.323 2.344,0.854 true 2.552,1.5 2.729,1.698 0.177,0.198 10 false *a 1.49,1.906 1.667,2.063 0.177,0.156 10 false *1
*1 SST (Tie Band)
*a Lock


Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



xi.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


xii.

Install a vinyl tube to the injector.

CAUTION:

Install a suitable vinyl tube to the injector to contain any gasoline spray.



xiii.

Put the fuel injector into a graduated cylinder.

HINT:

Install a suitable vinyl tube onto the fuel injector to contain any gasoline spray.



xiv.

Operate the fuel pump.


xv.
A267751
1.99,0.875 1.99,0.74 1.99,0.74 2.146,0.5 false 1.906,0.917 2.094,1.115 0.188,0.198 10 false *1
*1 SST (Wire)
V100135

Connect


Connect SST (wire) to the fuel injector and the battery for 15 seconds and measure the injection volume with a graduated cylinder. Test each injector 2 or 3 times.

SST
09842-30080  

Standard injection volume:

76 to 91 cm3 (4.6 to 5.5 cu in.) per 15 seconds


Difference between each fuel injector:

15 cm3 (0.9 cu in.) or less


NOTICE:
·

Make sure that SST (EFI inspection wire H) is securely connected.

·

Always turn the voltage on and off on the battery side, not the fuel pump side.



If the result is not as specified, replace the fuel injector assembly.



b.

Check for fuel leakage.

i.

In the condition above, disconnect the test probes of SST (wire) from the battery and check the rate of fuel leakage from the fuel injector.

Standard fuel leakage:

1 drop or less per 12 minutes


If the fuel leakage is not as specified, replace the fuel injector assembly.