Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL TANK › from 2012.10
RM1840EF _51 Engine / Hybrid System _009582 1GR-FE FUEL _0052270 FUEL TANK A

1GR-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.

Install the fuel tank to filler pipe hose to the fuel tank.


Hide 2.INSTALL FUEL TANK BREATHER HOSE

a.

Install the fuel tank breather hose to the fuel tank.


Hide 3.INSTALL NO. 2 FUEL TANK PROTECTOR

a.

Attach the 2 claws and install the protector.


Hide 4.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 6.INSTALL NO. 2 FUEL TANK CUSHION

a.
A303189

Install a new No. 2 fuel tank cushion.


Hide 7.INSTALL NO. 1 FUEL TANK CUSHION

a.

Install a new No. 1 fuel tank cushions.


b.

Install the clip to the cushion on the front side.

HINT:

Install only 1 clip so that the cushion can be folded back and the wire harness can be installed when the fuel tank assembly is installed to the vehicle.



Hide 8.INSTALL NO. 1 FUEL TANK HEAT INSULATOR

a.

Install the No. 1 fuel tank heat insulator with the 4 new clips and nut.


Hide 9.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank on a engine lifter and lift up the engine lifter.

A303136
2.281,2.344 2.615,2.344 false 1.604,3.25 1.938,3.25 false 1.135,1.49 1.448,1.646 0.313,0.156 10 false *1 2.688,2.26 3,2.417 0.313,0.156 10 false *2 1.427,3.146 1.74,3.302 0.313,0.156 10 false *3 2.438,3.063 2.75,3.219 0.313,0.156 10 false *4
*1 Clip *2 Fuel Tank Cushion
*3 Wire Harness *4 Fuel Tank


NOTICE:
·

Do not allow the fuel tank to contact the vehicle, especially the differential.

·

Be careful not to cut the wiring.




b.

Fold back the 2 cushion rubbers.


c.

Connect the 6 harness clips and fuel pump connector to the fuel tank.


d.

Install the cushion rubber on the front side with the remaining clip.


e.

Install the 2 No. 1 fuel tank bands with the 2 pipes and 2 clips.


f.

Connect the 2 No. 1 fuel tank bands with the 2 bolts.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)


Hide 10.INSTALL FUEL TANK FILLER PIPE

a.

Install the fuel tank filler pipe with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 11.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the filler pipe hose to the fuel tank filler pipe.


Hide 12.CONNECT FUEL TANK BREATHER HOSE

a.

Connect the fuel tank breather hose to the fuel tank filler pipe.


Hide 13.CONNECT FUEL MAIN TUBE AND FUEL RETURN TUBE

NOTICE:

Before installing the tube connectors to the pipes, check the connectors for damage and foreign matter.


a.

Connect the fuel main tube and fuel return tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Connect the vent line hose.


Hide 14.INSTALL NO. 3 FUEL TUBE CLAMP

a.

Install the No. 3 fuel tube clamp to the fuel tube.


Hide 15.INSTALL FUEL TANK CAP ASSEMBLY

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).