Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL TANK › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009582 1GR-FE FUEL _0052270 FUEL TANK A

1GR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.REMOVE FUEL TANK CAP ASSEMBLY

Hide 5.REMOVE NO. 3 FUEL TUBE CLAMP

a.
G038853

Remove the No. 3 fuel tube clamp from the fuel tube.


Hide 6.DISCONNECT FUEL MAIN TUBE AND FUEL RETURN TUBE

a.
A250907

Disconnect the fuel main tube and fuel return tube (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Disconnect the vent line hose.


Hide 7.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A099799

Disconnect the filler pipe hose from the fuel tank filler pipe.


Hide 8.DISCONNECT FUEL TANK BREATHER HOSE

a.

Disconnect the breather hose from the fuel tank filler pipe.


Hide 9.REMOVE FUEL TANK FILLER PIPE

a.

Remove the bolt and filler pipe.


Hide 10.REMOVE FUEL TANK ASSEMBLY

a.
A099811

Place a engine lifter under the fuel tank.


b.

Remove the 2 bolts, 2 clips, 2 pins and 2 No. 1 fuel tank bands.


c.

Slightly lower the engine lifter.

NOTICE:

Be careful not to cut the wiring.



d.
A303134
2.083,2.781 2.354,2.781 false 1.302,4.125 1.573,4.125 false 2.438,2.677 2.75,2.833 0.313,0.156 10 false *1 2.313,3.885 2.625,4.042 0.313,0.156 10 false *2 1.104,4.042 1.417,4.198 0.313,0.156 10 false *3
*1 Fuel Tank Cushion
*2 Fuel Tank
*3 Wire Harness


Remove the clip. Then fold back approximately half of each cushion rubber so that the wire harness can be removed in the next step.


e.
A303135
0.948,3.708 1.146,4.156 1.146,4.156 1.333,4.156 true 1.406,4.073 1.719,4.229 0.313,0.156 10 false *1 1.271,1.396 1.438,1.625 0.167,0.229 10 false A 1.813,1.521 1.979,1.75 0.167,0.229 10 false A 2.177,1.406 2.344,1.635 0.167,0.229 10 false A
*1 Claw


Detach the wire harness from the 6 clamps shown in the illustration.

HINT:

Detach the claw of the clamps labeled A in the illustration to detach the wire harness.



f.

Disconnect the fuel pump connector.


Hide 11.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
A250909
0.969,2.969 0.865,2.969 0.865,2.969 0.729,3.25 false 2.063,2.979 1.958,2.979 1.958,2.979 1.823,3.25 false 2.906,2.938 3.083,2.938 3.083,2.938 2.948,3.208 false 2.854,1.781 2.854,1.49 2.854,1.49 3.125,1.229 true 0.448,0.323 2.615,0.323 2.615,0.323 2.615,1.063 true 2.229,1.417 2.229,0.333 true 1.792,1.104 1.792,0.333 true 0.958,1.365 0.958,0.333 true 1.031,2.865 1.219,3.021 0.188,0.156 10 false *1 2.125,2.885 2.313,3.042 0.188,0.156 10 false *1 2.698,2.854 2.875,3.01 0.177,0.156 10 false *1 0.229,0.229 0.417,0.385 0.188,0.156 10 false *2 2.792,1.813 2.979,1.969 0.188,0.156 10 false *3
*1 Needle-nose Pliers
*2 Clip
*3 Nut


Using needle-nose pliers, remove the 4 clips and nut as shown in the illustration, and then remove the No. 1 fuel tank heat insulator.


Hide 12.REMOVE NO. 1 FUEL TANK CUSHION

a.
G038622

Remove the clip and No. 1 fuel tank cushions.


Hide 13.REMOVE NO. 2 FUEL TANK CUSHION

a.

Remove the No. 2 fuel tank cushion.


Hide 14.REMOVE FUEL PUMP GAUGE RETAINER

Hide 15.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 16.REMOVE NO. 2 FUEL TANK PROTECTOR

a.
A252108

Detach the 2 claws and remove the protector.


Hide 17.REMOVE FUEL TANK BREATHER HOSE

a.
A191370

Remove the fuel tank breather hose from the fuel tank.


Hide 18.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.

Remove the fuel tank to filler pipe hose from the fuel tank.