When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
After removing the injection pipes, clean them with a brush and compressed air.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.DRAIN ENGINE COOLANT (w/ EGR Cooler)
4.REMOVE DIESEL THROTTLE BODY ASSEMBLY
5.DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)
| *1 | No. 4 Water By-pass Hose |
| *2 | No. 3 Water By-pass Hose |
Remove the clamp.
Disconnect the No. 3 water by-pass hose from the EGR cooler.
6.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)
Disconnect the No. 4 water by-pass hose from the EGR cooler.
7.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/ EGR Cooler)
8.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)
Remove the 3 bolts and No. 2 intake air connector bracket.
9.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/o EGR Cooler)
10.DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)
Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with wire harness.
11.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (for EGR)
w/ EGR Cooler:
Disconnect the 2 connectors.
Disconnect the 5 vacuum hoses.
Remove the bolt and No. 1 gas filter with the gas filter bracket.
Remove the 2 bolts and electric vacuum regulating valve bracket together with the vacuum damper.
Do not remove the electric vacuum regulating valve from the bracket.
w/o EGR Cooler:
Disconnect the connector.
Disconnect the 2 vacuum hoses.
Remove the 2 bolts and electric vacuum regulating valve together with the bracket.
Do not remove the electric vacuum regulating valve from the bracket.
12.REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)
Remove the 3 nuts, No. 2 intake air connector and gasket.
13.REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler)
Remove the 3 bolts, intake air connector and 2 gaskets.
14.REMOVE INTAKE AIR CONNECTOR (w/o EGR Cooler)
15.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)
Disconnect the vacuum hose from the No. 2 EGR valve.
Remove the bolt, 2 nuts, electric EGR control valve with No. 2 EGR valve and EGR cooler.
Remove the gasket from the cylinder head.
16.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o EGR Cooler)
| *1 | Gasket |
Remove the 2 bolts, 2 nuts, No. 1 EGR pipe and 2 gaskets.
17.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
w/ EGR Cooler:
Remove the 2 bolts, electric EGR control valve and gasket.
w/o EGR Cooler:
Disconnect the EGR valve position sensor connector.
Remove the electric EGR control valve and gasket.
18.REMOVE EGR VALVE ADAPTER (w/ EGR Cooler)
Using a 6 mm hexagon wrench, remove the 3 hexagon bolts, 3 plate washers, EGR valve adapter and gasket.
19.REMOVE NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)
Using a 5 mm hexagon wrench, remove the hexagon bolt, No. 2 EGR valve and gasket.