Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009588 1KD-FTV INTAKE / EXHAUST _0052321 EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF) D

1KD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER(w/o DPF)  SYSTEM DESCRIPTION  


This section should be used as a guide for troubleshooting when the turbocharger is suspected as the cause of a problem.

OUTLINE OF TURBOCHARGER FAILURE


a.

State of Turbocharger Failure Repair:

It is well known that turbocharger malfunctions cause many symptoms as shown below. However, the mechanisms resulting in these symptoms that indicate turbocharger malfunctions are not well understood. As a result, many unnecessary turbocharger replacements and other repairs are being performed due to lack of knowledge about the turbocharger and turbocharger failure. Therefore, knowing the facts regarding turbocharger malfunctions is useful for making effective repairs and saving time.


b.

Turbocharger Failure Classification

Symptom Symptom Description See page
Noise Whistling noise Continuous high- pitched noise proportional to engine speed
·

"Noise" listed below

·

"Turbocharger Noise" flowchart (See page (Click here))


Whining noise Relatively low-pitched noise compared to whistling noise
Oil leak External oil leak Oil leak on surface of turbocharger visible from outside of turbocharger
·

"Oil Leak and White Smoke" listed below

·

"Turbocharger Oil Leak and White Smoke" flowchart (See page (Click here))


Internal oil leak Oil leak from inside of bearing housing to inside of either compressor housing or turbine housing through seal ring
White smoke Oil smoke Oil smoke is emitted from exhaust pipe
Unburned fuel smoke Unburned fuel smoke is emitted from exhaust pipe
Black smoke Black smoke is emitted from exhaust pipe
·

"Black Smoke" listed below

·

"Black Smoke Emitted" flowchart (See page (Click here))


Lack of power or hesitation Vehicle does not reach target speed
·

"Lack of Power and Hesitation" listed below

·

"Lack of Power or Hesitation" flowchart (See page (Click here))


Poor acceleration
Shock during acceleration
MIL turns on
DTC
P0046 Control Solenoid Circuit Range / Performance Diagnostic Trouble Code Chart (See page (Click here))
P0047 Boost Control "A" Circuit Low
P0048 Boost Control "A" Circuit High
P0299 Underboost
P1251 Overboost Condition (Too High)
P1264 VN Turbo Controller Malfunction
P2563 Position Sensor "A" Circuit Range/Performance
P2564 Position Sensor "A" Circuit Low
P2565 Position Sensor "A" Circuit High
P2588 Position Sensor "B" Circuit Low
P2589 Position Sensor "B" Circuit High

HINT:

This table shows only typical problems related to the turbocharger.




NOISE


Description
Probable Cause Probable Failed Component
Turbine shaft imbalance Turbocharger
Leakage from intake line Intake line
Gear noise
(Mistaken for turbocharger noise)
·

Gear inside engine

·

Transmission gear

·

Vacuum pump gear



HINT:

It is easy to confirm whether the turbocharger is the cause of the noise or not, and confirming this before inspecting the turbocharger or removing it from the engine is an effective way to reduce troubleshooting time.


a.

Connect the intelligent tester to the DLC3.

HINT:

The software version installed on the intelligent tester must be V2009.2 or later.



b.

Start the engine and warm it up.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VN Turbo Open.

Powertrain > Engine > Active Test
Tester Display
Activate the VN Turbo Open
50004 61 182

e.

Perform the Active Test and rev the engine up several times.


f.

Check whether the noise is reduced or not compared with the noise under the condition that the Active Test is not performed.

Result
Result Cause of Noise
The noise is reduced (or disappears) Turbocharger
The noise does not change Not turbocharger (other parts)

HINT:

Refer to the "Turbocharger Noise" flowchart (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>Turbocharger Noise).




OIL LEAK AND WHITE SMOKE


Description
Oil Leak Type Description Main Trouble Area
Internal oil leak
(White smoke)
·

Oil leak from bearing housing to either compressor housing (intake side) or turbine housing (exhaust side) through seal rings.

·

This type of oil leak is not visible from outside of turbocharger.

·

If oil leak occurs from turbine side seal, large amount of white smoke is emitted from exhaust pipe.


·

Compressor side seal ring

·

Turbine side seal ring

·

Clogging of oil drain

·

Shaft breakage

·

Shaft or bearing seizure

·

Compressor impeller damage


External oil leak
·

Oil leak from inside of turbocharger to outside of turbocharger.

·

Includes oil leaks visible from outside of turbocharger.


·

FIPG sealing part

·

Oil pipe flange

·

Oil pipe union

·

Hose connection of intake pipe



A301806C01
3.615,1.094 4.094,0.188 4.094,0.188 4.26,0.188 true 3.792,1.969 4.729,0.188 4.729,0.188 4.917,0.188 true 5.104,0.542 5.531,0.542 false 4.583,2 6.26,2 true 4.906,2.438 6.313,2.438 true 1.594,0.667 2.021,0.667 false 1.24,2.01 1.667,2.01 true 1.167,2.365 2.531,2.365 true 3.646,2.719 3.646,3.083 true 2.917,3.844 2.917,4.208 false 1.104,1.365 1.302,1.365 1.302,1.365 3,1.906 true 1.396,0.583 1.708,0.74 0.313,0.156 10 false *1 6.354,1.896 6.667,2.052 0.313,0.156 10 false *2 1.042,1.917 1.354,2.073 0.313,0.156 10 false *3 0.938,2.271 1.25,2.427 0.313,0.156 10 false *4 4.344,0.083 4.656,0.24 0.313,0.156 10 false *5 4.99,0.083 5.302,0.24 0.313,0.156 10 false *6 3.573,3.135 3.885,3.292 0.313,0.156 10 false *7 2.833,4.219 3.146,4.375 0.313,0.156 10 false *8 5.646,0.438 5.958,0.594 0.313,0.156 10 false *9 6.354,2.333 6.823,2.49 0.469,0.156 10 false *10 0.396,4.063 0.708,4.219 0.313,0.156 10 false *a 4.688,4.083 5,4.24 0.313,0.156 10 false *b 0.906,1.271 1.219,1.427 0.313,0.156 10 false *2 2.688,1.167 3,1.365 0.313,0.198 10 false *a
*1 Compressor Housing *2 Seal Ring
*3 Compressor Inlet *4 Compressor Impeller
*5 Bearing Housing *6 Turbine Shaft
*7 Oil Drain (Outlet) *8 FIPG Sealing Part
*9 Turbine Housing *10 Turbine Wheel
*a Internal oil leak to compressor housing *b Internal oil leak to turbine housing


HINT:
·

The above illustration is an example.

·

When there is an internal oil leak, white smoke is emitted from the exhaust pipe and oil is consumed excessively. However, the cause of white smoke or excessive oil consumption can vary. Therefore, do not assume that the turbocharger is the cause of the problem when there is white smoke emission or excessive oil consumption.

·

When there is an external oil leak, the sources of the oil leak are limited to the points mentioned in the table above. If oil leaks from a FIPG sealing part, replace the turbocharger. If oil leaks from an oil pipe flange or hose connection, do not replace the turbocharger, but confirm and repair the flange or hose.

·

Refer to the "Turbocharger Oil Leak and White Smoke" flowchart (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>Turbocharger Oil Leak and White Smoke).




BLACK SMOKE


a.

Malfunctions are classified into 2 types as shown below.

Description
Malfunction Main Fault
Intake air volume shortage Insufficient mass air flow due to, for example, excessively low boost pressure, which results in fuel injection volume being relatively excessive with respect to mass air flow.
Excessive injection volume Excessive injection volume or incorrect injection timing due to fuel system trouble.


b.

Main Components Related to Black Smoke:

Possible Faulty Component Main Fault
Turbocharger Abnormally low boost pressure
Intake system Leakage between turbocharger and intake manifold
Fuel system
·

Excessive fuel injection volume

·

Incorrect fuel injection timing


EGR valve Stuck or does not close completely
Diesel throttle Stuck or does not move smoothly

HINT:

The components listed above are only the main ones. Not all the components potentially related to black smoke are listed. For details regarding the troubleshooting of black smoke, refer to the "Black Smoke Emitted" flowchart (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>Black Smoke Emitted).



c.

Relation between Turbocharger and Black Smoke:

If the boost pressure is below normal due to a turbocharger failure, black smoke may occur due to a lack of mass air flow. However, abnormally low boost pressure can be caused by the failure of various components such as intake lines, the EGR valve, etc. Therefore, do not assume that the turbocharger is the cause of abnormally low boost pressure, but check all the components possibly related to abnormally low boost pressure. Components related to abnormal boost pressure are shown in a chart listed in the On-vehicle Inspection for the Intake System (See page Engine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION). For simple and effective troubleshooting, refer to the chart before starting troubleshooting.



LACK OF POWER AND HESITATION


a.

Malfunctions are classified into 2 types as shown below.

Description
Malfunction Main Fault
Intake air volume shortage Insufficient mass air flow due to, for example, excessively low boost pressure, which results in fuel injection volume being restricted.
Abnormal injection volume Abnormal injection volume or timing due to fuel system trouble.


b.

Main Components Related to Lack of Power and Hesitation:

Possible Faulty Component Main Fault
Turbocharger
·

Abnormal boost pressure

·

VN does not move smoothly


Intake system
·

Leakage between turbocharger and intake manifold

·

Clogging or blockage of intake line


Fuel system
·

Abnormal injection volume

·

Incorrect fuel injection timing


EGR valve Stuck or does not close completely
Diesel throttle Stuck or does not move smoothly
Exhaust system Clogging of exhaust line

HINT:
·

The components listed above are only the main ones. Not all the components potentially related to lack of power and hesitation are listed. For details regarding the troubleshooting of lack of power and hesitation, refer to the "Lack of Power or Hesitation" flowchart (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>Lack of Power or Hesitation).

·

If an obvious malfunction (lack of power) has not been reproduced, test drive vehicle of the same model which has the same engine, and compare the engine conditions and performance. If there is no great difference in engine performance, explain to the customer that the lack of power the customer mentioned is not abnormal.




c.

Relation between Turbocharger and Abnormal Boost Pressure:

If the boost pressure is below normal due to a turbocharger failure, a lack of power could occur due to an intake air volume shortage. However, abnormal boost pressure can be caused by the failure of various components such as intake lines, the EGR valve, etc. Therefore, do not assume that the turbocharger is the cause of abnormal boost pressure, but check all the components possibly related to abnormal boost pressure. Components related to abnormal boost pressure are shown in a chart listed in the On-vehicle Inspection for the Intake System (See page Engine / Hybrid System>1KD-FTV INTAKE / EXHAUST>INTAKE SYSTEM(w/o Glow Plug Controller)>ON-VEHICLE INSPECTION). For simple and effective troubleshooting, refer to the chart before starting troubleshooting.



MIL TURNS ON


If a DTC related to a turbocharger malfunction is stored, refer to the troubleshooting section for each DTC (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DIAGNOSTIC TROUBLE CODE CHART).


BRIEF OUTLINE OF TURBOCHARGER OPERATION AND CONSTRUCTION


a.

A turbocharger is a component used to supply a larger air volume to the cylinders by recovering exhaust gas energy using a turbine coaxially connected to a compressor.


b.

Principle of Turbocharging:

Boost pressure is proportional to turbocharger speed, because the intake air is accelerated by centrifugal force generated by the rotation of the compressor and the increased kinetic energy, i.e. the velocity of the intake air, is converted to pressure energy by the diffuser located around the outlet of the compressor impeller. The compressor is driven by the turbine connected coaxially by the turbine shaft. The turbine is driven by exhaust gas energy. Therefore, when the turbocharger begins boosting the intake air, a larger air volume is supplied to the cylinders and more fuel can be injected. As a result, more exhaust energy will be available and the turbocharger boost increases.

A227153C04
1.979,2.552 2.073,2.552 2.073,2.552 2.438,2.781 false 2.51,0.177 2.667,0.177 2.667,0.177 3.281,0.521 true 5.521,0.125 5.396,0.125 5.396,0.125 4.74,0.552 true 4.156,4.698 4.063,4.698 4.063,4.698 3.708,5.26 true 2.917,7.406 3.021,7.406 3.021,7.406 3.823,6.073 true 2.271,0.104 2.5,0.281 0.229,0.177 10 false *1 5.583,0.031 5.813,0.208 0.229,0.177 10 false *2 1.885,1.042 2.115,1.219 0.229,0.177 10 false *3 3.979,2.281 4.208,2.458 0.229,0.177 10 false *4 3.979,3.198 4.208,3.375 0.229,0.177 10 false *5 1.823,2.458 2.052,2.635 0.229,0.177 10 false *6 4.229,4.615 4.458,4.792 0.229,0.177 10 false *7 2.667,7.323 2.896,7.5 0.229,0.177 10 false *8 4.896,1.958 5.125,2.135 0.229,0.177 10 false *a 4.073,5.75 4.302,5.927 0.229,0.177 10 false *b
*1 Compressor *2 Turbine
*3 Air Cleaner *4 Exhaust Manifold
*5 Intake Manifold *6 Intercooler
*7 Diffuser *8 Compressor
*a See HINT below *b Intake air flow


HINT:
·

*a: If sufficient exhaust gas energy is not available, the turbocharger cannot generate the required boost pressure even when the turbocharger does not have a malfunction.

·

Considering the fact that the turbocharger is driven by exhaust gas energy, if sufficient exhaust gas is not available due to abnormal injection volume, etc., the required boost pressure will not be available even when the turbocharger does not have a malfunction. Therefore, when boost pressure is abnormally low, checking all the related components using the correct troubleshooting procedure is necessary for simple and effective repair.




c.

Boost Pressure Control:

The amount of energy the turbine can obtain from the exhaust gas is proportional to the expansion ratio, which is defined as the ratio of the turbine inlet exhaust gas pressure to the pressure at the turbine outlet.

To control boost pressure, a Variable Nozzle (VN) is used just upstream of the turbine wheel inlet, and controls the expansion ratio. If the VN is closed, the gap between neighboring vanes is narrowed and the turbine inlet exhaust gas pressure, and correspondingly the expansion ratio, increases. Therefore, when the VN is closed, the turbine receives more energy, and the turbine speed and boost pressure increase. On the other hand, if the VN is opened, the turbine inlet exhaust gas pressure decreases, and the turbine speed and boost pressure decrease. The VN is actuated by a DC motor. The ECM controls the VN opening angle through the turbo motor driver in accordance with the engine condition. When a high engine power is required, the actuation rod is moved by the actuator to close the VN and boost pressure increases.

A301789C01
2.427,2.229 2.896,2.781 2.896,2.781 2.896,2.938 true 1.635,1.667 1.021,1 1.021,1 0.854,1 true 1.844,1.469 1.51,0.458 1.51,0.458 1.375,0.458 true 5.198,1.438 4.865,0.427 4.865,0.427 4.729,0.427 true 5.167,1.729 4.5,0.948 4.5,0.948 4.323,0.948 true 5.823,2.219 6.292,2.771 6.292,2.771 6.292,2.927 true 1.156,0.365 1.469,0.521 0.313,0.156 10 false *1 2.823,2.979 3.135,3.135 0.313,0.156 10 false *2 0.646,0.917 0.958,1.073 0.313,0.156 10 false *3 4.094,0.865 4.406,1.021 0.313,0.156 10 false *4 1.656,0.115 1.969,0.271 0.313,0.156 10 false *a 5.104,0.115 5.417,0.271 0.313,0.156 10 false *b 2.76,1.813 3.073,1.969 0.313,0.156 10 false *c 6.229,2.979 6.542,3.135 0.313,0.156 10 false *2 4.521,0.333 4.833,0.49 0.313,0.156 10 false *1 6.167,1.802 6.479,1.958 0.313,0.156 10 false *c
*1 VN (Variable Nozzle) *2 Turbine Wheel
*3 Narrow Gap *4 Wide Gap
*a VN Closed *b VN Open
*c Exhaust Gas Flow - -


HINT:

If the VN becomes stuck open, the necessary boost pressure will not be available. If the VN becomes stuck closed, overboost will occur.



d.

Mechanical Construction of Turbocharger:

A227154C01
1.635,6.052 1.729,6.052 1.729,6.052 2.479,4.917 true 4.708,2.208 4.615,2.208 4.615,2.208 3.958,4.646 true 4.906,2.479 4.813,2.479 4.813,2.479 4.302,4.271 true 5.073,2.74 4.979,2.74 4.979,2.74 4.865,3.146 false 4.385,2.021 4.292,2.021 4.292,2.021 3.635,4.49 true 4.115,1.781 4.01,1.781 4.01,1.781 3.448,3.667 true 2.448,2.25 2.542,2.25 2.542,2.25 3.125,4.281 true 2.323,2.552 2.417,2.552 2.417,2.552 2.927,4.344 true 2.01,3.198 1.583,3.198 false 5.51,4.927 4.667,4.927 true 4.51,5.396 4.51,6.958 true 3.49,5.198 3.49,6.594 true 2.125,6.375 2.219,6.375 2.219,6.375 3.302,4.708 true 3.76,0.406 3.26,0.406 false 3.917,1.198 2.885,1.198 true 3.865,0.313 4.083,0.5 0.219,0.188 10 false *1 4,1.115 4.219,1.302 0.219,0.188 10 false *2 4.208,1.688 4.427,1.875 0.219,0.188 10 false *3 4.479,1.927 4.698,2.115 0.219,0.188 10 false *4 4.76,2.104 4.99,2.323 0.229,0.219 10 false *5 4.948,2.396 5.177,2.583 0.229,0.188 10 false *6 5.115,2.646 5.333,2.833 0.219,0.188 10 false *7 5.552,4.823 5.771,5.01 0.219,0.188 10 false *8 2.208,2.156 2.427,2.344 0.219,0.188 10 false *9 1.802,2.438 2.031,2.656 0.229,0.219 10 false *10 1.271,3.125 1.552,3.313 0.281,0.188 10 false *11 1.323,5.958 1.604,6.146 0.281,0.188 10 false *12 1.167,4.646 1.448,4.833 0.281,0.188 10 false *b 1.635,6.271 1.906,6.49 0.271,0.219 10 false *13 3.385,6.656 3.667,6.844 0.281,0.188 10 false *14 4.417,7.031 4.698,7.219 0.281,0.188 10 false *15 4.979,2.094 5.24,2.302 0.26,0.208 10 false *a 5.177,2.375 5.438,2.583 0.26,0.208 10 false *c 2.094,2.427 2.354,2.635 0.26,0.208 10 false *c 1.896,6.26 2.156,6.469 0.26,0.208 10 false *a
*1 VN Actuator (DC Motor) *2 VN Actuating Rod
*3 Bearing Housing *4 Turbine Shaft
*5 Radial Bearing *6 Turbine Side Seal Ring
*7 Turbine Housing *8 Turbine Wheel
*9 Thrust Bearing *10 Compressor Side Seal Ring
*11 Compressor Housing *12 Compressor Impeller
*13 Radial Bearing *14 Oil Drain
*15 VN (Variable Nozzle) - -
*a See HINT below *b See HINT below
*c See HINT below - -
V100135

Exhaust Gas Flow
V100136

Intake Air Flow


HINT:
·

The above illustration is an example.

·

*a: The clearances of the radial bearing and thrust bearing are on the order of 100 μm, and for the accurate measurement of these clearances, an accurate process and accurate tools are essential.

·

*b: A certain amount of oil mist from PCV gas is contained in the intake air. Therefore, a certain amount of oil at the inlet of the compressor is normal, and is not an oil leak.

·

*c: The seal rings are C-shaped rings just like piston rings, and have a gap. Therefore, complete sealing is impossible by the seal rings alone. The oil is sealed in with the aid of the boost pressure in the compressor housing, and the exhaust gas pressure in the turbine housing. These pressures prevent oil from exiting the bearing housing through the gap of the seal rings. Therefore, if the turbine shaft is inclined from the horizontal, oil may flow out through the gap of a seal ring. This should not be interpreted as an oil leak due to seal ring failure.