Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD(w/o Glow Plug Controller) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009588 1KD-FTV INTAKE / EXHAUST _0052325 INTAKE MANIFOLD(w/o Glow Plug Controller) A

1KD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD(w/o Glow Plug Controller)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE NO. 1 ENGINE UNDER COVER (w/ EGR Cooler)

Hide 4.DRAIN ENGINE COOLANT (w/ EGR Cooler)

Hide 6.REMOVE MANIFOLD STAY (w/o EGR Cooler)

a.
A099622

Remove the 2 bolts and manifold stay.


Hide 7.REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler)

a.

Disconnect the 2 vacuum switching valve connectors and the 4 vacuum transmitting hoses.


b.
A148131

Remove the 2 bolts and manifold stay with vacuum switching valve.


Hide 8.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A148132

Remove the bolt and injection pipe clamp.


c.

Remove the bolt and engine oil level dipstick guide.


d.

Remove the O-ring from the engine oil level dipstick guide.


Hide 9.REMOVE ELECTRIC EGR CONTROL VALVE WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

Hide 10.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 11.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 12.REMOVE VACUUM SWITCHING VALVE BRACKET (w/o EGR System)

a.
A233088

Remove the 2 bolts and vacuum switching valve bracket.


Hide 13.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/o EGR Cooler)

a.
A271948

Remove the 3 bolts and No. 2 intake air connector bracket.


Hide 14.REMOVE INTAKE AIR CONNECTOR (w/o EGR Cooler)

a.

Remove the 2 nuts, bolt and intake air connector.


Hide 15.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 16.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System without EGR Cooler)

Hide 17.REMOVE VACUUM CONTROL VALVE SET (w/ EGR Cooler)

a.
A149960

Disconnect the 2 connectors and 3 vacuum hoses.


b.

Remove the 2 bolts and vacuum control valve set.


Hide 20.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler)

a.
A149935

Remove the bolt and No. 3 intercooler support bracket.


Hide 21.REMOVE INTAKE MANIFOLD INSULATOR (w/ EGR Cooler)

a.
A149964

Remove the 2 bolts and intake manifold insulator from the intake manifold.


Hide 22.REMOVE INTAKE MANIFOLD

a.
A149936

w/ EGR Cooler:

Disconnect the common rail sub-harness connector from the intake manifold.


b.

w/o EGR Cooler:

Disconnect the vacuum hose and vacuum switching valve connector.


c.

Remove the 4 bolts, 2 nuts, intake manifold and gasket.

A260053
0.448,0.052 0.708,0.25 0.26,0.198 10 false *A 3.771,0.052 4.031,0.271 0.26,0.219 10 false *B
*A w/ EGR Cooler *B w/o EGR Cooler