Home › Engine / Hybrid System › 2KD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER(w/o EGR Cooler) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009590 2KD-FTV INTAKE / EXHAUST _0052339 EXHAUST MANIFOLD W/ TURBOCHARGER(w/o EGR Cooler) A

2KD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER(w/o EGR Cooler)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL EXHAUST MANIFOLD

a.
A301926
1.104,0.604 1.26,0.802 0.156,0.198 10 false 1 1.26,1.781 1.417,1.979 0.156,0.198 10 false 2 1.865,1.792 2.021,1.99 0.156,0.198 10 false 3 2.333,1.792 2.49,1.99 0.156,0.198 10 false 4 0.604,0.604 0.76,0.802 0.156,0.198 10 false 5 0.542,1.781 0.698,1.979 0.156,0.198 10 false 6 1.719,0.615 1.875,0.813 0.156,0.198 10 false 7 2.448,0.615 2.594,0.792 0.146,0.177 10 false 8

Install a new gasket, exhaust manifold and 8 plate washers to the cylinder head with 8 new nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:

Tighten the nuts in the order shown in the illustration.



Hide 2.CLEAN TURBOCHARGER SUB-ASSEMBLY

Hide 3.INSTALL TURBOCHARGER SUB-ASSEMBLY

a.

Temporarily install a new gasket and the turbocharger with 3 new nuts.

HINT:

When installing the turbo oil pipe, loosely install the 3 nuts so that the turbocharger and cylinder head can be aligned easily.



b.

Temporarily install the turbo oil pipe and manifold stay.

A110358
1.823,1.698 1.75,1.698 1.75,1.698 1.573,1.438 false 1.292,1.063 1.135,0.823 1.135,0.823 1.042,0.823 false 5.323,3.198 4.958,2.865 4.958,2.865 4.875,2.865 false 3.479,1.625 3.375,1.625 3.375,1.625 3.146,1.469 false 3.375,3.552 3.292,3.552 3.292,3.552 3.167,3.229 false 1.844,2.729 1.927,2.729 1.927,2.729 2.146,2.573 false 2.469,3.594 2.083,3.594 false 2.333,3.49 2.188,3.49 2.188,3.49 2.188,3.594 false 2.125,2.844 2.125,3.083 false 1.865,1.604 2.052,1.792 0.188,0.188 10 false *4 0.875,0.719 1.083,0.885 0.208,0.167 10 true *3 4.688,2.76 4.896,2.958 0.208,0.198 10 false *2 3.542,1.521 3.75,1.719 0.208,0.198 10 false *1 3.438,3.448 3.646,3.646 0.208,0.198 10 false *1 1.646,2.635 1.854,2.833 0.208,0.198 10 false *1 1.917,3.51 2.094,3.698 0.177,0.188 10 false A 2.073,3.083 2.313,3.25 0.24,0.167 10 false B
*1 New Gasket *2 Claw
*3 Narrow *4 Wide
V100135

Outside - -


HINT:

Wash the oil pipe before installing it.


i.

Temporarily install a new gasket and the turbo oil pipe with the 2 nuts, but only loosely install the nuts.

NOTICE:

The notch (wide part) of the gasket must face the engine.



ii.

Temporarily install a new gasket and the turbo oil pipe with the 2 bolts (labeled: A), but only loosely install the bolts.

NOTICE:

The claws of the gasket must face the turbo oil pipe.



iii.

Temporarily install a new gasket and the turbo oil pipe with the union bolt (labeled: B), but only loosely install the union bolt.


iv.

Temporarily install the manifold stay with the 2 bolts.

HINT:

The manifold stay's indented area must face the turbocharger.




c.

Tighten the bolts and nuts.

i.

Tighten the 3 nuts of the turbocharger.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


ii.

Tighten the 2 nuts of the turbo oil pipe.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


iii.

Tighten the 2 bolts of the turbo oil pipe.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


iv.

Tighten the union bolt.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


v.

Tighten the 2 bolts of the manifold stay.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)



Hide 4.INSTALL TURBINE OUTLET ELBOW

a.

Temporarily install a new gasket and the turbine outlet elbow (with turbocharger stay) to the turbocharger with the 4 new nuts.


b.

Temporarily install the turbocharger stay with the 4 bolts.


c.

Tighten the 4 nuts of the turbocharger.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


d.

Tighten the 4 bolts of the turbocharger stay.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 6.INSTALL VENTILATION HOSE HEAT INSULATOR

a.

Install the ventilation hose heat insulator with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 7.INSTALL AIR CLEANER ASSEMBLY

a.

Connect the No. 1 air cleaner hose.


b.

Install the cleaner with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


c.

Tighten the hose clamp.


d.

w/ Mass Air Flow Meter:

Connect the connector to the mass air flow meter.


e.

w/o Mass Air Flow Meter:

Attach the clamp and connect the intake air temperature sensor connector.


Hide 8.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ No. 1 Engine Cover)

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 13.INSTALL FRONT FENDER APRON SEAL UPPER

a.

for 4WD:

Install the front fender apron seal upper with the 5 clips.


b.

for 2WD:

Install the front fender apron seal upper with the 6 clips.


Hide 14.INSTALL FRONT FENDER SEAL

a.

Install the front fender seal with the 5 clips.


Hide 15.INSTALL NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)

Hide 16.INSTALL NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)