Home › Engine / Hybrid System › 2KD-FTV INTAKE / EXHAUST › EXHAUST MANIFOLD W/ TURBOCHARGER(for DPF) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009590 2KD-FTV INTAKE / EXHAUST _0052347 EXHAUST MANIFOLD W/ TURBOCHARGER(for DPF) A

2KD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER(for DPF)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 5.REMOVE NO. 1 ENGINE UNDER COVER

Hide 6.REMOVE NO. 2 ENGINE UNDER COVER

Hide 8.REMOVE FRONT FENDER APRON SEAL UPPER

a.

Remove the 5 clips and front fender apron seal upper.


Hide 9.REMOVE FRONT FENDER SEAL

a.

Remove the 5 clips and front fender seal.


Hide 10.REMOVE AIR CLEANER ASSEMBLY

a.
A271954

Detach the wire harness clamp and disconnect the mass air flow meter connector.


b.

Loosen the hose clamp and disconnect No. 1 air cleaner hose from the compressor inlet elbow.


c.

Remove the 2 bolts and air cleaner together with the No. 1 air cleaner hose.


Hide 11.REMOVE VENTILATION PIPE

a.
A271956

Remove the bolt and disconnect the 2 ventilation hoses and ventilation pipe.


Hide 12.REMOVE NO. 1 TURBO INSULATOR

a.
A255740

Remove the 2 bolts and No. 1 turbo insulator.


Hide 13.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A255741

Remove the bolt and No. 1 exhaust manifold heat insulator.


Hide 14.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A271949

Remove the 2 bolts and No. 2 exhaust manifold heat insulator.


Hide 15.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.
A254013

Remove the 2 bolts and No. 3 exhaust manifold heat insulator.


Hide 16.REMOVE TURBINE OUTLET ELBOW STAY

a.
A254014

Detach the wire harness clamp and remove the bolt, nut and turbine outlet elbow stay.


Hide 17.REMOVE NO. 2 TURBINE OUTLET ELBOW

a.
A254044

Remove the 3 nuts, No. 2 turbine outlet elbow and gasket.


Hide 18.DISCONNECT NO. 1 FUEL PIPE

a.
A254045

Detach the hose clamp and disconnect the No. 4 turbo water hose from the No. 4 water by-pass pipe.


b.

Disconnect the exhaust fuel addition injector connector.


c.

Remove the union bolt and gasket.


d.

Disconnect the No. 1 fuel pipe from the turbine outlet elbow.


Hide 19.REMOVE TURBINE OUTLET ELBOW

a.

Disconnect the No. 3 turbo water hose from the No. 3 water by-pass pipe.

A254046
1.844,0.083 1.938,0.083 1.938,0.083 2.104,0.156 false 0.708,1.729 0.802,1.729 0.802,1.729 0.969,1.833 false 0.615,2.198 0.719,2.198 0.719,2.198 0.875,2.292 false 2.885,0.146 2.99,0.146 2.99,0.146 3.135,0.26 false 3.198,2.563 3.104,2.563 3.104,2.563 2.927,2.406 false 3.854,2.156 3.854,2.052 3.854,2.052 3.76,1.896 false 1.708,1.781 1.615,1.781 1.615,1.781 1.448,1.875 false 2.948,0.656 2.854,0.656 2.854,0.656 2.698,0.75 false 3.729,1.021 3.625,1.021 3.625,1.021 3.448,1.25 false 1.646,0.01 1.938,0.229 0.292,0.219 10 false *1 0.479,1.625 0.667,1.813 0.188,0.188 10 false *1 0.406,2.094 0.604,2.313 0.198,0.219 10 false *2 2.688,0.063 2.917,0.25 0.229,0.188 10 false *2 3.281,2.469 3.552,2.646 0.271,0.177 10 false *6 3.771,2.219 3.927,2.375 0.156,0.156 10 false *1 1.781,1.677 2.042,1.906 0.26,0.229 10 false *4 3.01,0.563 3.219,0.771 0.208,0.208 10 false *3 3.802,0.927 4.021,1.115 0.219,0.188 10 false *5
*1 Gasket *2 Union Bolt
*3 No. 3 Water By-pass Pipe *4 No. 4 Water By-pass Pipe
*5 No. 3 Turbo Water Hose *6 Turbine Outlet Elbow



b.

Remove the 3 nuts, turbine outlet elbow and gasket.


c.

Remove the bolt, union bolt, gasket and No. 3 water by-pass pipe from the turbine outlet elbow.


d.

Remove the union bolt, gasket and No. 4 water by-pass pipe from the turbine outlet elbow.


Hide 20.DISCONNECT NO. 1 TURBO WATER HOSE

a.
A271940

Disconnect the No. 1 turbo water hose and No. 9 water by-pass hose.


Hide 21.REMOVE TURBOCHARGER STAY

a.
A254048

Remove the 2 bolts, nut and turbocharger stay.


Hide 22.REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY

a.
A301893
0.479,0.594 0.635,0.792 0.156,0.198 10 false A

Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe and 3 gaskets.

NOTICE:

Do not loosen the nut labeled A in the illustration.



Hide 23.REMOVE TURBOCHARGER SUB-ASSEMBLY

a.
A271955

Disconnect the 2 connectors and detach the wire harness clamp.


b.
A211839

Remove the 3 nuts, turbocharger and gasket.


Hide 24.REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY

a.

Disconnect the No. 2 water by-pass hose from the compressor inlet elbow.


b.
A271941

Remove the 2 nuts, bolt, No. 1 turbo water pipe and gasket from the turbocharger sub-assembly.


Hide 25.REMOVE COMPRESSOR INLET ELBOW

A271942

a.

Remove the No. 7 water by-pass hose and No. 9 water by-pass hose from the compressor inlet elbow.


b.

Remove the 2 nuts, compressor inlet elbow and gasket from the turbocharger sub-assembly.