Home › Engine / Hybrid System › 2TR-FE COOLING › WATER PUMP › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009594 2TR-FE COOLING _0052367 WATER PUMP A

2TR-FE COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 1.INSTALL ENGINE WATER PUMP ASSEMBLY

A253976
1.177,0.792 1.188,0.885 false
V100135

Bolt A
V100136

Bolt B


a.

Install a new gasket and the engine water pump assembly with the 10 bolts.

Torque:
for bolt A : 26 N*m (265 kgf*cm, 19 ft.*lbf)
for bolt B : 13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 2.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

A253977
1.594,0.604 1.677,0.573 false
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C


a.

Temporarily install the belt tensioner with the 3 bolts.

HINT:

Make sure the flanges of the bolts are contacting the tensioner surface.



b.

Install the tensioner with the 3 bolts.

Torque:
for bolt A : 43 N*m (438 kgf*cm, 32 ft.*lbf)
for bolt B : 40 N*m (408 kgf*cm, 30 ft.*lbf)
for bolt C : 21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 3.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

A254386
2.979,1.323 2.5,0.969 2.5,0.969 2.323,0.969 false 2.698,1.896 2.531,2.448 2.531,2.448 2.417,2.448 false 2.115,0.885 2.313,1.052 0.198,0.167 10 *1 2.219,2.354 2.417,2.521 0.198,0.167 10 *2
*1 Spacer
*2 Pulley


a.

Install the spacer and pulley with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 4.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring and the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Install the engine oil level dipstick.


Hide 6.INSTALL FAN SHROUD

A099679

a.

Install the fan pulley to the engine water pump.


b.

Place the shroud together with the fluid coupling fan between the radiator and engine.

NOTICE:

Be careful not to damage the radiator core.



c.

Install the coupling fan to the engine water pump with the 4 nuts. Tighten the nuts as much as possible by hand.


d.

Attach the claws of the shroud to the radiator as shown in the illustration.


e.

Install the shroud with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


f.

Install the fan and generator V belt (See page Engine / Hybrid System>2TR-FE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION).


g.

Tighten the 4 nuts of the fluid coupling fan.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


h.

Connect the reservoir hose to the upper radiator tank.


Hide 7.INSTALL AIR PUMP INLET (w/ Secondary Air Injection System)

a.

Install the air pump inlet to the upper radiator tank with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)