Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009575 2TR-FE ENGINE MECHANICAL _0052189 ENGINE ASSEMBLY A

2TR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.

NOTICE:

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.



b.

Lift the engine and remove it from the engine stand.

NOTICE:

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



c.

Place the engine onto a workbench.


Hide 3.INSTALL ENGINE ASSEMBLY

a.
A302629
1.24,0.469 1.24,0.542 false
V100135

Lower


Attach the engine sling device and chain block to the engine hangers.


b.

Slowly lower the engine assembly into the engine compartment.


c.

Install the engine mounting brackets with the 4 bolts and 4 nuts.

Torque:
38 N*m (388 kgf*cm, 28 ft.*lbf)


d.

Remove the 2 bolts and 2 engine hangers.


Hide 4.INSTALL REAR END PLATE

a.

Install the end plate with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the No. 1 water by-pass pipe to the rear end plate with the bolt.

Torque:
18 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 6.INSTALL CLUTCH DISC ASSEMBLY

Hide 7.INSTALL CLUTCH COVER ASSEMBLY

Hide 8.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

Hide 9.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.


a.

Install the 4 bolts and rear No. 1 engine mounting insulator.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 12.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)

Hide 13.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

Hide 16.INSTALL HOOD ASSEMBLY

a.

Install the hood with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the washer nozzle hose.


c.

Adjust the hood (See page Vehicle Exterior>DOOR / HATCH>HOOD>ADJUSTMENT).


Hide 17.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 18.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new O-ring and the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 19.INSTALL ENGINE OIL LEVEL DIPSTICK

Hide 20.CONNECT VANE PUMP ASSEMBLY

a.

Connect the vane pump with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the oil pressure switch connector.


Hide 21.CONNECT ENGINE WIRE

a.

Connect the wire clamp to the front engine mounting bracket LH with the bolt.

Torque:
13 N*m (128 kgf*cm, 9 ft.*lbf)


b.

Connect the 2 engine room junction block connectors and wire clamp.


c.

Connect the cable to the engine room junction block with the nut.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


d.

Install the engine room relay block cover (side).


e.

Install the engine room relay block cover (upper).


f.

Connect the ground wire with the nut.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


g.
A173606
1.271,1.802 1.625,1.948 0.354,0.146 10 true 45°

Connect the ground wire to the left side of the frame with the bolt so that it is within the range shown in the illustration.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


h.

Connect the sensor bracket to the right side of the frame with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


i.

w/ Secondary Air Injection System:

Connect the air fuel ratio sensor connector.


j.

w/o Secondary Air Injection System:

Connect the heated oxygen sensor connector.


k.
A173645
2.615,0.823 2.615,0.26 false 2.615,0.823 3.021,0.427 false 2.281,0.167 2.594,0.344 0.313,0.177 10 true 45° 2.76,0.177 3.073,0.354 0.313,0.177 10 true 45°

Push the engine wire through the dash panel into the cabin.

HINT:

The wire should be within the range shown in the illustration.



l.

Connect the ground wire with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


m.

Attach the wire harness clamp.


n.

w/ Secondary Air Injection System:

Connect the air injection driver connector.


o.

Connect the ECM connectors.

i.

Connect the 4 ECM connectors.


ii.

Install the glove compartment door.



Hide 22.CONNECT NO. 4 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)

Hide 25.CONNECT HOSE

a.

Connect the vacuum hose (for the brake master cylinder).


b.

Connect the purge line hose.


Hide 26.CONNECT HEATER WATER HOSE

a.

Connect the heater water inlet hose and heater water outlet hose to the heater pipe.


Hide 28.INSTALL FAN PULLEY

Hide 30.INSTALL AIR PUMP INLET (w/ Secondary Air Injection System)

Hide 35.INSTALL INTAKE AIR CONNECTOR AND AIR CLEANER ASSEMBLY

a.

Install the air cleaner and intake air connector assembly with the 4 bolts, and tighten the hose clamp.

Torque:
for air cleaner : 14 N*m (143 kgf*cm, 10 ft.*lbf)
for intake air connector : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for hose clamp : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the mass air flow meter connector and attach the wire harness clamps.


c.

Connect the No. 2 PCV hose.


d.

Connect the vacuum hose.


Hide 36.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 44.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

Hide 45.INSTALL NO. 1 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)