Home › Engine / Hybrid System › 2TR-FBE LUBRICATION › OIL AND OIL FILTER
RM1840EF _51 Engine / Hybrid System _009601 2TR-FBE LUBRICATION _0052405 OIL AND OIL FILTER A

2TR-FBE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with mineral oil will result in the loss of natural oil from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash the area thoroughly with soap and waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 1.REMOVE NO. 2 ENGINE UNDER COVER

Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil drain plug and drain the oil into a container.


c.

Clean and install the oil drain plug with a new gasket.

Torque:
38 N*m (382 kgf*cm, 28 ft.*lbf)


Hide 3.REMOVE OIL FILTER SUB-ASSEMBLY

a.
G038461
2.063,0.99 2.688,1.26 true 2.729,1.188 3.042,1.354 0.313,0.167 10 SST

Using SST, remove the oil filter.

SST
09228-07501  


Hide 4.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter.


c.
G038462
2.74,0.729 2.958,0.906 true 3.021,0.854 3.333,1.021 0.313,0.167 10 true SST

Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.


d.

Using SST, tighten the oil filter.

SST
09228-07501  

i.

Depending on the work space available, choose from the following.

If enough space is available, use a torque wrench to tighten the oil filter.

Torque:
17 N*m (175 kgf*cm, 13 ft.*lbf)

If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or use a common wrench.



Hide 5.ADD ENGINE OIL

a.

Add fresh engine oil.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil 5W-30
10W-30
(5W-30 is the best choice for good fuel economy and good starting in cold weather)
API grade SL, SM or SN multigrade engine oil 15W-40
20W-50


Standard Capacity:
Item Capacity
Drain and refill without oil filter change 5.3 liters (5.6 US qts, 4.7 Imp. qts)
Drain and refill with oil filter change 5.6 liters (5.9 US qts, 4.9 Imp. qts)
Dry fill 6.3 liters (6.7 US qts, 5.5 Imp. qts)



b.

Install the oil filler cap.


Hide 6.INSPECT FOR OIL LEAK

a.

Start the engine, and check that there are no oil leaks after performing maintenance.


Hide 8.INSTALL NO. 2 ENGINE UNDER COVER

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)